Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cervis SmaRT DIN-9H1R5
Summary of Contents for Cervis SmaRT DIN-9H1R5
- Page 1 ™ SmaRT DIN-9H1R5 Base Unit User Manual U082.0.2 DIN-9H1R5 ©2020 Cervis, Inc.
- Page 2 This document is the property of Cervis, Inc. and cannot be copied, modified, e-mailed, or reproduced without the express prior written consent of Cervis, Inc. Cervis, Inc. reserves the right to change this manual or edit, delete, or modify any information without prior notification.
-
Page 3: Table Of Contents
List of Figures ..........................i List of Tables ..........................i Cervis, Inc. Safety Precautions ....................1 1.0 SmaRT DIN-9H1R5 Base Unit ..................... 2 2.0 SmaRT DIN-9H1R5 Installation ................... 3 2.1 DIN-9H1R5 Base Unit Mounting Dimensions ..............3 2.2 External Antenna Mounting ..................... 4 2.3 SmaRT DIN-9H1R5 Terminal Connections .............. - Page 4 Electrical circuit used to suppress electrical spikes (transients) by diverting excess current around the protected device. RS-232 Low-speed serial interface used for configuration of the base unit. SmaRT Connect Cervis software that allows a base unit to be configured through the base unit RS-232 port. U082.0.2 DIN-9H1R5...
-
Page 5: Cervis, Inc. Safety Precautions
Base Unit Manual Cervis, Inc. Safety Precautions ✓ Read and follow all instructions. ✓ Failure to abide by Safety Precautions may cause equipment failure, loss of authority to operate the equipment, and personal injury. ✓ Use and maintain proper wiring. Follow equipment manufacturer instructions. -
Page 6: Smart Din-9H1R5 Base Unit
SmaRT DIN-9H1R5 1.0 SmaRT DIN-9H1R5 Base Unit The SmaRT DIN-9H1R5 Base Unit for industrial control systems features one Form C and five Form A relay outputs. Each Form C relay contact can switch a resistive load of 10 A max. @ 250 VAC/30 VDC. -
Page 7: Smart Din-9H1R5 Installation
Base Unit Manual 2.0 SmaRT DIN-9H1R5 Installation Make sure the machine on which the base unit is to control is disabled during installation. The base unit enclosure and connectors are NOT rated for high pressure washing. Doing so could damage the base unit or connectors. -
Page 8: External Antenna Mounting
SmaRT DIN-9H1R5 2.2 External Antenna Mounting 183 mm (7.2") BB3-06 900 MHz Antenna and AA7-07 Extension/Adapter Figure 3. External Antenna Mounting Details U082.0.2 DIN-9H1R5... -
Page 9: Smart Din-9H1R5 Terminal Connections
Base Unit Manual 2.3 SmaRT DIN-9H1R5 Terminal Connections Terminal 6: K1 Normally Closed K1 NC Terminal 5: K1 Common K COM K COM K1 COM Terminal 4: K1 Normally Open 12VDC K1 NO Terminal 3: Terminal 2: Terminal 1: Terminal 9: K Common –... -
Page 10: Smart Handheld Remote To Din-9H1R5 Communications
Table 2. Compatible DIN-9H1R5 External Antenna Details Part Cervis # 900 MHz IS BAND Swivel Antenna BB3-06 3-ft. antenna extension/adapter cable RP-SMA Plug to RP-TNC Jack AA7-07 ✓ Note: Use only the antenna recommended by Cervis, Inc. with the SmaRT base unit. U082.0.2 DIN-9H1R5... -
Page 11: Smart Din-9H1R5 Specifications
Base Unit Manual 6.0 SmaRT DIN-9H1R5 Specifications Table 3. SmaRT DIN-9H1R5 Specifications SmaRT DIN-9H1R5 Specs Power +7 to +32 VDC Radio Frequency 906–924 MHz RF Power 10 mW License License Free Modulation Channel-Hopping DSSS Antenna Internal or External –25° C to 60° C (–13° F to 140° F) -
Page 12: Appendix A: Exposure To Radio Frequency Energy
A SmaRT base unit when active sends out radio frequency (RF) through its external antenna. Base units using an external antenna should be mounted to ensure the antenna is at least 20cm away from the human body. Only the external antenna recommended by Cervis, Inc. is to be used (see Table 2). -
Page 13: Appendix C: Typical Handheld To Base Unit Communication
Base Unit Manual Appendix C: Typical Handheld to Base Unit Communication Handheld remote and base unit communications are established at Cervis, Inc. before shipping when systems are ordered. However, it may be necessary to establish or re-establish communication between a remote and a base unit at some point. The Associate procedure does this. -
Page 14: Figure 6. Associate/Dissociate Buttons
SmaRT DIN-9H1R5 7. TX begins to slowly blink. Continue to hold B1. 8. Apply power to the base unit. Associate to Dissociate The handheld and base unit begin to establish base unit from a communication link while the Associate base unit button is held. -
Page 15: C2: Din-9H1R5/Cb Remote Communication
4. Observe the LEDs. When the TX LED begins to blink, power up the base unit while continuing to hold S13 and S12. When the TX, RX, ERR, and BAT LEDs light solid, release S13 and S12. ©2020 Cervis, Inc. - Page 16 SmaRT DIN-9H1R5 Note: Be aware that all remote associations to the base unit are now broken. U082.0.2 DIN-9H1R5...
-
Page 17: C3: Din-9H1R5/Mcb Remote Communication
4. Observe the LEDs. When the TX LED begins to blink, power up the base unit while continuing to hold S1 and the Power button. When all four LEDs light solid, release S1 and Power Button. Association is successful when the TX and RX LEDs rapidly flash in unison. ©2020 Cervis, Inc. -
Page 18: Figure 8. Mcb Switch Actuation For Associate And Dissociate
SmaRT DIN-9H1R5 ASSOCIATE Pull Pull Power ON DISSOCIATE Figure 8. MCB Switch Actuation for Associate and Dissociate To Dissociate (see Figure 8) The MCB remote must be OFF and the base unit must have power removed before the Dissociation process can be started. -
Page 19: C4: Din-9H1R5/Pg Remote Communication
4. Observe the LEDs. When the TX LED begins to blink, power up the base unit while continuing to hold S1 and S7. When all four LEDs light solid, release S1 and S7. Note: Be aware that all remote associations to the base unit are now broken. ©2020 Cervis, Inc. -
Page 20: C5: Din-9H1R5/Xx-218 Remote Communication
SmaRT DIN-9H1R5 C5: DIN-9H1R5/XX-218 Remote Communication CAUTION To prevent inadvertent machine movement, be sure to remove power from the Base Unit before attempting to Associate or Dissociate. To Associate (see Figure 10) Associate mode establishes the communications link between the 18-button handheld remote and base unit on a 1-to-1 basis. -
Page 21: Figure 11. Xx-218 Dissociate Mode
5. Press and release button 17. The GREEN LED1 and the RED LED3 turn ON. 6. Power up the base unit. If dissociation is successful, the green LED1 (TX) on the handheld remote continually flashes, indicating that the handheld and the base unit are not communicating. ©2020 Cervis, Inc. - Page 22 SmaRT DIN-9H1R5 ™ www.cervisinc.com Visit our Web site at: ©2020 Cervis Inc. All rights reserved. Content is subject to change without notice. U082.0.2 DIN-9H1R5...