Stihl FS 410 C-M Instruction Manual
  1. Manuals
  2. Brands
  3. Stihl Manuals
  4. Brush Cutter
  5. FS 410 C-M
  6. Instruction manual

Stihl FS 410 C-M Instruction Manual

Hide thumbs Also See for FS 410 C-M:
Table of Contents

Advertisement

Quick Links

STIHL FS 410 C-M, 460 C-M,
490 C-M
Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FS 410 C-M and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Stihl FS 410 C-M

Summary of Contents for Stihl FS 410 C-M

  • Page 1 STIHL FS 410 C-M, 460 C-M, 490 C-M Instruction Manual...

  • Page 3: Table Of Contents

    Minimize Wear and Avoid Damage Main Parts Specifications This instruction manual is protected by copyright. All rights reserved, especially the rights to reproduce, translate and process with electronic systems. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 4 When not using the machine, it must be Intake air: Winter laid down in such a way that it does not operation endanger anyone. Ensure that the machine cannot be used without Handle heating authorization. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 5 Only use cutting attachments and moving parts of the machine. Do not accessories that are explicitly approved for this power tool model by STIHL or are technically identical. If you have any FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 6 Cutting attachment or – refueling. interchangeable attachment: correctly fitted, secure and in Do not fuel a hot engine – fuel may spill perfect condition and cause a fire. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 7 Right hand on control handle, left hand on grip on handlebar. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 8 – do not run the engine modifying the shape (out of balance). Be particularly careful when working on unnecessarily, accelerate the engine difficult, densely grown terrain. only when working. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 9 If there is a risk of fire, do not requirements. use metal cutting attachments in the FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 10 Some of the following symbols are applied to the outside of the deflector to indicate the approved combination of cutting attachment and deflector. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 11 – dull teeth may result in the 2 cm – do not cut thicker stems – risk of blade cracking and shattering and accidents. causing serious injury. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 12 STIHL recommends that you use the non-shaded area of the circular saw blade. Always start the cut with this area of the blade. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 13: Approved Combinations Of Cutting Attachment, Deflector, Limit Stop And Harness

    Chisel tooth circular saw blade 200- 22 (4119), chisel tooth circular saw blade 200-22 HP (4000) FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 14 Limit stop for circular saw blades, items 3 and 4 10 Limit stop for circular saw blades, items 5 and 7 Harness 11 Full harness must be used FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 15: Mounting The Bike Handle

    Do not change the position of the Raise the grip of the wing screw (8) clamp moldings on the handlebar to the upright position. until the control handle is mounted. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 16 (7). the drive tube and put it down on the and tighten it down firmly. right-hand side of the machine. Only tighten the wing screw moderately. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 17 Line up the handlebar Rotate the wing screw clockwise until it becomes difficult to turn. Tighten down the wing screw firmly. Move the handlebar to the required position. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 18: Adjusting The Throttle Cable

    WARNING counterclockwise. Stop (3) is approved for circular saw blades only and must therefore be mounted before fitting a circular saw blade. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 19: Mounting The Cutting Attachment

    (3) for circular saw blades. Recommendation: The guard ring must be mounted with particular care. Have this work performed by your dealer. STIHL recommends your contact a STIHL servicing dealer. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 20 The output shaft (1) must be blocked with the stop pin (2) to mount or remove cutting attachments. The stop pin is included with the machine and is available as a special accessory. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 21 Unscrew the mounting nut clockwise. Pull the cutting attachment with its mounting hardware off the gearbox. Place the cutting attachment (1) in position. Place the cutting attachment (1) in position. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 22: Fuel

    Use only high-quality brand-name fuel. Pour oil into canister first, then gasoline with a minimum octane rating add gasoline and mix thoroughly. of 90 – leaded or unleaded. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 23: Fueling

    Closing the filler cap requirements. Place the cap in the opening. Turn the cap clockwise as far as stop and tighten it down as firmly as possible by hand. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 24: Fitting The Full Harness

    20 cm above the ground. machine's perforated rail (3) – see “Attaching Machine to Harness”. Find the right attachment point for the cutting attachment you are using – see "Balancing the Machine". FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 25: Starting / Stopping The Engine

    The ignition is bulb (4) at least five times – even if switched on again automatically after the bulb is filled with fuel. the engine stops. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 26 Attach the machine to the shoulder runs. strap. If the engine does not start: Turn the Machine is ready for use. choke knob to the start position } and repeat starting procedure. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 27: Operating Instructions

    – see "Storing the Go to section "Stopping the Machine". Engine". Go to "Adjusting the Throttle Cable". If the engine speed does not increase, your machine is ready for operation. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 28: Air Filter

    Insert filter in filter housing Attach filter cover Only use high-quality air filters so that the engine is protected from the entry of abrasive dust. Undo the fixing screws (1) FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 29: M-Tronic

    The machine can normally be operated in this temperature range with the shutter (2) in the summer position. Change the position of the shutter if necessary. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 30 Set the shutter (2) to the winter position. At temperatures above -10°C Remove the parts of the cover plate kit and refit the standard parts for summer operation. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 31: Electric Handle Heating

    This Leave the cap to one side. can result result in serious injuries or Pull off the spark plug boot (3). damage to property. Unscrew the spark plug. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 32: Engine Running Behavior

    (2) into the opening (3) of the hood. On the front, swivel the cap onto the hood, screw in the screw (4) and tighten. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 33: Sharpening Metal Cutting Blades

    – do checked by a dealer and re- not use a cleaning agent containing balanced as necessary – STIHL oil or grease. recommends a STIHL servicing dealer. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 34: Inspections And Maintenance By Dealer

    The guard may wear as a result of rubbing against the side plate of the harness during operation and should be replaced if necessary. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 35: Maintenance And Care

    Adjust electrode gap Spark plug Replace after every 100 hours of operation Visual inspection Cooling air intakes Clean Cylinder fins Clean FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 36 Tighten the screws for the muffler after a running time of 10 to 20 hours after commissioning see chapter "Inspection and Maintenance by Dealer", section "Antivibration Elements" FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 37: Minimize Wear And Avoid Damage

    Clutch – STIHL recommends that you have Filters (air, fuel) – servicing and repair work carried out Rewind starter – exclusively by an authorized STIHL FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 38: Main Parts

    13 Carrying strip 14 Choke knob 15 Manual fuel pump 16 Filter cover FS 490 17 Fuel tank 18 Switch for handle heating (option) 19 Wear guard Serial number FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 39: Specifications

    Fuel tank capacity: speed (cutting FS 410 C: 750 cc (0.75 l) attachment): 10,130 rpm FS 460 C: 750 cc (0.75 l) FS 490 C: 990 cc (0.99 l) FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 40 FS units include idling and rated for the vibration level. maximum speed with the same duration of exposure. For further details on compliance with Vibration Directive 2002/44/EC see www.stihl.com/vib. FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...

  • Page 41: Guide To Using This Manual 2 Maintenance And Repairs

    EN ISO 11806-1, EN 55012, EN 61000 - 6 - 1 FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 42 The year of manufacture and serial number are applied to the product. Done at Waiblingen, 03.02.2020 ANDREAS STIHL AG & Co. KG Dr. Jürgen Hoffmann Head of Product Data, Regulations and Licensing FS 410 C-M K, FS 460 C-M K, FS 490 C-M K...
  • Page 44 0458-748-0121-F englisch www.stihl.com *04587480121F* 0458-748-0121-F...

This manual is also suitable for:

Fs 490 c-mFs 460 c-m

Table of Contents

Save PDF