Kaya Instruments JetCam Quick Start Manual
High speed camera
Hide thumbs
Also See for JetCam:
- Quick troubleshooting manual (8 pages) ,
- Manual (10 pages) ,
- User manual (58 pages)
Table of Contents
Advertisement
Quick Links
High Speed Camera Quick Start Guide
January
International Distributors
JetCam
(Part-No. KY-JetCam)
201
9
Sky Blue Microsystems GmbH
Geisenhausenerstr. 18
81379 Munich, Germany
+49 89 780 2970, info@skyblue.de
www.skyblue.de
In Great Britain:
Zerif Technologies Ltd.
Winnington House, 2 Woodberry Grove
Finchley, London N12 0DR
+44 115 855 7883, info@zerif.co.uk
www.zerif.co.uk
Advertisement
Table of Contents
Related Manuals for Kaya Instruments JetCam
Summary of Contents for Kaya Instruments JetCam
- Page 1 JetCam High Speed Camera Quick Start Guide (Part-No. KY-JetCam) January International Distributors In Great Britain: Sky Blue Microsystems GmbH Zerif Technologies Ltd. Winnington House, 2 Woodberry Grove Geisenhausenerstr. 18 81379 Munich, Germany Finchley, London N12 0DR +49 89 780 2970, info@skyblue.de +44 115 855 7883, info@zerif.co.uk...
-
Page 2: Table Of Contents
QSFP+ installation and connectivity ..................9 JetCam installation and connectivity ..................9 Vision Point Application installation ..................10 Using JetCam Camera ....................... 11 Selecting a Grabber board ......................11 Detecting the JetCam camera ....................11 Starting and controlling acquisition ..................12... -
Page 3: Figures And Tables
Figures and Tables Figures 1 : J ..............7 IGURE AMERA SYSTEM STRUCTURE DIAGRAM 2 : QSFP+ M ......................... 9 IGURE ODULE 3 : QSFP+ M ..............9 IGURE ODULE WITH FIBER CABLE INSERTED 4 : J ................. 9 IGURE AM CAMERA POWER CONNECTOR 5 : J ............ -
Page 4: Introduction
Introduction 3.1 Safety Precautions With your JetCam camera in hand, please take a minute to read carefully the precautions listed below in order to prevent unnecessary injuries to you or other personnel or cause damage to property. Before using the product, read these safety precautions carefully to assure correct use. -
Page 5: Disclaimer
Even if the product is used properly, KAYA Instruments assumes no responsibility for any damages caused by the following: - Earthquake, thunder, natural disaster or fire resulting from the use beyond our responsibility, acts caused by a third party or other accidents, the customer’s willful or... - Page 6 Introduction KAYA Instruments assumes no responsibility or liability for: - Erasure or corruption of data arising from use of this product. - Any consequences or other abnormalities arising from use of this product, or damage of this product not due to our responsibility or failure due to modification.
-
Page 7: System Description
System Description 4.1 System Components The JetCam system configuration includes the following parts: JetCam Camera Integrated lens 3G SDI output for local monitor Komodo Fiber Frame Grabber 12V Power Supply QSFP+ Modules High Speed Camera Quick Start Guide... -
Page 8: Figure 1 : Jetcam Camera System Structure Diagram
System Description Fiber Cable Vision Point Software and SDK Table 1 : JetCam Camera system components Example of the system connectivity is described in Figure 1. Figure 1 : JetCam Camera system structure diagram High Speed Camera Quick Start Guide... -
Page 9: Installation And Connectivity
Komodo Fiber board Fiber QSFP+ Modules Fiber optic cable NOTE: KAYA Instruments doesn’t guarantee compatibility with all computers that have the above specifications. Please, consult KAYA representative for any specific issue 5.2 Komodo board installation 1. Before installing the Komodo Board, turn off the power of the computer and its peripherals. -
Page 10: Qsfp+ Installation And Connectivity
For detailed information about QSFP+ installation please refer to JetCam User Guide documentation. 5.4 JetCam installation and connectivity Connect the Power Adaptor to the JetCam power supply connector as shown in Figure 4. QSFP+ Connector NC GND... -
Page 11: Vision Point Application Installation
Detecting the camera using Vision Point application will turn off the SDI output and the image will be displayed only via Vision Point application interface. For SDI output, the camera should be powered cycle. A typical JetCam system is connected as described in the figure below. Komodo Fiber Frame Grabber... -
Page 12: Using Jetcam Camera
Using JetCam Camera The Vision Point application is the main interface for all JetCam camera setting and configurations. The basic steps include: 1. Selecting a grabber board 2. Opening, creating and closing a project 3. Adjusting the grabber parameters 4. Scanning and adjusting the camera parameters 5. -
Page 13: Starting And Controlling Acquisition
Using JetCam Camera Figure 7 : JetCam description parameters 6.3 Starting and controlling acquisition After JetCam camera was detected, the stream acquisition can commence. In order to start the acquisition, press the button, located in the main toolbar. At this point the picture window will open, showing the current stream parameters in the bottom of the window, and the stream will commence. -
Page 14: Figure 8 : Vision Point App Main Window
Using JetCam Camera The Vision Point App main window with all of its components shown in Figure 8. Figure 8 : Vision Point App main window The basic components of the application are: 1. The toolbar Menu: Includes project operation buttons, hardware selection and stream acquisition control buttons. - Page 15 Using JetCam Camera 3. The acquisition picture window: Displays the last frame that has been grabbed. Information on frame rate and image format can be found at the bottom of the picture window. 4. The system messages window: Displays general, runtime informational and error messages regarding the state of stream grabbing and changes to various components.