TABLE OF CONTENTS Exchange of front and rear wheel Art. No. LS317 Page 3 Exchange of rear wheel mounting plate Art. No. LS323 Page 4 Art. No. LS328 Exchange of brake yoke Page 6 Exchange of brake housing and brake lever Art.
2. To replace the rear wheel, open the retaining ring (snap-ring) with replaced with a new one. pliers. Groove 4. Use the pliers to lock the new 5. Screw the fender and the wheel cap back in place. the axle. 3. www.trustcare.se...
(snap-ring) with a pliers. Groove 9. Use the pliers to lock the snap-ring 7. Remove the wheel from the old 8. Put the wheel on the new firmly into the groove on the axle. mounting plate mounting plate. 4. www.trustcare.se...
Page 5
See page 21 16. For right side Make a loop on the 18. Push the whole assembly into 17. Check the function of the brake. wire as above. Important! the rear leg and secure the Screw. See page 21 5. www.trustcare.se...
4. Remove the screw and open and assembly together with wire. the brake assembly. 6. Make a wire loop. 6. Secure the screws for the brake 7. Push together and secure with Important! assembly. See page 21 the screw. 6. www.trustcare.se...
8. Put on the new brake housing/ brake 6. Unmount the wire. 7. Pull out the handle tube from lever and screw on the two screws Important! the frame. See page 21 holding the brake housing. Important! See page 22-23. 7. www.trustcare.se...
Page 8
11. Screw together the brake Important! assembly. See page 21 13. Screw in the screw to secure the brake assemly 12. Insirt the rear brake assembly into the frame. to the frame. 14. Screw the height adjustment mechanism back in place. 8. www.trustcare.se...
B including the two ball bearings. 5. Mount the new bearing into the front leg of the 6. Push the front fork assembly in position rollator. and secure with the small screw. 9. www.trustcare.se...
5. Complete view of the disassembled seat. nuts and pull out the seat from the metal tubes. 6. Screw back the seat screws. Use an allen key for 5. Put back the seat strap in the key ring. indexing the fabric. 10. www.trustcare.se...
7. Insert the new brake wire and 8. Remove the old brake wire entirely 9. Insert the new wire in the handle reassembly. Important! from the frame and the handle. tube from bottom and up. See page 21 Important! See page 23-24 11. www.trustcare.se...
Page 12
10. Attach the wire to the adjustment as above. Important! assembly and rear wheel plate. screw and screw in the mechanism. See page 21 13. Push the rear wheel assembly 14. Secure with the screw. 15. Reassembly the height in place. adjustment parts. 12. www.trustcare.se...
6. Unscrew the screw on the handle 8. Remove the wire from the old 9. Put togheter the rearleg assembly, and pull out the brake mechanism. handle tube. Use the new handle Important! See page 21 and assembly. 13. www.trustcare.se...
Page 14
No: 2 – Nov 2019 10. Screw together the rear wheel 11. Push the rearwheel assembly 12. Mount the brake wire on the new assembly. in position. brake housing and secure the screws. 13. Screw the height adjustment mechanism back in place. 14. www.trustcare.se...
3. Mount the new linkage arm. On the left side the 4. Mount the parts using screws, washers, and nuts. hook for folding and the spring should also be mounted. 15. www.trustcare.se...
No: 2 – Nov 2019 2. The new height adjustment button consists of four 1. Unscrew screw A and remove the damaged height parts. adjustment. 3. Check that the holes in the plastic bushing, the frame and the handle tube correspond. 16. www.trustcare.se...
Page 17
3. Tighten the dome nut securely. Fix the nut with a drop of Loctite so it will not fall off. The metal sleeve serves as a fixture peg for the hook when the rollator is folded. 17. www.trustcare.se...
6. Put the fabric band into the slot in the unfold hook. and still fits smoothly into the slot in the linkage arm. Adjust the band so that the hook locks the rollator in open position and releases when you lift the seat in the middle opening. 18. www.trustcare.se...
9. Screw together the brake assembly 7. Left side, Wire first goes above (1) 8. Right side, Wire first goes above (1) and insirt it into the frame again. before going around the plastic part. before going around the plastic part. 21. www.trustcare.se...
Page 1. Disassembling the handle assemble 1. starting point 2. Disassemble the hightadjustment button. 3. Pull out the entire handle tube from the frame. 4. Unscrew the screws holding the brake housing. 23. www.trustcare.se...
Page 24
Page 2. Disassembling the handle assemble 5. Lower the brake housing. 6. Pull out the brake handle. 7. disconnect the brake wire. 8. Take out the bottom tube stopper and the brake wire connected to it. 24. www.trustcare.se...
Need help?
Do you have a question about the Let’s Shop and is the answer not in the manual?
Questions and answers