Advertisement
Quick Links
Advertisement
Related Manuals for Hunter MD520-01
Summary of Contents for Hunter MD520-01
- Page 1 ENGLISH MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 2 Important Instructions: Keep Instructions for future use...
- Page 3 7 feet Ladder opportunity to supply you with the best ceiling fan available anywhere in the world. Downrod Wiring Canopy Blades Operation, Maintenance, Light Kit Wall Control & Cleaning Troubleshooting Warranty Statement MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 4 Check box to see electrical codes. If you are unfamiliar with wiring, use a qualified Select a downrod length fan weight electrician. c.2 - Use only Hunter replacement parts. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 5 Ladder Pliers Wire Strippers Screwdrivers Power Drill 3.5 mm Drill 8 mm Drill Bit Hammer (optional) Bit (optional) (optional) (optional) If mounting to a support structure, you will also need these tools. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 6 The support structure must be able to support 5 Carefully choose the installation location times the weight of the fan. The weight of the fan is that allows for optimal air flow. located on the product packaging. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 7 To avoid possible electrical shock, before installing your fan, disconnect the power by Refer to warning w.1 on pg. 2 turning off the circuit breakers to the outlet box associated with the wall switch location. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 8 Downrod for angled ceilings or ceilings 3 m or higher If you need a longer downrod, follow the steps in the “Instructions for Installing a Longer Downrod” manual included with your fan. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 9 Let the canopy sit THE CANOPY OR WIRES. Place the top of the downrod. loosely on top of the fan. the downrod ball into the slot in the ceiling bracket. 20 cm 1 cm MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 10 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 11 Lift the canopy into place so that Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 12 Your blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning agents may damage the finishes. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 13 Make sure the light kit ring is securely attached. Failure to properly secure all three assembly screws could result in the light fixture falling. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 14 E27 sockets. When necessary, with the tabs in the light kit. Attach the replace with bulbs of same wattage. glass bowl to the light kit by twisting it clockwise until it snaps into place. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 15 1. Tighten the set Note: A power disconnect switch screw. should be installed in conjunction • Green from the capacitor to with the wall control. terminal 4. Tighten the set screw. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 16 Medium Speed the rocker switch center terminal. Tighten Low Speed the set screw. Fan Off Note: The rocker switch terminal may have an additional bottom terminal that will not be used. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 17 To switch the direction of air flow, move the For cleaning the fan, use soft brushes or the lights will be completely off. reverse switch to the opposite position. cloths to prevent scratching. Cleaning products may damage the finishes. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 18 • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on page 8. • Check the plug connection in the switch housing. MD520-01 • 10/06/14 • © Hunter Fan Company...
- Page 19 1. Warranty repairs shall only be performed by an Authorized Service Center appointed by Hunter Fan do Brasil, which 1. Hunter Ceiling Fans are warranted by Hunter Fan do Brasil for a period of 1 (one) year from the date of purchase by the provides specialized technicians and original parts, guaranteeing the service provided.