FORM FIT HD 1C 06 Installation Instructions

FORM FIT HOOD PROTECTOR
Acura CSX 2006 -
Thank you for purchasing a form fit hood protector.
Care Instructions
Clean the protector with a mild soap and water solution or plastic cleaner only.
Periodically check to make sure all the hardware is in place and the protector is secure.
Attention!
Do not use chemicals or solvents. Avoid using automatic car washes. Do not pull on the
protector when opening or closing the hood.
Hardware Kit
x 3 x 3 x 3
Tools Required
Installation Instruction
1. Be sure that the hood is clean and dry inside and out. Release the hood, but do not open it
Install the bumpons as shown in Illustration #1. Attention: The bumpons must be installed on the hood
2.
not the protector!!!! If the bumpons are installed on the protector, they will wear through the paint.
3. Center the protector on the hood, resting on the bumpons.
Peel and fold an anti-abrasion film pad in half over the edge of the hood, underneath each of the three (3)
4.
holes in the protector. See Illustrations #1 & #2 - Step 4.
5a) Place a clip over each of the anti-abrasion film pads on the edge of the hood as shown below in
Illustration #2 – Step 5a.
b) Insert a pin through the protector into each of the clips. See Illustration #2 – Step 5b.
c) Insert a #6 x 5/8'' screw through an 'L'- bracket and into the clip. See Illustration #2 – Step 5c & 5d.
d) Make sure all the components are well seated together; the protector is centered on the hood, and then
tighten the screws into the clips.
6. On some vehicles it may be necessary to adjust the hood bumpers and/or latch for proper clearance.
Note: Do not pull on the protector when opening or closing the hood.
Illustration # 1: Bumpon Location and Clip Placement
20"
3 ½"
Illustration # 2: Clip Configuration – Patent No. 6,892,427
Step #4 Step #5a
Made in Canada
#6 x 5/8''
Screws
x 3 x 3 x 3
#
2
20"
4"
Clips Placement
Step #5b
Step #5c & 5d
FORM FIT HOOD PROTECTOR
Acura CSX 2006 -
HD 1C 06
Thank you for purchasing a form fit hood protector.
Care Instructions
Clean the protector with a mild soap and water solution or plastic cleaner only.
Periodically check to make sure all the hardware is in place and the protector is secure.
Attention!
Do not use chemicals or solvents. Avoid using automatic car washes. Do not pull on the
protector when opening or closing the hood.
Hardware Kit
'L'
Bracket
x 3
Tools Required
Installation Instruction
.
1. Be sure that the hood is clean and dry inside and out. Release the hood, but do not open it
2. Install the bumpons as shown in Illustration #1. Attention: The bumpons must be installed on the hood
not the protector!!!! If the bumpons are installed on the protector, they will wear through the paint.
3. Center the protector on the hood, resting on the bumpons.
4. Peel and fold an anti-abrasion film pad in half over the edge of the hood, underneath each of the three (3)
holes in the protector. See Illustrations #1 & #2 - Step 4.
5a) Place a clip over each of the anti-abrasion film pads on the edge of the hood as shown below in
Illustration #2 – Step 5a.
b) Insert a pin through the protector into each of the clips. See Illustration #2 – Step 5b.
c) Insert a #6 x 5/8'' screw through an 'L'- bracket and into the clip. See Illustration #2 – Step 5c & 5d.
d) Make sure all the components are well seated together; the protector is centered on the hood, and then
tighten the screws into the clips.
6. On some vehicles it may be necessary to adjust the hood bumpers and/or latch for proper clearance.
Note: Do not pull on the protector when opening or closing the hood.
Illustration # 1: Bumpon Location and Clip Placement
Illustration # 2: Clip Configuration – Patent No. 6,892,427
Step #4
Rev1.100129 Made in Canada
x 3 x 3 x 3 x 3
#
2
20"
20"
3 ½"
4"
Clips Placement
Step #5a Step #5b
HD 1C 06
'L'
#6 x 5/8''
Bracket
Screws
x 3
.
Step #5c & 5d
Rev1.100129