Delta 22-580 Instruction Manual
  1. Manuals
  2. Brands
  3. Delta Manuals
  4. Planer
  5. 22-580
  6. Instruction manual

Delta 22-580 Instruction Manual

13" two-speed finishing planer
Hide thumbs Also See for 22-580:
Table of Contents

Advertisement

Quick Links

28529
13" Two-Speed Finishing Planer
(Model 22-580)
PART NO. A05724 - 05-20-05
Copyright © 2005 Delta Machinery
To learn more about DELTA MACHINERY
RTD10000122AA
ESPAÑOL: PÁGINA 21
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
1-800-223-7278 (
1-800-463-3582).
please call
In Canada call

Advertisement

Table of Contents
loading

Related Manuals for Delta 22-580

Summary of Contents for Delta 22-580

  • Page 1 28529 13" Two-Speed Finishing Planer (Model 22-580) PART NO. A05724 - 05-20-05 Copyright © 2005 Delta Machinery To learn more about DELTA MACHINERY RTD10000122AA ESPAÑOL: PÁGINA 21 visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582).

  • Page 2: Table Of Contents

    NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery and we have advised you.

  • Page 3: Safety Guidelines

    SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

  • Page 4: General Safety Rules

    13. USE RECOMMENDED ACCESSORIES. The use of exposure, and wash exposed areas with soap and water. accessories and attachments not recommended by Delta may cause damage to the machine or injury to the user.

  • Page 5: Additional Specific Safety Rules

    ADDITIONAL SPECIFIC SAFETY RULES FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY. 14. ALLOW THE CUTTERHEAD TO REACH FULL SPEED DO NOT OPERATE THIS MACHINE until it is before feeding a workpiece. Changing speeds completely assembled and installed according to while planing can cause kickback.

  • Page 6: Grounding Instructions

    POWER CONNECTIONS A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug.

  • Page 7: Extension Cords

    FOREWORD The Delta Model 22-580 is a 13" (330mm) Portable Planer that has a cutting capacity of 13" (330mm) wide, 6½" (165mm) thick and 1/8" (3mm) deep. This machine has a powerful 15 amp 120 volt motor with a two-knife cutterhead.

  • Page 8: Carton Contents

    CARTON CONTENTS Fig. 2 13" Two-Speed Finishing Planer M5-16mm Hex Socket Head Screw M6-20 mm Hex Socket Head Screw Cutterhead Adjusting Handle Knife Transfer Tool Cutterhead Lock Handle Cutterhead Wrench and Handle Combination ASSEMBLY For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual.
  • Page 9 LOWERING THE EXTENSION TABLES The infeed and outfeed table extensions (A) Fig. 3 are shipped in the “UP” position on the machine. Lower both table extensions (A) to the "DOWN" position (Fig. 3). To check and adjust the top surface of the table extensions (A) level with the planer table, refer to the section of this manual entitled “LEVELING TABLE EXTENSIONS.”...

  • Page 10: Operation

    FASTENING PLANER TO SUPPORTING SURFACE During operation, if there is any tendency for the planer to tip over, slide or “walk” across the supporting surface, the planer must be secured to the supporting surface. Four holes (two of which are at (A) Fig. 9) are provided for this purpose.
  • Page 11 Make sure that the speed control is fully engaged before feeding work material. 1. The 22-580 is a two-speed planer. The speed control knob (A) is shown in Fig. 14. 2. Use the “Dimensioning” speed (B) Fig. 14 with 60 cuts per inch to size the board.

  • Page 12: Full Range Depth Stop

    FULL RANGE DEPTH STOP 1. You can use the depth stop (A) Fig. 15 to set the cutterhead to a pre-determined thickness. The stop can be set at any depth from 1/8" to 6-1/2" for repetitive planing. 2. To set the depth stop, lower the cutterhead to the desired depth.

  • Page 13: Leveling Table Extensions

    LEVELING TABLE EXTENSIONS For optimum performance, level the table extensions, one of which is shown at (A) Fig. 19, with the planer table. To check and adjust: DISCONNECT MACHINE FROM POWER SOURCE! 1. Place a straight edge (B) Fig. 19 on the planer table with one end of the straight edge extending out over the infeed table extension (A).
  • Page 14 MACHINE USE RECOMMENDED DEPTH OF CUT NOTE: One revolution of the cutterhead adjusting handle will Fig. 23 move the cutterhead up or down 1/16". 1/8" You can make an 1/8" depth of cut in soft woods up to 6" wide and in hard woods up to 4"...

  • Page 15: Troubleshooting

    Fig. 27 TROUBLESHOOTING For assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call the DELTA Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582).

  • Page 16: Maintenance

    MAINTENANCE REPLACING KNIVES The knives supplied with your planer are double edged and reversible so that you can turn the knives end-for-end when one edge becomes dull or chipped. To change the knives: DISCONNECT MACHINE FROM POWER SOURCE! Remove the two top covers (C) Fig. 28. Raise the head assembly (B) to 4"...
  • Page 17 8. Reverse the knife (H) Fig. 32 or install a new knife. Position the magnetized knife transfer tool (G) on top of knife. Place the knife in the cutterhead underneath the locking bar (D) with the bevel edge up. Ensure that the pins in the cutterhead and locking bar engage with the holes in the knife.

  • Page 18: Lubrication

    LUBRICATION To periodically lubricate the gears in the gear box, the feed roller bushings, and the spindles and columns: DISCONNECT TOOL FROM POWER SOURCE! 1. Remove the two top covers (A) Fig. 36. 2. Remove the screw (B) Fig. 38. Remove the depth stop assembly. 3.

  • Page 19: Service

    SERVICE PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network • of Porter-Cable Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

  • Page 20: Warranty

    Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.

  • Page 21: Español

    Fax: (519) 767-4131 Fax: (604) 420-3522 Fax: (514) 336-3505 The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ®...

Table of Contents