Advertisement
Quick Links
PowerCube 500 V200R001C10 Quick Guide
(CPS300-N18A1H1)
Issue: 04
Date: 2020-03-30
1
Overview
Appearance
Power module: CPS300-N18A1H1
Lithium battery: CBM20E-N14A1
Power
Color
Status
Meaning
Module
Indicator
The power module has no power input
Off
or is faulty.
Blinking
The power module is communicating
Run
Green
slowly
properly with upstream monitoring
indicator
(0.5 Hz)
equipment.
Blinking
The power module fails to communicate
fast (4 Hz)
with upstream monitoring equipment.
Off
There is no alarm.
Blinking
The power module has generated an
Alarm
slowly
alarm, which can be cleared.
Yellow
indicator
The power module has generated an
Steady
AC power failure or PV array fault alarm,
on
which can be cleared.
Off
The power module is normal.
Blinking
The power module has an external fault,
Fault
Red
slowly
which can be cleared.
indicator
Steady
The power module has an internal fault,
on
which cannot be cleared.
Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
Solar Hybrid Scenario
Lightning rod
CPE
Pole mounting kit
Pole mounting kit
Power module
Lithium
Battery
Color Status
Indicator
Off
Steady on The lithium battery is powered on.
Run
Blinking
Green
indicator
slowly
(RUN)
(0.5 Hz)
Blinking
fast (4 Hz)
Off
Alarm
Steady on
Red
indicator
Blinking
(ALM)
slowly
(0.5 Hz)
NOTE
The three indicators are steady on when the power module is
upgrading. They return to normal status after the upgrade is complete.
1
Antenna
PV modules
PV module support
Cantilever
Dome camera
Bullet
cameras
Lithium battery
Lithium battery
Pole
Meaning
The lithium battery has no power input or
is faulty.
The lithium battery is communicating
properly with upstream monitoring
equipment.
The lithium battery fails to communicate
with upstream monitoring equipment.
There is no alarm.
The lithium battery has generated a fault
alarm and needs to be replaced.
The lithium battery has generated a
protection alarm, which can be cleared.
Advertisement
Related Manuals for Huawei PowerCube 500 V200R001C10
Summary of Contents for Huawei PowerCube 500 V200R001C10
- Page 1 PowerCube 500 V200R001C10 Quick Guide (CPS300-N18A1H1) Issue: 04 Date: 2020-03-30 Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved. Overview Appearance Solar Hybrid Scenario Power module: CPS300-N18A1H1 Lightning rod Antenna PV modules PV module support Cantilever Dome camera Bullet...
- Page 2 Tools Routing Cables Through the Pole 1. Place the pole on a wooden case or a similar object. 2. Route a pull wire. 3. Route cables. Routing Cables Through the Solar Hybrid Pole CPE cable Mains AC cable, module ground cable, optical Module Mains AC fiber, camera cable, CPE...
- Page 3 Installing a Cantilever Installing Cameras and Cables Installing Cameras For the camera installation method, see the camera document. Installing Camera Cables For the cable connections at the camera side, see the camera document. Reserve the other ends of cables. (Optional) Installing the CPE For the CPE installation method, see the CPE document.
- Page 4 6. Install horizontal beams. 7. Install two PV modules. Keep the slots of horizontal beams facing inwards for installing PV modules. Partially tighten the bolts so that PV modules can be adjusted during installation. Spacing shim Ensure that the junction boxes on the rear of PV modules are positioned consistently.
-
Page 5: Installing An Antenna
Installing an Antenna Fastener and Lightning Rod Adjust the tilt angle of the lightning rod based on the site latitude. Site Lightning Rod Latitude Tilt Angle 0–15° 15° 16–25° 25° 26–30° 35° 31–45° 45° Installing an Antenna For the antenna installation method, see the antenna document. Installing the Power Module and Lithium Battery ... - Page 6 3. Install the power module 4. Install a power module. 5. Install the lithium battery hanging kit. hanging kit. The option to install a lithium battery depends on the scenario. No lithium battery is required in the grid-only scenario. 6. Install a lithium battery. 7.
- Page 7 3. Drill holes and install bolts in the holes. 2. Mark mounting holes. One wall mounting kit A and one wall mounting kit B are used for each module. Determine the number of wall mounting kits based on the number of modules to be installed. Hammer drill Level Marker...
-
Page 8: Installing Cables
10.(Optional) Install the second 9. Install a lithium battery onto the wall. lithium battery onto the wall. If two lithium batteries are required, install them onto two adjacent wall hanging kits. Installing the Power Module Antenna Installing Cables Route inter-device cables through the pole. Installing Ground Cables for Modules 12.1 1. - Page 9 Installing Cables for the Maintenance Compartment 12.2 Cable Hole Diameter Requirements Cable Hole Cable Outer Cable Type Silk Screen Diameter RS485 or FE communications cable RS485 or FE communications RS485/FE 6.8±0.3 mm cable Network device power cable Dome camera alarm linkage cable 12VDC Bullet camera power cable 9.3±0.4 mm...
- Page 10 7. (Optional) Install the door status sensor cable and dome camera 6. (Optional) Install the door status sensor. alarm linkage cable. Dome camera alarm cable 10.Push down the 8. (Optional) Connect cables to other devices. 9. Close the maintenance compartment door. sunshade until the spring fastener is ...
- Page 11 Battery Cable (1) Scale line Flat-head screwdriver Battery Cable (2) Prepare and install battery cables onsite as required by referring to Battery Cable (1) or Battery Cable (2). Flat-head screwdriver Battery cable Preparing PV Input Cables and Connecting Waterproof Connectors Flat-head Scale line screwdriver...
- Page 12 Installing Power Cables and Signal Cables 12.4 Ensure that caps and waterproof connectors are installed at all idle ports on the modules. Installing an RJ45 Communications Cable for a Lithium Battery Power Module and Lithium Batteries PV input AC input Power module Lithium battery Lithium battery...
-
Page 13: Verifying The Installation
1. Check the indicators on the power module and lithium batteries. Ensure that the green indicators are blinking slowly and that the yellow and red indicators are off. 2. If a problem is found, refer to the alarm definitions in the user manual for troubleshooting. Huawei Technologies Co., Ltd. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People's Republic of China e.huawei.com...