herrmann HL 60 Series Technical Information, Assembly And Operating Instructions page 35

The following parts are not illustrated:
Designation
Cable
Cable for firing unit - ignition unit
Cable for firing unit - motor
Cable set (firing unit Euro plug with connector for photo
conductive cell and connecting plug for oil pre-heater)
Cable for firing unit - magnetic coil
Cable for ignition unit - ignition electrode with resistor
Cable for connecting plug - oil pre-heater
Cable bridge
Screws
Hexagon nut DIN 934 M6 for burner housing,
connection flange and unit flange
Hexagon nut DIN 934 M8 for sliding flange for burner,
sliding flange for boiler,
connection flange and unit flange
Flat headed screw with DIN 923 M5x2.5x6 slot
for nozzle block cover
Cylinder head screw with DIN 912 M5x12
hexagon socket for nozzle block cover and pump
Thread-rolling screw DIN 7500 CM 3x16 for Euro plug
Cylinder head screw with SW4 hexagon socket
similar to DIN 7984 M8x30 for sliding flange for burner,
sliding flange for boiler and unit flange
Cylinder head screw with SW4 hexagon socket
similar to DIN 7984 M8x22 for housing cover
Countersunk screw with DIN 7991 M6x16
hexagon socket for base plate and mini base plate
Slotted pan head screw with cross slot DIN 7981
C2.9x13 for clamping piece
Countersunk flat head tapping screw with cross slot
DIN 7982 C3.5x16 for bearing housing
Cylinder head screw with DIN 912
internal hexagon socket M5x16 for air inlet
Cylinder head screw with SW4 hexagon socket
similar to DIN 7984 M4x10 for motor,
holder for photo conductive cell and retaining ring
Thread-rolling screw DIN 7500 CM 4x8
for plug base for firing unit
Thread-rolling screw DIN 7500 CM 4x40
for ignition unit
Cylinder head screw with DIN 912
internal hexagon socket M6x45 for connection flange
DIN 125-1 8.4x16x1.6 disk for sliding flange for burner,
sliding flange for boiler and unit flange
Cylinder head screw with DIN 912
internal hexagon socket M5x8 for baffle plate
Countersunk screw with crossed slot DIN 965 M3x5
for retaining ring seal
Cylinder head screw with DIN 912
internal hexagon socket M5x14 for holder for
ignition electrode block and air intake adapter
Threaded pin with flat point and hexagon socket
DIN 913 M6x5 for blower wheel
Cylinder head screw with SW4 hexagon socket
similar to DIN 7984 M8x13 for sliding flange for burner
DIN 440 6.6 disk for burner pipe
Cylinder head screw with DIN 912
internal hexagon socket M4x100 for silencer housing
Flat headed screw with DIN 923 M6x4x9 slot
for connection flange and unit flange
Cylinder head screw with SW4 hexagon socket
similar to DIN 7984 M8x22, service screw
Hexagon socket screw with SW4 hexagon socket
similar to DIN 931 M8x22, service screw
Part no. Designation
Flange screw with SW4 hexagon socket similar to
ISO 7380 M6x10 for burner pipe, mini base plate
10013.00092
and base plate
10013.00003
Countersunk flat head tapping screw with cross slot
DIN 7982 C2.9x18 for air controller holder
10013.00004
Cylinder head screw with SW4 hexagon socket
10013.00002
similar to DIN 912 M4x18 for cover
10013.00009
Cylinder head screw with SW4 hexagon socket
10013.00016
similar to DIN 912 M4x50 for intake silencer
10013.00032
Allen wrench
10023.00001
10023.00002
10023.00003
10023.00004
10023.00007
10023.00008
10023.00009
10023.00010
10023.00011
10023.00012
10023.00014
10023.00016
10023.00017
10023.00018
10023.00019
10023.00020
10023.00038
10023.00043
10023.00055
10023.00061
10023.00063
10023.00084
10023.00087
Important:
10023.00091
Please only use original Herrmann spare parts, since otherwise the
guarantee is null and void (see guarantee conditions). When ordering
spare parts, please specify the designation and order number of your
10023.00093
burner.
10023.00094
Subject to technical changes.
EN
35
Part no.
10023.00151
10023.00155
10023.00184
10023.00187
10031.00001