1. INTRODUCTION/ 2. SPECIFICATIONS INTRODUCTION TC0309 is a 4-channel digital thermometer for use with K-type thermo- couple as temperature sensor. Temperature indication follows National Bureau of Standards and IEC584 temperature/voltage table for K-type thermocouples. It internal memory can keep up to 16,000 records per channel.
3. SYMBOL DEFINITION AND BUTTON LOCATION : This indicates that the minus temperature is sensed. °C °F : Centigrade and Fahrenheit indication. : Thermocouple Type Indication. : The Maximum value is now being displayed. : The Minimum value is now being displayed. : This indicates auto power o is enabled.
Page 7
3. SYMBOL DEFINITION AND BUTTON LOCATION T1-T2 SETUP HOLD 9V BATTERY NEDA 1604 6F22 006P CLOCK INTV PLEASE READ MANUAL FOR SAFETY RANGE 1370 2498 OPEN POWER-UP OPTIONS K type temperature sensor T1 °C, °F control button to T4 input connector O set calibration screw LCD display Digital output connector...
4. OPERATION INSTRUCTIONS 4.1 POWER UP & TURN ON/OFF BACKLIGHT key turns the Thermometer ON or OFF and backlight ON & OFF. Press it once to turn on the Thermometer. Press it again for moment to turn ON or OFF backlight. Press and hold this button 3 second to turn OFF the power.
4. OPERATION INSTRUCTIONS 4.6 RECORD AND ERASE MEMORY OPERATION When one presses the "REC" button, the meter will start recording, and pressing the "REC" button again will stop recording, If you want to clear the memory, power o the meter, then press and hold “REC”...
4. OPERATION INSTRUCTIONS 4.8 RECORDING INTERVAL SETUP 1: press and hold “T1-T2” button and then power on the meter: 2: press “MAXMIN"(INTV) 3: press "REC" ▲or "°C/°F" ▼ to increase or decrease number, press “MAXMIN " (INTV) to adjust next item, then press “MAXMIN” (INTV) to nish.
4. OPERATION INSTRUCTIONS To exit the MAX/MIN mode, one may press and hold "MAX MIN" for two seconds. 4.10 AUTO POWER OFF By default, when the meter is powered on, it is under auto power o mode. The meter will power itself o after 30 minutes if no key operation and no RS232 communication combination at power on can disable auto power o .
4. OPERATION INSTRUCTIONS 4.13 DIGITAL OUTPUT The Digital Output is a 9600bps N 81 serial interface. The RX is a 5V normal high input port. The TX is a 5V normal high output port. P.11...
5. SETUP TESTLINK SE 309 RS232 INTERFACE SOFTWARE • THE TESTLINK PACKAGE CONTAINS 1. 80mm CD. 2. Custom designed RS232 cable for TestLink. • SYSTEM REQUIRED Windows 98/ NT 4.0/ NT2000/ XP/ VISTA. • MINIMUM HARDWARE REQUIRED PC or NoteBook with Pentium 90MHz or higher, 32 MB RAM ; At least 5 MB byte hard disk space available to install TestLink.
5. SETUP TESTLINK SE 309 RS232 INTERFACE SOFTWARE APPENDIX: THERMOCOUPLE PROBE SPECIFICATION Model Range Tolerances Description with Te on TP-K01 -50°C, to 200°C, ±2.2°C or ±0.75% tape insulation Bead probe Maximum -58°F to 392°F (±3.6°C or ±0.75%) insulating temperature : 260°C TP K01: probe for general condition measurements, especially for complex and...
Page 15
CUSTOMER SERVICE INQUIRIES Your emails are important to us so we strive to reply all hours. In exceptional cases, inquiries and emails within we may require more time to respond. Thank you for your understanding. For more information about our products and services, please send us an email: cs@perfectprime.com For B2B or project-based application, please send an email:...
Page 16
HORMES LIMITED Retailer cs@perfectprime.com Email G/F UNIT 3, 61 GLENTHORNE ROAD, Address LONDON W6 0LJ UNITED KINGDOM +44 203 7695377 Telephone...