1. Manuals
  2. Brands
  3. EVERSPRING Manuals
  4. Accessories
  5. ST815
  6. Manual

EVERSPRING ST815 Manual

Illumination sensor with lcd
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
ST815
Illumination Sensor with LCD
The Illumination Sensor with LCD (refer to as Illumination Sensor hereafter) is a
TM
Z-Wave
enabled device which is fully compatible with any Z-Wave
TM
network. Z-Wave
enabled devices displaying the Z-Wave
used with it regardless of the manufacturer, and ours can also be used in other
TM
manufacturer's Z-Wave
enabled networks. Inclusion of this sensor on other
manufacturer's Wireless Controller menu allows remote operation of connected
modules when the sensor is triggered. Z-
TM
enabled
TM
logo can also be
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ST815 and is the answer not in the manual?

Questions and answers

Related Manuals for EVERSPRING ST815

Summary of Contents for EVERSPRING ST815

  • Page 1 ST815 Illumination Sensor with LCD The Illumination Sensor with LCD (refer to as Illumination Sensor hereafter) is a Z-Wave enabled device which is fully compatible with any Z-Wave enabled network. Z-Wave enabled devices displaying the Z-Wave logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-Wave...

  • Page 2: Choosing A Suitable Location

    Function Description LCD Indication Plastic Wall Plug Exclusion 1. Have Z-Wave Controller entered flashes exclusion mode. 2. Pressing key 3 times within ESC/ 1.5 seconds will enter exclusion mode. Node ID has been excluded. The RF reading displays 00 (MODE 5) Reset Long beep tone is sounded as 1.

  • Page 3: Operation

    Insert 3 AA-size 1.5V alkaline batteries to the battery compartment, ensuring Press any key will beep once and extend the backlight for another 12 seconds. correct polarity is put. The illumination detecting range is from 0 to 3000 LUX. When illumination reaches the limit (3000 LUX), MAX icon will be displayed on the screen.
  • Page 4 If lux of ambient light is greater than preset trigger-OFF value, Illumination Sensor 1500 lux will emit RF signal to the nodes of Grouping 2. The screen of sensor will return to MODE 1 and the icon is flashing with backlight illuminates and 4 continuous Restriction beeps sound for 1 second.
  • Page 5 Note: If no key has been pressed, it will return to MODE 1 automatically after 12 seconds. While you are setting the sensor, the function of detecting trigger-OFF is set to disable to avoid false detection (because hands may obstruct the light to Illumination Sensor during setting).
  • Page 6 Grouping 1 includes POWER_APPLIED, SENSOR_MULTILEVEL _REPORT, ALARM_REPORT Command: ALARM_REPORT and BATTERY_REPORT_COMMAND [Command Class Alarm, Alarm Type = 0x01, Alarm Level = 255(0xFF)] Grouping 2 includes BASIC_SET The users can also enquire the battery status of the sensor by sending 1-1 Grouping 1 (Max. Node = 1) BATTERY_ GET command via controller.
  • Page 7 Default Set/ Parameter Function Size Value Unit Factory Description (Byte) Default % of Set basic set value to be Basic Set Level 0~99 Brightness 99 / 99 on (or set Lux Level)/off (Dimmer Level) 0: Disable Set lux trigger-ON value Lux Trigger-ON 30~1000 300 / 0...

  • Page 8: Troubleshooting

    Specifications This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operating Frequency 868.42 (ST815-1) / 908.42 (ST815-2) Illumination Detecting Range 0 ~ 3000 LUX WARNING: Luminance Unit Protection Degree IP44 (indoor &...

Table of Contents