Loading Code-Libraries; Search Mode; Checking Code Library Number; Summary Of The Htrm 2 Modes - NAD M33 Owner's Manual

OPERATION
USING THE HTRM 2 REMOTE CONTROL

LOADING CODE-LIBRARIES

The HTRM 2 can store a different library of default NAD codes for each of
its Device Selector "pages. " If the original default library does not control
your NAD CD player, BD player, or other component, follow the procedure
below to change the code-library.
1 Begin by ensuring that the component you wish the HTRM 2 to control
is plugged in and powered-up ("on, " not merely in standby).
2 To enter the HTRM 2s Library Mode, simultaneously press-and-hold
both the desired Device Selector key and the [A/V PSET] key for 3
seconds, until the Learn LED turns green.
3 While keeping the HTRM 2 pointed toward the component, enter the
first appropriate three-digit code-library number from the table below.
4 Press [OFF]. If the component turns off, press [ENTER] to accept that
code-library number and exit the Library Mode.
5 If the component does not turn off, enter the next three-digit code-
library number from the table.
6 When you enter the correct number the component will turn off; press
[ENTER] to accept that code library number and exit the Library Mode.
LIBRARY NAD PRODUCT
CODE DESCRIPTION
Receiver/Processor
100
(Discrete ON/OFF)
Receiver/Processor
101
(Toggle ON/OFF)
102 S170
103 L75
Second Zone Commands
104
(Zone 2)
3112 Zone 3
4112 Zone 4
105 L70
106 L76
107 118
108 L53
109 L73
110 Stereo Receiver / Amplifier
111 Stereo Second Zone
112 Txx5 Series
200 CD Player
201 CD Player (old)
202 5170, 5240, 5340
203 5325
204 5060
205 M5
20
LIBRARY NAD PRODUCT
CODE DESCRIPTION
300 Tuner
301 L75, L76 Tuner
302 L70 Tuner
303 L53 Tuner
304 L73 Tuner
305 C425
306 C445
307 Txx5 Series Tuner
400 Tape Deck B
401 TAPE Deck A
500 TV 280
501 MR13
502 MR20
503 PMR45
600 T535, T562, T585, M55
601 T550, L55
602 T512, T531, T532, T571, T572
603 L70, L73 BD
604 L56
T513, T514, T515, T517,
605
T524, T533, T534
606 L53 BD

SEARCH MODE

If none of the codes from the table work, turn on the component and try
the "search" method as follows:
1 Enter Library Mode by simultaneously pressing-and-holding for 3
seconds the desired Device Selector key and the [A/V PSET] key, until
the Learn LED turns green.
2 Press-and-hold the HTRM 2's [R] or [T]) key. The remote will step
through all the available codes at a rate of approximately 1 per second.
3 When the component turns off, release the cursor key.
4 Press [ENTER] to accept that code library and exit Library Mode.
5 Try a few commands. Should you prove to have stepped past the
needed code-library, re-enter the Library Mode and use the cursor key
to step back to it.
NOTE
It is possible that search mode will find code-libraries that operate, at
least partially, some other brand (non-NAD) components. However, we
can only ensure the completeness or accuracy of NAD code-libraries. We
do not support the HTRM 2's operation with other-brand components.

CHECKING CODE LIBRARY NUMBER

1 Enter Library Mode by simultaneously pressing-and-holding for 3
seconds the desired Device Selector key and the [A/V PSET] key, until
the Learn LED turns green.
2 Press the [DISP] key.
3 The HTRM 2 indicates the current code-library by flashing its [DAC],
[CUSTOM], and [MACRO] keys.
For example, to indicate code-library #501, the HTRM 2 will flash [DAC] 5
times, pause, and then flash [MACRO] once. You might wish to make a note
of your components' code-library numbers.

SUMMARY OF THE HTRM 2 MODES

Mode
Learn/Copy/Punch Through
Delete Mode
Macro Record
Library Mode
Back Light Timeout
Factory Reset
Keys To Press (for 3 seconds)
Device Key + RES Key
Device Key + RTN Key
Macro Key + Function Key
Device Key + [A/V PSET] Key
DISP Key + Digit Key
See "Factory Reset" above