BWI Eagle AIR-EAGLE SR PLUS 36-4000-DC Product Information Bulletin

AIR-EAGLE
2.4 GHz RF Transceiver
MODEL 36-4000-DC – Rev.3
DESCRIPTION
The A -E SR PLUS RF T
IR AGLE RANSCEIVER IS
transmit and receive unique signals from an identical unit located up to
1200 feet away. This model comes equipped with four contact inputs and
four high current SPDT relay outputs. This allows the user to not only
transmit information out, but receive a confirming signal back that the
operation was performed. The Air-Eagle SR PLUS TRX is user-
programmable for up to 128 digital addresses and eight network
frequencies to allow multiple transceivers to operate simultaneously in the
same area and utilizes spread-spectrum technology and provides the
utmost security and reliability even in the noisiest RF environments. A
terminal strip has been provided for interfacing with external dry contact
inputs as well as dry contact relay outputs. This unit can operate remote
machinery such as pumps, gates, chutes etc.
INSTALLATION
DISCONNECT DC Power from all equipment before installation.
1. Mount the A -E SR PLUS T
IR AGLE
location.
2. Install antenna. The unit has an antenna connector located on the
right side on the enclosure. Attach the supplied portable antenna to
this connector.
3. Connect DC power and control to the proper terminals in your control
circuit.
TERMINAL STRIP WIRING – BOTTOM PCB
1 N/O Relay #1 7 N/O Relay #3
2 C Relay #1 8 C Relay #3
3 N/C Relay #1 9 N/C Relay #3
4 N/O Relay #2 10 N/O Relay #4
5 C Relay #2 11 C Relay #4
6 N/C Relay #2 12 N/C Relay #4
TERMINAL STRIP WIRING –TOP PCB
1 N/O Input #1
2 C Input #1
3 N/O Input #2
4 C Input #2
5 N/O Input #3
6 C Input #3
238 Pillow Street
Butler, PA 16001
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
®
SR PLUS
a four I/O unit designed to
in a convenient
RANSCEIVER
13 (-) 9-36 VDC INPUT
14 (+) 9-36 VDC INPUT
7 N/O Input #4
8 C Input #4
9 Not Used
10 Not Used
PRODUCT INFORMATION
BULLETIN
Dimensions (with mounting plate) 6.3" L x 4.8" W x 4.3" H
DIGITAL ADDRESS & FREQUENCY SET-UP
This transceiver is factory programmed to Frequency #1 and Digital
Address "0". These settings can be changed by the user in any
combination but must match its corresponding transceiver.
1) Remove top cover.
2) Select desired address and/or network frequency
3) Move SW4 on SEL2 to the "CLOSED" position.
4) Wait approximately one second, then move SW4 on SEL2 back
to the "OPEN" position.
5) Programming is now complete. Replace top cover.
Note – Selected address and frequency settings will be maintained, in
the internal flash memory, even if power is removed from unit. The
above procedure needs to be performed only if changing digital
address and/or network frequency)
Seven dip switches for selecting digital address of this
SEL1 (ADDRESS)
transmitter (Maximum of 128 combinations)
Network
Address
SEL 2 (SW 1-3):
1
2
(NETWORK
3
FREQUENCY)
4
5
6
7
8
Normal Operation
SEL2 (SW4)
OPEN
SW1 SW2 SW3
OPEN OPEN OPEN
CLOSED OPEN OPEN
OPEN CLOSED OPEN
CLOSED CLOSED OPEN
OPEN OPEN CLOSED
CLOSED OPEN CLOSED
OPEN CLOSED CLOSED
CLOSED CLOSED CLOSED
Programming
CLOSED