HIKVISION Safire DS-KH8520-WTE1 Configuration Manual

HIKVISION Safire DS-KH8520-WTE1 Configuration Manual

2nd generation video-intercoms
Hide thumbs Also See for Safire DS-KH8520-WTE1:

Advertisement

2nd generation Video-Intercoms
Configuration Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Safire DS-KH8520-WTE1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for HIKVISION Safire DS-KH8520-WTE1

  • Page 1 2nd generation Video-Intercoms Configuration Manual...
  • Page 2 Network Indoor Statio Configu atio Guide Symbol Convention The symbols that may be found in this document are define as follows. Symbol Descriptio Indicates a hazardous situatio which, if not avoided, will or Danger could result in death or serious injury. Indicates a potentiall hazardous situatio which, if not Cautio avoided, could result in equipment damage, data loss,...
  • Page 3: Table Of Contents

    Network Indoor Statio Configu atio Guide Contents 1 Local Operatio ..................1 1.1 Acti ate Indoor Statio ..................1 1.2 Configu atio Settin ..................1 1.2.1 Set Indoor Statio Network Parameters ........... 1 1.2.2 Set SIP Server .................... 2 1.2.3 Set Linked Device IP .................. 3 1.2.4 Set Indoor Statio No.
  • Page 4 Network Indoor Statio Configu atio Guide 2.4 Remote Configu atio ..................22 2.4.1 System ....................22 2.4.2 Video Intercom ..................27 2.4.3 Network ....................34 2.5 Person and Card Management ................ 37 2.5.1 Organizatio Management ..............38 2.5.2 Person Management ................39...
  • Page 5: Local Operatio

    Network Indoor Statio Configu atio Guide 1 Local Operatio 1.1 Acti ate Indoor Statio You can only configu e and operate the indoor statio afte creatin a password for the device acti ation Steps 1. Power on the device. It will enter the acti atio page automati ally. 2.
  • Page 6: Set Sip Server

    Network Indoor Statio Configu atio Guide Two ways are available for you to set IP address: DHCP, and set IP address manually. 1. Tap Settin → → Configu atio → to enter the network settin page. Note Default admin password is 888999. Figure 1-2 Network Settin 2.
  • Page 7: Set Linked Device Ip

    Network Indoor Statio Configu atio Guide Note Rebootin the indoor statio is required when you switch the SIP protocol • between the private SIP protocol and the standard SIP protocol. All linked device IP should be configu ed again afte you change the SIP protocol •...
  • Page 8 Network Indoor Statio Configu atio Guide Figure 1-3 Device Management (Private SIP) Figure 1-4 Device Management (Standard SIP) 2. Tap Main Door Statio to pop up the device informatio dialog.
  • Page 9: Set Indoor Statio No

    Network Indoor Statio Configu atio Guide Figure 1-5 Device Informatio Restore the door to restore the parameters of the door statio via indoor station station Sync to synchronize the language of door statio to indoor station 3. Select the device to link. Edit the network parameters. 1.2.4 Set Indoor Statio No.
  • Page 10: Add Camera

    Network Indoor Statio Configu atio Guide Figure 1-6 Set Indoor Statio No. 2. Select Indoor Statio to set the indoor statio No. (Room No.) and the floo No. 3. Select Indoor Extension to set the indoor extension No. and the room name. 1.2.5 Add Camera Steps 1.
  • Page 11: Zone And Alarm Settin

    Network Indoor Statio Configu atio Guide 3. Enter the device name and IP address. 4. Enter the password of the camera. 5. Tap OK to add the camera. 1.2.6 Zone and Alarm Settin Zone Settin You can set the zone type, alarm type and delay tim and other parameters of 8 zones.
  • Page 12 Network Indoor Statio Configu atio Guide Note 7 zone types are selectable: Panic Button Door Magnetic Smoke Detector, • Acti e Infrared, Passive Infrared, Gas Detector, and Doorbell. 3 alarm types are selectable: 24h Alarm, Instant Alarm, and Delay Alarm. •...
  • Page 13: Password Settin

    Network Indoor Statio Configu atio Guide Figure 1-9 Arming Mode Settin 3. Arm the selected zone. Note Zones are configu able on the arming mode page. • 24H alarm zone including smoke detector zone and gas detector zone will be •...
  • Page 14: Synchronize Time

    Network Indoor Statio Configu atio Guide Enter the unlock password and room No. on the door statio to open the door. Arm/Disarm Arm or disarm the zone for the indoor statio by entering the arm/disarm password. Note Arm/Disarm settin page is hidden by default. Tap Settin →...
  • Page 15: Sound Settin

