Related Manuals for Cervis SmaRT BU-9H16AF-8F-8V-RS
Summary of Contents for Cervis SmaRT BU-9H16AF-8F-8V-RS
- Page 1 ™ ™ BU-9H16AF-8F-8V-RS Base Unit User Manual DN: U064.1-SmaRT_BU-9H16AF-8F-8V-RS 2011 Cervis, Inc.
- Page 2 This document is the property of Cervis, Inc. and cannot be copied, modified, e-mailed, or reproduced without the express prior written consent of Cervis, Inc. Cervis, Inc. reserves the right to change this manual or edit, delete, or modify any information without prior notification.
-
Page 3: Table Of Contents
5.0 Specifications ........................11 List of Figures Figure 1. SmaRT BU-9H16AF-8F-8V-RS-INT Base Unit .............. 2 Figure 2. SmaRT BU-9H16AF-8F-8V-RS with SmaRT Remote Control Units ......3 Figure 3. SmaRT BU-9H16AF-8F-8V-RS-INT Mounting Dimensions ......... 4 Figure 4. SmaRT BU-9H16AF-8F-8V-RS-EXT Mounting Dimensions ........5 Figure 5. -
Page 4: Related Documents
TX/RX Transmit/Receive Related Documents System related Cervis, Inc. Engineered System Approval document Appropriate SmaRT remote control user manual Documentation provided by Cervis on delivery Contact Cervis, Inc. with questions during installation or troubleshooting at (724) 741-9000 U064.1-SmaRT_BU-9H16AF-8F-8V-RS... -
Page 5: Cervis Inc. Safety Precautions
900MHz Base Unit Manual Cervis Inc. Safety Precautions Read and follow all instructions. Failure to abide by Safety Precautions may result in equipment failure, loss of authority to operate the equipment, and personal injury. Use and maintain proper wiring. Follow equipment manufacturer instructions. -
Page 6: Bu-9H16Af-8F-8V-Rs Base Unit
The SmaRT™ BU-9H16AF-8F-8V-RS features sixteen FET, high side switching outputs or switch-to-ground digital inputs. The versatile, programmable digital inputs/outputs can be customized by Cervis to fit specific user applications. The BU-9H16AF-8F-8V-RS accepts a broad range of input power with operating voltages ranging from +10VDC to +30VDC. The wiring harness consists of two uniquely keyed connectors for P1 and P2 of the base unit that when properly wired to controlled devices effectively eliminates the risk of cross connections. -
Page 7: Smart Bu-9H16Af-8F-8V-Rs In Smart Remote Control Systems
SmaRT remote without opening the enclosure of either device. Association processes for each remote control unit are described in detail in each SmaRT remote manual, Cervis Engineering SpecSheets, and the documentation provided to you with your system. PG-914... -
Page 8: Bu-9H16Af-8F-8V-Rs Base Unit Installation
Base Units subjected to the elements must be vertically installed. Cervis recommends installing all base unit top-side UP (vertical) Use the configuration diagrams supplied by Cervis as a guide when mounting the base unit and connecting the wiring harnesses. Dimensions for drilling mounting holes are shown in Figure 3 and Figure 4. -
Page 9: Smart Bu-9H16Af-8F-8V-Rs-Ext
183mm (7.2”) 7.4mm BU-9H16AF-8F- 8V RS EXT (0.29”) dia. 102mm (4”) 35.87mm center-to-center (1.412”) 118mm (4.7”) Figure 4. SmaRT BU-9H16AF-8F-8V-RS-EXT Mounting Dimensions 2011 Cervis, Inc. -
Page 10: Optional Antenna Extension Kit Installation
SmaRT BU-9H16AF-8F-8V-RS 2.1.3 Optional Antenna Extension Kit Installation Make sure the antenna is located in clear line-of-sight of the remote. 1. Loosen and remove extension cable nut to allow the antenna ferrule to push through a mounting hole (user discretion). -
Page 11: Smart Bu-9H16Af-8F-8V-Rs Wiring
900MHz Base Unit Manual 2.1.4 SmaRT BU-9H16AF-8F-8V-RS Wiring Use the configuration diagrams supplied by Cervis as a guide when connecting the wiring harness P1 and P2 connections. Table 1 is a simplified wiring guide for two typical types of Cervis wiring harnesses. P1 Grey connector BB6-01 (HN-1001) and P2 black connector BB7-03 (HN-1002), each 12-wire cables, are numbered—marked from 1 to 11—with the last wire... -
Page 12: Figure 6. Bu-9H16Af-8F-8V-Rs P1 And P2 Field Wiring
SmaRT BU-9H16AF-8F-8V-RS LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD Figure 6. BU-9H16AF-8F-8V-RS P1 and P2 Field Wiring U064.1-SmaRT_BU-9H16AF-8F-8V-RS... -
Page 13: Associate Mode
Communication between the SmaRT BU-9H16AF-8F-8V-RS and SmaRT remotes is established for systems before shipped from Cervis. There may be occasions when the communication link between remote and base unit will have to be established in the field. Access to and the exact button or switch sequencing for the remote used while in Associate mode will vary depending on the type of SmaRT remote with which the base unit is to communicate. -
Page 14: Available Options
The following are some of the options available for the BU-9H16AF-8F-8V-RS-INT and BU- 9H16AF-8F-8V-RS-EXT base units. For custom configuration of your particular base unit and system, please consult with your Cervis Inc. sales representative. Table 2. Available Options Part Number... -
Page 15: Specifications
900MHz Base Unit Manual 5.0 Specifications Table 3. SmaRT BU-9H16AF-8F-8V-RS Specifications Item Description Power +10 to +30VDC 906 – 924MHz or Frequency 2405-2480MHz (option) RF Power 10mW (max.) Radio License License Free (disabled) Modulation DSSS Internal or Antenna External (option) Operating Temp -20°C to 55°C (-4°F to 131°F) - Page 16 SmaRT BU-9H16AF-8F-8V-RS U064.1-SmaRT_BU-9H16AF-8F-8V-RS...
- Page 17 900MHz Base Unit Manual www.cervisinc.com Visit our Web site at: 2011 Cervis, Inc. All rights reserved. Content is subject to change without notice. 2011 Cervis, Inc.