Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Denso VehicleMRI
Summary of Contents for Denso VehicleMRI
-
Page 2: Table Of Contents
Table of Contents Introduction _________________________________________________________________ Safety Information ____________________________________________________________ Setting up the MBT ___________________________________________________________ Typical Operation _____________________________________________________________ VehicleMRI Cannot Detect the MBT Vehicle Interface _____________________________ General Troubleshooting _______________________________________________________ Flow Chart Troubleshooting ____________________________________________________ Specifications _______________________________________________________________ Manufacturer’s Warranty Summary _____________________________________________ Compliance ________________________________________________________________ Company Information ________________________________________________________ DENSO Products and Services Americas, Inc. -
Page 3: Introduction
This manual contains instructions to assist you with the basic operating functions of the Mini Bluetooth® (MBT) vehicle communication interface. The MBT The MBT is the vehicle communication interface required for VehicleMRI. It is paired to an Android smartphone or tablet via Bluetooth allowing communication between the vehicle ECU and the mobile application. -
Page 4: Safety Information
Save This User Guide For your safety, read all instructions. Use your inspection tool only as described in this user guide. For additional information, please contact DENSO. Safety Instructions 1. Do not insert the MBT into the vehicle OBD-II port while the ignition is “ON.”... -
Page 5: Setting Up The Mbt
Setting up the MBT Before using VehicleMRI, the application will need to discover the MBT through the Android smart phone or tablet (device) Bluetooth connection. Vehicle-Side Setup 1. Plug the MBT into the DLC of the vehicle that has a charged battery and note the serial number on the label. -
Page 6: Typical Operation
Typical Operation Paired Bluetooth® Device Once the MBT has been selected within the VehicleMRI application, a “request to pair” with the Host device (phone/tablet) will appear during the first scan. Scanning with VehicleMRI Plug the MBT into the vehicle DLC. Follow the setup instructions in VehicleMRI to discover and connect to your MBT. -
Page 7: Vehiclemri Cannot Detect The Mbt Vehicle Interface
Typical Operation CONTINUED VehicleMRI Cannot Detect the MBT Vehicle Interface If the MBT vehicle interface experiences a reset condition, the device name detected by Bluetooth in your phone or tablet will revert to a factory default name and will not communicate with the VehicleMRI application. - Page 8 V is Solid Red, B is Slow Blink Blue and H is Solid Red. What To Do if a Factory Reset Occurs? Contact DENSO technical support to confirm the failure and determine disposition. DENSO Products and Services Americas, Inc. Page 6...
-
Page 9: General Troubleshooting
Verify the serial number displayed on the number. When the serial number is MBT to Host device Serial number of MBT VehicleMRI application matches the serial incorrectly displayed or is not displayed, (Android phone/ number on the MBT label. go to Step 10. - Page 10 Verify that the location permission Disabled location has been “enabled” or set to MAF sensor result offset permission for the Select the VehicleMRI app and click on “Permissions”. “allowed” for the VehicleMRI VehicleMRI app application. Confirm that location permissions are “allowed”.
-
Page 11: Flow Chart Troubleshooting
4: The has been paired to the host device (phone/tablet). 5: The MBT serial number detected by the VehicleMRI application is the same as on the unit connected to the vehicle. 6: Turn the vehicle ignition switch to the ON position (engine not running). - Page 12 2: Unable to install the application Verify that Prerequisites 4 through 8 are met 3: Unable to download or install the VehicleMRI application as the screen turns ON and OFF Verify that Prerequisite 7 is met 4: Settings screen displaying “Device not found” or cannot nd devices...
-
Page 13: Specifications
Operating voltage: 10 ~ 17 VDC Environmental Temperature range 0°F ~ +50°F Mechanical Case material: ABS plastic Dimensions: 3.6” x 1.7” x 0.9” (92mm x 44mm x 22mm) Weight: 2 oz DENSO Products and Services Americas, Inc. Page 11 VehicleMRI MBT Vehicle Interface... -
Page 14: Manufacturer's Warranty Summary
Product and Warranty Coverage Period. This warranty is the only warranty made by DENSO with respect to the Product, and is in lieu of all obligations or liabilities on the part of DENSO for damage arising out of or in connection with the sale, use or performance of the Product, including, without limitation, any lost profits or any other consequential, incidental, special or exemplary damages of any kind. -
Page 15: Compliance
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. DENSO Products and Services Americas, Inc. Page 13 VehicleMRI MBT Vehicle Interface... -
Page 16: Company Information
Company Information DENSO Products and Services Americas, Inc. 3900 Via Oro Avenue Long Beach, CA 90810 Technical Support 1-877-675-5463 Website www.densovehiclemri.com © 2020 DENSO LA990009-2971 DENSO Products and Services Americas, Inc. Page 14 VehicleMRI MBT Vehicle Interface...