    Network Indoor Statio Configu atio Guide Figure 1-10 Sync Time 2. Enable Enable NTP. 3. Set the synchronizing interval, enter the IP address/domain of NTP server and port No., and select the tim zone. Note The default unit of synchronizing interval is minute. 1.5 Sound Settin You can set the ringtone, ring duration call forwarding time volume of microphone and loudspeaker, enable/disable touch sound and auto-answer functio on call...
  • Page 16: Restore Indoor Statio

    Network Indoor Statio Configu atio Guide Figure 1-11 Call Settin 2. Set corresponding parameters. Ringtone There are 3 ringtones by default, and you can custom and import at most 4 ringtones via Batch Configuration Tool or Safire Control Center AC Client Software.
  • Page 17: System Maintenance

    Network Indoor Statio Configu atio Guide Steps 1. Tap Settin → → Configu atio → to enter the restore default settin page. Figure 1-12 Restore Default Settin 2. Tap Restore Default Settin to restore the default settin and reboot the system.
  • Page 18 Network Indoor Statio Configu atio Guide Reboot Device Tap Reboot Device to reboot the system. Language Tap System Language to change the system language. Note The indoor statio supports 12 languages. Brightness Adjustment Tap + or - to adjust the brightness. Figure 1-13 Brightness Adjustment Preference Tap Preference to enter the preference page.
  • Page 19: Linked To The Mobile Client

    Network Indoor Statio Configu atio Guide Do Not Disturb Tap Settin → to enter the call settin page. Tap Do Not Disturb to choose Close, All Day or Schedule. Note If you choose the Schedule, you should set the start tim and end time 1.8 Linked to the Mobile Client Steps 1.
  • Page 20: Remote Operatio Via The Client Soft Are

    Network Indoor Statio Configu atio Guide 2 Remote Operatio via the client soft are The Video Intercom module provides remote control and configuration on video intercom products via the Safire Control Center AC client software. 2.1 Acti ate Device Remotely You can only configu e and operate the indoor statio afte creatin a password for the device acti ation Before You Start...
  • Page 21: Add Video Intercom Devices

    Network Indoor Statio Configu atio Guide Device management includes device acti ation adding device, editin device, and deletin device, and so on. After running the Safire Control Center AC, video intercom devices should be added to the client software for remote configuration and management. 2.2.1 Add Video Intercom Devices Steps Note...
  • Page 22 Network Indoor Statio Configu atio Guide 7. Input the required information Nickname Edit a name for the device as you want. Address Input the device's IP address. The IP address of the device is obtained automati ally in this adding mode. Port Input the device port No.
  • Page 23: Modify Network Informatio

    Network Indoor Statio Configu atio Guide Figure 2-2 Add Device by IP Address Note Add Multipl Online Devices: If you want to add multipl online devices to • the client soft are, click and hold Ctrl key to select multipl devices, and click Add to Client to open the device adding dialog box.
  • Page 24: Reset Password

    Network Indoor Statio Configu atio Guide Figure 2-3 Modify Network Informatio Note You should enter the admin password of the device in the Password fiel of the pop- up window to modify the parameters. 2.2.3 Reset Password According to the di erent video intercom devices, the soft are provides two di erent methods for restoring the default password or resetti the password.
  • Page 25: System Configu Atio

    Network Indoor Statio Configu atio Guide 3. Reset password. This choice is available to door stations Our technical engineer will send you a fil to you. Afte receiving a fil from the technical engineer, select Import File from Key Importin Mode drop- down list and click ...
  • Page 26: Remote Configu Atio

    Network Indoor Statio Configu atio Guide Max. Speaking Duratio with Door Statio Input the maximum duratio of speaking with the door station ranging from 90 seconds to 120 seconds. 4. Click Save to save the setting Figure 2-5 System Configu atio 2.4 Remote Configu atio In the device list area, select a device and click Remote Configu atio to enter the remote configu atio page.
  • Page 27 Network Indoor Statio Configu atio Guide Device Informatio Click Device Informatio to enter device basic informatio page. You can view basic informatio (the device type, and serial No.), and version informatio of the device. Figure 2-6 Device Informatio General Click General to enter device general parameters settin page. You can view and edit the device name and device ID.
  • Page 28 Network Indoor Statio Configu atio Guide Figure 2-8 Synchronize Time Select Time Zone or Enable NTP. Click Save to save the tim setting Time Zone • Select a tim zone from the drop-down list menu. Click the Synchronizatio . • Check the checkbox of Enable NTP to enable NTP.
  • Page 29 Network Indoor Statio Configu atio Guide Figure 2-9 System Maintenance Click Reboot and the system reboot dialog box pops up. Click Yes to • reboot the system. Click Restore Default Settin to restore the default parameters. • Click Restore All to restore all parameters of device and reset the device •...
  • Page 30 Network Indoor Statio Configu atio Guide Click Export Configu atio File and the export fil window pops up. • Select the saving path of remote configu atio file and click Save to export the configu atio file Click ... to select the upgrade fil and click Upgrade to remote upgrade •...
  • Page 31: Video Intercom

