Black+Decker BES700 Instruction Manual
  1. Manuals
  2. Brands
  3. Black+Decker Manuals
  4. Saw
  5. BES700
  6. Instruction manual

Black+Decker BES700 Instruction Manual

Hide thumbs Also See for BES700:
Table of Contents

Advertisement

Quick Links

www.blackanddecker.com.au
www.blackanddecker.co.nz
BES700
BES710

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BES700 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Black+Decker BES700

Summary of Contents for Black+Decker BES700

  • Page 1 BES700 www.blackanddecker.com.au BES710 www.blackanddecker.co.nz...
  • Page 6 12 11...

  • Page 7: Intended Use

    (Original instructions) ENGLISH Intended use Your BLACK+DECKER BES700, BES710 sliding compound mitre saw has been designed for sawing wood, plastic and nonferrous metal only. This tool is intended for non profes- sional users. Safety instructions General power tool safety warnings...

  • Page 8: Safety Instructions For Mitre Saws

    English (Original instructions) (Original instructions) ENGLISH b. Avoid body contact with earthed or grounded allow you to become complacent and ignore tool surfaces such as pipes, radiators, ranges and safety principles. A careless action can cause severe refrigerators. There is an increased risk of electric shock injury within a fraction of a second.

  • Page 9: Additional Safety Instructions For Mitre Saws

    (Original instructions) ENGLISH studs, etc. Abrasive dust causes moving parts such as the Plan your work. Every time you change the bevel or lower guard to jam. Sparks from abrasive cutting will mitre angle setting, make sure the adjustable fence burn the lower guard, the kerf insert and other plastic parts.
  • Page 10 Ensure that any spacers and spindle rings used are This mitre saw has been designed for sawing wood, suitable for the purpose as stated by BLACK+DECKER. plastic and nonferrous metal only. Do not use the saw Repairs to the cut line guidance system should be carried...

  • Page 11: Residual Risks

    If the supply cord is damaged, it must be replaced by the comparing one tool with another. manufacturer or an authorised BLACK+DECKER Service The declared noise emission values may also be used in a Centre in order to avoid a hazard.
  • Page 12 (Original instructions) ENGLISH 2. Bevel lock knob Table extension rail (Fig. C & D) 3. Support stand Your mitre saw is supplied with 2 table extension rails (5) to 4. Work piece clamp support long overhanging workpieces. 5. Table extension rail Pull the table extension rail (5) to the required length for 6.

  • Page 13: Removing The Blade

    (Original instructions) ENGLISH Changing or installing a new saw blade (Fig. I, Cutting depth If you want to cut a groove you can set the depth of cut J, K) using the depth of cut screw (29). Warning! To reduce the risk of serious personal injury, turn Turn the depth of cut screw (29) and fix with the counter off the tool and disconnect it from the power source before nut.
  • Page 14 (Original instructions) ENGLISH The Cut line System is independent of the mitre saw’s trigger than 152 mm from the blade. Hold the workpiece tightly to switch. the table and the fence when cutting. Keep hands in position until the trigger has been released and the blade has The light does not need to be on in order to operate the saw.

  • Page 15: Cutting Crown Molding

    33.9° against fence vertically against the Fence 2. Miter table set left 31.6° BES700 - 70 mm for 216 mm 3. Save left end of cut BES710 - 90 mm for 254 mm LEFT SIDE, OUTSIDE Position material as shown in Figure R All cuts should be...

  • Page 16: Troubleshooting

    (Original instructions) ENGLISH moldings are very precise and difficult to set exactl . Since To clear the guard over the wood, with the saw off and your they can easily shift slightly and very few rooms have exactly right hand on the operating handle, place your right thumb square corners, all settings should be tested on scrap outside of the upper portion of the guard and roll the guard up molding.

  • Page 17: Ec Declaration Of Conformity

    Max mitre capacity at 45 ° Max. dept cut at 90 ° Max. dept cut at 45 ° BES700-Level of sound pressure according to EN 62841: (sound pressure) 97.5 dB(A), Uncertainty (K) 3 dB(A) (sound power) 108.0 dB(A), Uncertainty (K) 3 dB(A) BES710-Level of sound pressure according to EN 62841: (sound pressure) 96.0 dB(A), Uncertainty (K) 3 dB(A)
  • Page 18 Australia & New Zealand Stanley Black & Decker www.blackanddecker.com.au www.blackanddecker.co.nz Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ)
  • Page 20 N632712 02/2019...

This manual is also suitable for:

Bes710

Table of Contents

Save PDF