TP-Link TL-SG105 Installation Manual page 2

Specifications
General Specifications
IEEE802.3, IEEE802.3i, IEEE802.3u, IEEE802.3ab,
Standard
IEEE802.3x, IEEE802.1p
Protocol CSMA/CD
Ethernet:
10 Mbps (Half Duplex), 20 Mbps (Full Duplex)
Fast Ethernet:
Data Transfer Rate
100 Mbps (Half Duplex), 200 Mbps (Full Duplex)
Gigabit Ethernet:
2000 Mbps (Full Duplex)
10Base-T:
UTP category 3, 4, 5 cable (maximum 100 m)
EIA/TIA-568 100 Ω STP (maximum 100 m)
100Base-TX:
Network Media (Cable) UTP category 5, 5e cable (maximum 100 m)
EIA/TIA-568 100 Ω STP (maximum 100 m)
1000Base-T:
UTP category 5e cable (maximum 100 m)
EIA/TIA-568 100 Ω STP (maximum 100 m)
5/8/16 10/100/1000 Mbps Auto-Negotiation
Interface
RJ45 Ports
Power, Link/Act LED
LED Indicators
Advanced Features
IGMP Snooping, QoS (802.1p/DSCP Priority)
Transfer Method Store-and-Forward
MAC Address Learning Automatically learning, automatically aging
10Base-T: 14881pps/Port
Frame Forward Rate
100Base-TX: 148810pps/Port
1000Base-T: 1488095pps/Port
Wall Mountable Yes
TL-SG105/TL-SG105S: 52 mm
Distance Between
TL-SG108/TL-SG108S: 110 mm
Mounting Holes
TL-SG116: 200 mm
Environmental and Physical Specifications
Operating Temperature 0 ˚C to 40 ˚C (32 ˚F to 104 ˚F)
Storage Temperature -40 ˚C to 70 ˚C (-40 ˚F to 158 ˚F)
Operating Humidity
10% to 90%RH non-condensing
Storage Humidity
5% to 90%RH non-condensing
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Use only power supplies which are provided by manufacturer and in the origin
packing of this product. If you have any questions, please don't hesitate to contact us.
Frequently Asked Questions (FAQ)
Q1. The Power LED is not lit.
The Power LED should be lit when the power system is working
normally. If the Power LED is not lit, check as follows:
A1: Make sure the power adapter is connected to the switch with
power source properly.
A2: Make sure the voltage of the power supply meets the requirements
of the input voltage of the switch.
A3: Make sure the power source is ON.
Q2. The Link/Act LED is not lit when a device is connected
to the corresponding port.
It is recommended that you check the following items:
A1: Make sure that the cable connectors are firmly plugged into the
switch and the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet).
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR
code.
If you have any suggestions or needs on the product
guides, welcome to email techwriter@tp-link.com.cn.
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and
other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU
and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.