Related Manuals for MPM MPM-50-PX-51
Summary of Contents for MPM MPM-50-PX-51
- Page 1 Under Cabinet Range Hood Operation Manual MPM-50-PX-51,52 MPM-60-PX-61,62 MPM agd S.A. ul. Brzozowa 3, 05-822 Milanówek Tel. +48 22 380 52 00 Fax: +48 22 724 70 00 E-mail: mpm@mpm.pl www.mpm.pl...
- Page 2 Dear Customers, Thank you for your trust and purchasing of our product. Our device was designed in order to meet your expectations in terms of functionality and esthetics. It will certainly become a practical and decorative element for every kitchen. We hope that the device will serve you for many years. Before starting the range hood assembly, please read attentively this Operation Manual.
- Page 3 General safety and assembly requirements • This Operation Manual shall be maintained, in order to be able to use it in every further moment. • Read this Operation Manual attentively, as it contains the detailed information regarding the installation, assembly and maintenance of the hood.
- Page 4 • Do not disconnect the plug from the socket drawing the power cable. • The power cable may not touch the hot surface. • Do not start the device if the power cable is damaged. • The replacement of the damaged power cable may be performed by the manufacturer;...
- Page 5 Environment protection The device was designed and manufactured from the high-quality recycling materials and components. The crossed waste container sign (Fig. A) on the product means that it is subject to the selective waste collection, according to the Directive of the European Parliament and Council 2012/19/EC.
-
Page 6: Technical Specifications
Technical specifications The technical specifications specified in this Operation Manual, and in the labels attached to the hood, have been obtained by measurements and calculations made according to the EU resolution No. 65/2014 and 66/2014. Fig.1 General view of the range hood. Control panel Aluminium fat filter Hood body... - Page 7 Operation The hood is intended for sucking in the vapours during the meals cooking. The device may work in two modes. In its standard version, the hood device is designed for operation in the extractor hood mode. As the extracting hood: the vapours are extracted from the premise through the withdrawal tube.
- Page 8 Fig.3 Change of the hood function. part under the plug Plug Fig.4 Chimney instalation. Symbol chimney instalation Symbol chimney disassembly...
- Page 9 Fig.5 The place of sticking the label. Hood installation NOTE: The use of screws and fastening elements not specified in the Operation Manual may cause the electrical shock. The minimum distance of hood hanging between the surface of kitchenware placement over the cooking range (gas, electric range), and lowest part of the hood (Fig.6) shall amount at least 45 cm for electric cooking ranges and at least 65 cm for gas cooking ranges.
- Page 10 The installation of the Fig. 6 Recommended distances from the cooking range. hood and chimney body is shown at the figures (Fig.7 - Fig.12). The hood is equipped with the fixing pins matching to the most part of walls and ceilings.
- Page 11 hood, make the opening for the flue pipe in the shelf, with a minimum diameter of 140 mm. 2. Remove the aluminium fat filter (Fig.8). 3. Place the hood in the assembly place, mark the places for openings in the cabinet bottom, remove the hood and drill the openings Ø2 for the screws.
- Page 12 Fig. 7 Hood to the cabinet assembly. Fig. 8 Aluminium fat filter removing.
- Page 13 Fig. 9 Hood assembly to the wall. (50) LO= 496mm (60) LO= 596mm O4x16 Fig. 10 Assembly dimensions.
- Page 14 Fig. 11 Screw plugs assembly. 2 x O5 x 45mm 4 x O8 x 40mm Fig. 12 Hood hanging.
- Page 15 Electrical connections The network voltage shall correspond to the voltage indicated at the plate placed inside the hood. If the hood is equipped with a plug, insert it into the socket complying with the applicable requirements, and located in the easily accessible place.
-
Page 16: Light Replacement
clean the filter regularly reduces the hood performance, and may cause the fire. The filter shall be cleaned at least every 35 hours of hood operation. Coal filter The hood may be equipped with the coal filter. The coal filter is used when the hood is not connected to ventilation duct only. - Page 17 NOTE: Before the replacement of lamps, switch the hood power off. Do not touch the lamps when they are hot. Be attentive not to touch the lamp installed with hands. Fig. 14 Lights replacement. GU10 Mark lamp installation Mark lamp removal Hood operation control The hood is equipped with the mechanical control system.
- Page 18 How to reduce the cooking impact to the environment In order to reduce the energy consumption, cook in the kitchenware under the cover. The hood aluminium filters shall be kept clean (the recommended time of work of aluminium filter between its cleaning: max. 35h of hood operation).
- Page 19 Product characteristics Product characteristics are placed inside the hood.
-
Page 20: Troubleshooting
Troubleshooting Trouble Possible cause Trouble elimination Touch and hold for approx.. 8 After 35 hours of operation, the During the hood operation, the seconds the "-" touch button. hood informs on the need to clean pulsing "F"symbol is displayed. Wash the filter in the or replace the fat filter.
Need help?
Do you have a question about the MPM-50-PX-51 and is the answer not in the manual?
Questions and answers