Related Manuals for LIW BAFFIN neoSIT HL
Summary of Contents for LIW BAFFIN neoSIT HL
- Page 1 MANUAL FOR ORTHOPAEDIC SEAT STABILISING BACK AND HEAD FOR CHILDREN BAFFIN neoSIT HL sizes: S,M,L control: manual Edition 1 – 05.11.2018...
- Page 2 NOTE! DO NOT EXCEED MAXIMUM USER WEIGHT FOR BAFFIN NEOSIT HL ORTHOPAEDIC SEAT FOR CHILDREN. NOTE! DO NOT USE BAFFIN NEOSIT HL ORTHOPAEDIC SEAT FOR CHILDREN IF THERE ARE FAULTY, BROKEN OR MISSING PARTS. NOTE! READ THE MANUAL NECESSAIRLY BEFORE START-UP.
-
Page 3: Table Of Contents
Separate Footplates ..................................20 Spine interlock adjustment ................................21 Seat interchangeable system – polyamide trapezoid ........................22 Moving device ....................................... 23 General Care & Cleaning ..................................24 Service & Maintenance ..................................25 Identification plate ..................................25 Baffin neoSIT HL Edition 1... -
Page 4: Introduction
For safety and comfort whilst using the BAFFIN neoSIT HL and to avoid the risk of any damage to the equipment, it is very important to read these instructions before use and to ensure the recommendations and warnings, are read and understood, by the user and/or any others involved in operating the equipment. -
Page 5: Intended Use Of The Device
4. Indications for product use The BAFFIN neoSIT HL is intended for users whose height is within the 85 -130 cm range, with a weight limit of 60 kg. Intended Users are those with faulty postures and muscle dysfunction. Particular conditions include cerebral palsy, muscular dystrophy, paralysis of various types, tetra and paraplegia. -
Page 6: Technical Specification
5. Technical Specification Fig. 1 There are three sizes of the Baffin neoSit HL. Size details are shown in the table below: Dimension Dimension [cm] Dimension symbol Seat height 37÷68 37÷68 37÷68 Back height Back angle -5°÷25° -5°÷25° -5°÷25° Base length... -
Page 7: Adjustments And Fitting
To lock, tighten bolts 3. If the adjustment range provided by the bolts 3 is not sufficient, additional adjustment may be obtained by loosening bolts 7 and pulling or pushing the backrest. After completing the adjustment procedure, make sure the bolts 7 are tightened. Baffin neoSIT HL Edition 1... -
Page 8: Backrest Adjustment
The backrest has a unique design enabling the user to obtain its corrective or anatomical shape. The central core comprises several independent segments. The backrest can be modelled anatomically after loosening the adjustment screw 10. After the backrest optimum shape is obtained, re-tighten the adjustment screw 10. Fig. 4 Baffin neoSIT HL Edition 1... -
Page 9: Backrest Angle Adjustment
MECHANISM OF THE SEAT BASE; THERE IS A RISK OF HAND ENTRAPMENT! One of the features of Baffin neoSIT HL, orthopaedic seat stabilising the head and back for children, is the option to adjust its height. The motion mechanism is designed in such a way that while changing the seat height, the tilt angle does not change in relation to the basis. -
Page 10: Buttock Support Height Adjustment
Fig. 6 6.6 Buttock Support Height Adjustment Turn screw 9 until the required height is obtained. Fig. 7 Baffin neoSIT HL Edition 1... -
Page 11: Footrest Length Adjustment
To unlock, loosen knob 5. Move the footrest to the required length. Re-tighten knob 5 to lock into position. Fig. 8 6.8 Footrest Angle Adjustment Loosen handle knob 8, set the required angle and re-tighten knob 8. Baffin neoSIT HL Edition 1... -
Page 12: Armrest Height Adjustment
Turn knob 12 until the required height is set. The knobs are located on the left and right side. They operate independently from each other, making it possible to adjust the armrest height asymmetrically. Fig. 10 Baffin neoSIT HL Edition 1... -
Page 13: Adjusting The Seat Angle
6.10 Adjusting the seat angle BAFFIN neoSIT HL seat has the option to have the tilt adjusted in relation to the basis. Depending on the version of the device, it is operated either manually by using a lever or supported by a gas spring. -
Page 14: Adjusting The Angle By Using The Gas Spring
