Advertisement
D,_L1;A
M I
-
The Delta 13 x 5" Thickness Planer is fully en
closed within its heavily ribbed fine grey iron castings
which provide minimum vibration and maximum ri
gidity between its working parts. This machine is
compact, ruggedly designed, has a large capacity and
is equipped for accurate work in cabinet, furniture,
sash, door and interior trim factories, contractors, box
manufacturers, pattern, job, woodworking and mainte
nance shops, schools and many other woodworking
and industrial plants and shops.
This machine will uniformly plane material up to
13" wide by 5" thick. It will take pieces as short as
6" long without requiring the use of a following block
and dress the stock as thin as 1/16" thick. The maxi
mum depth of cut is Ys" with a feed rate of 1 4 lineal
feet per minute. This means that 1 68" per minute will
be planed uniformly since the cutter head takes 75
cuts on each inch of material fed.
The overall dimensions of the machine are : 35"
wide, 26" deep and 39%" high.
The basic unit No. 22-1 0 1 consists of the following
standard parts: Base, right and left-hand columns,
table, safety type chip breaker, pressure bar and gear
box made of fine grey iron castings, safety type cutter
head complete with knife blades, ball bearings and
housings, matched set of 3 high-speed steel knife
blades, table rollers (idlers) , pOwer driven serrated in
feed and smooth out-feed rolls, gear box mechanism in
cluding a unique type clutch arrangement, 7" motor
pulley, matched set of 3 V-belts 68" long and wrenches.
The basic unit No. 22- 1 20 is the same as No. 22- 101
except that No. 22-1 20 is for 50 cycle current with No.
49-1 76 V-Belt and No. 22-1 05 8Yz" diameter pulley.
The motor, magnetic starters and electrical connec
tion from the starter to the motor are available and
can be purchased additional according to the cus
tomer's choice.
Accessories which may be purchased as additional
equipment are : 7" motor pulley No. 1 604, sub-base
including the motor mounting bracket No. 22- 1 02,
matched set of 3 high speed steel knife blades No.
22-104, 8Yz" motor pulley No. 22-1 05, knife grinding
attachment No. 22-1 06, jointing attachment No. 22-107 ,
3471,/'
one gallon can of lubricating oil for gear drive No.
22- 1 1 3,
diameter V-belt pulley No. 22- 1 1 4, 6"
shaving hood No. 22- 1 1 5, box of medium grit (No. 60)
aluminum oxide mounted grinding wheels No. 22- 1 1 6,
box of fine grit (No. 1 00) aluminum oxide mounted
grinding wheels No. 22-1 1 7, matched set of 3 V -belts
68" outside circumference for llse with 60 cycle 1 725
rpm motors No. 49-175, matched set of 3 V-belts 71"
outside circumference for use with 25 and 50 cycle
1425 rpm motors No. 49-176.
Machine Tools
5"
DELTA 13
X
and
Operating
22-8:
THICKNESS PLANER
Maintenance Instructions
Fig. 1. Delta 13
Refer to the photographs, drawings, and Table 1
to identify the parts mentioned in the following
structions.
CONSTRUCTION FEATURES
The base, right and left-hand columns, table, safety
type chip breaker, pressure bar and gear box are made
of fine grey iron castings to provide maximum rigidity
between the working parts and decrease vibrations to
a minimum to produce quiet smooth running operation.
The cutter head runs in two single row sealed and
shielded ball bearings which are prelubricated for their
entire life. It has 3 high-speed steel knife blades which
can be easily adjusted and securely locked in the dove
tail grooves of the cutter head. The cylindrical cutter
head body is made from stress-proof steel and its high
speed steel knife blades are ground to close tolerances
to assure proper balance. Large chip clearance is pro
vided by the maximum knife angularity in the cutter
head to assure the least possible amount of cutting
friction.
PM-1738
Revised:
Thickness Planer Instruction Manual
"Patents Pending"
5"
x
Thic:kness Planer.
1 0-17-51
111 -
Advertisement
