Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Displays2go BLKDMPTB
Summary of Contents for Displays2go BLKDMPTB
- Page 1 ASSEMBLY INSTRUCTIONS MANUAL BLKDMPTB WHITE FOLDING DUMP TABLE PAGE 1 OF 9...
- Page 2 ASSEMBLY INSTRUCTIONS MANUAL BLKDMPTB WHITE FOLDING DUMP TABLE PARTS IN CARTON: TABLE TOP (1 EACH - BOTTOM VIEW) JOINER STRIP (1 EACH) TABLE TOP EXTENDER (1 EACH - BOTTOM VIEW) SIDE WALL (2 EACH - INSIDE VIEW) END WALL (2 EACH - INSIDE VIEW)
- Page 3 ASSEMBLY INSTRUCTIONS MANUAL BLKDMPTB WHITE FOLDING DUMP TABLE PARTS IN CARTON: CAM LOCKING NUT (10 EACH) CAM LOCKING SCREW LONG SCREW (10 EACH) (8 EACH) LEG CAPS LONG SCREW COVER LEG SCREWS (4 EACH) (8 EACH) (16 EACH) YOU WILL NEED TO SUPPLY YOUR OWN SCREWDRIVER FOR INSTALLATION.
- Page 4 ASSEMBLY INSTRUCTIONS MANUAL BLKDMPTB WHITE FOLDING DUMP TABLE STEP 1 SLIDE PLACE TABLE TOP ON FLAT SURFACE WITH BOTTOM FACING UP. JOINER STRIP INTO SIDE OF TABLE TOP THAT HAS A RECESSED GROOVE (SEE FIGURE 1). FIGURE 1 FOLLOW THIS STEP AGAIN INSERTING THE...
- Page 5 ASSEMBLY INSTRUCTIONS MANUAL BLKDMPTB WHITE FOLDING DUMP TABLE STEP 2 PLACE (10) CAM LOCKING NUTS INTO EACH OF THE HOLES IN THE COMPLETED TABLE TOP SECTION. NOTE: MAKE SURE THE ARROW ON THE CAM LOCKING NUTS ARE FACINGTOWARDS THE CLOSEST EDGE OF THE BOARD.
- Page 6 ASSEMBLY INSTRUCTIONS MANUAL BLKDMPTB WHITE FOLDING DUMP TABLE STEP 4 LOCATE (2) END WALLS & (6) CAM LOCKING SCREWS. USING YOUR SCREWDRIVER, SCREW IN (3) CAM LOCKING SCREWS INTO THE END WALL. REPEAT STEP 4 FOR OTHER END WALL. END WALL...
- Page 7 ASSEMBLY INSTRUCTIONS MANUAL BLKDMPTB WHITE FOLDING DUMP TABLE STEP 6 ***NOTE*** WHEN ASSEMBLING, MAKE SURE THE CAM LOCKS ARE ON THE BOTTOM SIDE OF THE TABLE. LOCATE (2) END WALLS. INSERT CAM LOCKING SCREWS FROM END WALL INTO THE THE SIDE WALL END. TIGHTEN ALL (3) CAM NUTS. THEN INSERT (4) LONG SCREWS INTO THE HOLES ON THE END WALL.
- Page 8 ASSEMBLY INSTRUCTIONS MANUAL BLKDMPTB WHITE FOLDING DUMP TABLE STEP 7 LOCATE (2) FOLD-UP LEGS & (16) LEG SCREWS. WITH TABLE TOP ASSEMBLED, PLACE (1) SET OF FOLD-UP LEGS ONTO UNDERSIDE OF TABLE TOP. ALIGN ALL (8) HOLES ON TABLE TOP TO HOLES ON FOLD-UP LEGS. USING YOUR SCREW- DRIVER, SCREW IN (8) LEG SCREWS (SEE FIGURE 3).
- Page 9 ASSEMBLY INSTRUCTIONS MANUAL BLKDMPTB WHITE FOLDING DUMP TABLE STEP 8 WITH TABLE TOP STILL ON FLAT SURFACE AND LEG SECURLEY OPEN, INSERT (4) LEG CAPS ONTO END OF LEGS. LEG CAPS LEG CAPS FOLD-UP LEGS STEP 9 LOCATE (8) LONG SCREW COVERS. USING YOUR THUMB, INSERT SCREW COVER OVER EACH LONG SCREW (SEE FIGURE 4) LOCATED ON THE ENDS OF TABLE TOP ON END WALLS.
Need help?
Do you have a question about the BLKDMPTB and is the answer not in the manual?
Questions and answers