    Network Indoor Statio Configu atio Guide Note The new password and confir password should be identi al. • Afte editin the password of device, click refresh butto from the • device list, the added device will not be there. You should add the device again with new password to operate the remote configu ation RS-485 Click RS485 to enter the RS-485 settin page.
  • Page 32 Network Indoor Statio Configu atio Guide Steps 1. Click ID Configu atio to enter device ID configu atio page. Figure 2-12 ID Configu atio 2. Select the device type from the drop-down list, and set the corresponding information 3. Click Save to enable the device number configu ation Time Parameters Steps 1.
  • Page 33 Network Indoor Statio Configu atio Guide Note Maximum ring duratio is the maximum duratio of indoor statio when it is • called without being received. The range of maximum ring duratio varies from 30s to 60s. Maximum live view tim is the maximum tim of playing live view of the •...
  • Page 34 Network Indoor Statio Configu atio Guide Figure 2-15 Zone Alarm 2. Select a zone type from the drop-down list menu. 3. Select an alarm mode from the drop-down list menu. 4. Set the zone status: NO or NC. 5. Set the entering delay, and exitin delay. 6.
  • Page 35 Network Indoor Statio Configu atio Guide When the zone type is set to be Delay Alarm, only under arming mode, the • indoor statio will receive alarm message when the detector is triggered. Under disarming mode, it will not receive alarm message when the detector is triggered.
  • Page 36 Network Indoor Statio Configu atio Guide Steps 1. Click Export to export the added device informatio file 2. Edit parameters of added devices in batch in the exported file 3. Click Import to pop up importin box, and open the edited added device informatio file Figure 2-17 Import Added Device Informatio Volume Input and Output...
  • Page 37 Network Indoor Statio Configu atio Guide 3. Click Save to enable the setting Ring Import Steps 1. Click Ring Import to enter the ring configu atio page. Figure 2-19 Ring Import 2. Click + to add the ring, and click x to delete the imported ring. Note The ring to be imported should be in the wav format, and the size of the ring •...
  • Page 38: Network

    Network Indoor Statio Configu atio Guide Figure 2-21 SIP Protocol Incoming Call Linkage Enter a short descriptio of your task here (optional) Steps 1. Click Incoming Call Linkage to enter configu atio the page. Figure 2-22 Incoming Call Linkage 2. Enable and select triggers. When the calling incoming, the alarm you linked will be triggered.
  • Page 39 Network Indoor Statio Configu atio Guide Figure 2-23 Local Network Configu atio 2. Enter the local IP address, subnet mask, gateway address, and port No. 3. Click Save to enable the setting Note The default port No. is 8000. • Afte editin the local network parameters of device, you should add the •...
  • Page 40 Network Indoor Statio Configu atio Guide Figure 2-24 Linked Network Configu atio 2. Enter the master statio IP address, (main) door statio IP address, SIP server IP address, management center IP address, and doorphone IP address. 3. Select the main door statio type from the drop-down list. 4.
  • Page 41: Person And Card Management

    Network Indoor Statio Configu atio Guide Click Advanced Settin to enter DNS address settin page. Edit the IP address and click Save. Figure 2-25 DNS Settin Configu e Mobile Client Connectio Configure Safire Connect server parameters before viewing videos via mobile client. Before You Start Make sure the indoor statio connects to the network.
  • Page 42: Organizatio Management

    Network Indoor Statio Configu atio Guide Figure 2-26 Select Scene Note Once the scene is configu ed, you cannot change it later. Click → to enter the Person and Card Management page. Figure 2-27 Person and Card Management The page is divided into two parts: Organizatio Management and Person Management.
  • Page 43: Person Management

    Network Indoor Statio Configu atio Guide Steps 1. In the organizatio list on the left click Add to pop up the adding organizatio page. 2. Input the Organizatio Name as desired. 3. Click OK to save the adding. 4. You can add multipl levels of organization according to the actual needs. 1) You can add multipl levels of organization according to the actual needs.

Table of Contents