Baffin neoSIT’s HL Frame is equipped with four independent wheel brakes (1); brake levers are located directly on the wheels. To apply the brake, press the brake lever down (2). To release the brake, lift the brake up. The wheel brakes are operated by foot. Fig. 13 Baffin neoSIT HL Edition 1... -
Page 15: Adjusting The Push Handle
UNEXPECTED PUSH, TILTING OR LEANING ON IT. 6.12 Adjusting the push handle Baffin neoSIT HL is equipped with a push handle used for transporting the device. Depending on the version, the seating system can be equipped with a push handle -folding in one or two positions. -
Page 16: Accessories
Fig. 15 7. Accessories 7.1 Headrest Fig. 16 Baffin neoSIT HL Edition 1... -
Page 17: Headrest Assembly
Thigh Supports can be set at an angle relative to the devices length hence allowing for ten ways of setting the thighs. Adjusting the thigh supports affects the proper positioning of the knee and pelvis. Independent regulation of the thigh supports, allows for asymmetric adjustments. Baffin neoSIT HL Edition 1... -
Page 18: Fixing And Adjusting The Vest, Legs Abduction Belts And Pelvic Belts
The pelvic belts are fixed to the fastening loops located behind the armrests 27. The length of the belts is adjusted by passing the fastening belts (loosening or tightening) through the fastening buckles or loops. Fig. 19 Baffin neoSIT HL Edition 1... -
Page 19: Push Handles For The Seating System
The push handles of the seating system (1) are used when the handle bar is dismounted (3). They are mounted directly on the platform, used for raising the seating system (2), by joining elements. Fig. 20 7.6 Table 7.6.1 Adjusting the Spacing of the Table Handles Fig. 21 Baffin neoSIT HL Edition 1... - Page 20 To fit the table, loosen the locking knobs 3 and slide the table handles 1 into the sockets located under the armrests 2. After inserting the table to the proper depth, re-tighten the locking knobs 3. Baffin neoSIT HL Edition 1...
-
Page 21: Separate Footplates
1. They operate independently from each other, making it possible to adjust the platform height asymmetrically. In order to set the proper angle of the foot platform loosen the angle knob (2), set the desired angle and tighten the knob. Baffin neoSIT HL Edition 1... -
Page 22: Spine Interlock Adjustment
This adjustment enables to set the angle, tilt and position of each platform independently. 7.8 Spine interlock adjustment Fig. 26 The spine interlock is a mechanical support, that prevents spine movement in the event of being subject to a large force or impact. Baffin neoSIT HL Edition 1... -
Page 23: Seat Interchangeable System - Polyamide Trapezoid
INJURING THE PATIENT. BAFFIN neoSIT HL can be equipped with a fast seat interchangeable system. To mount the system, fit the bottom part of the system (1) on to the seat platform (3) using the joining elements (4). Top part (2) of the system is fitted directly on the seat. -
Page 24: Moving Device
(2) from the base of the interchangeable system. Rys. 29 8. Moving device Baffin neoSIT HL can be carried by holding the legs of the frame with both hands. Example of the correct way of transporting the device shown in Fig. 30. Fig. 28 Fig. -
Page 25: General Care & Cleaning
9. General Care & Cleaning Baffin neoSIT HL - orthopaedic seat for children, stabilising the back and head is a mechanical device with the supporting structure made of steel and aluminium covered with powder coating. There are sponge-foam inserts fixed on to the metal structure. -
Page 26: Service & Maintenance
The economic lifetime of the product is five years. The manufacturer provides post – warranty service. Contact details: LIW Care Technology Sp. z o.o., ul. Golfowa 7, 94-406 Łódź, Poland. reklamacje@liwcare.pl Current contact details are available on: www.liwcare.pl Warranty terms are specified in the warranty card, which is an integral part of this statement. - Page 27 Warranty terms: 1. Manufacturer of medical device - LIW Care Technology Sp. z o. o. (ul. Golfowa 7, 94-406 Łódź, Poland) ensures that the company sells an operative device, free from construction, installation, material defects, etc., and that the device will remain free from such defects during the warranty period.