Page 1
SETUP INSTRUCTIONS 2015 125 Duke EU 200 Duke EU 200 Duke AR 200 Duke ASIA 200 Duke BR 200 Duke CN 200 Duke 2016 CO 200 Duke MY Art. no. 3213323en...
Page 3
KTM accepts no liability for delivery options, deviations from illustrations and descriptions, misprints, and other errors.
MEANS OF REPRESENTATION Symbols used The meaning of specific symbols is described below. Indicates an expected reaction (e.g. of a work step or a function). Indicates an unexpected reaction (e.g. of a work step or a function). Indicates a page reference (more information is provided on the specified page). Indicates information with more details or tips.
Page 5
SETUP Unpacking and setting up the vehicle – Remove straps and box. S00786-10 – Remove the adhesive tape in the upper area of the motorcycle. S00790-10 – Roll down the film at the sides. Info To avoid damaging the motorcycle during unpacking, leave the other films on the vehicle until you have finished work on the vehicle.
Page 6
Install the battery. ( p. 7) – Refuel. ( p. 9) – Print out the current PDI form found on the KTM Dealer.net and perform the pre- delivery inspection. – Set kilometers or miles. ( p. 9) – Set the clock. (...
Page 7
WORK Removing the passenger seat – Insert the ignition key in seat lock and turn it clockwise. – Raise the rear of the seat, push it towards the rear, and remove it upwards. – Remove the ignition key from the seat lock. B00712-01 Mounting the passenger seat –...
Environmental hazard The battery contains elements that are harmful to the environment. – Do not dispose of batteries with the household waste. Dispose of a defective battery in an environmentally friendly manner. Give the battery to your authorized KTM dealer or dispose of it at a collection point for used batteries.
WORK Info Even when there is no load on the battery, it discharges steadily. The charging level and the method of charging are very important for the service life of the battery. Rapid recharging with a high charging current shortens the battery's service life. If the charging current, charging voltage, or charging time is exceeded, electrolyte escapes through the safety valves.
Page 10
WORK – Position the negative cable and mount and tighten the screw. – Position the negative terminal cover B00750-11 Finishing work – Mount the seat. ( p. 5) – Mount the passenger seat. ( p. 5) – Set the clock. ( p.
Page 11
WORK 3.10 Refueling Danger Fire hazard Fuel is highly flammable. – Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately. –...
Page 12
WORK – Press the MODE button briefly and repeatedly until ODO appears on the display. – Press the MODE button for 5 - 10 seconds. The display changes from km/h to mph or from mph to km/h. 401303-01...
Page 14
TECHNICAL DATA Loctite ® 243™ Screw, magnetic holder on side stand 5 Nm (3.7 lbf ft) – Screw, main silencer 10 Nm (7.4 lbf ft) – Screw, radiator bracket 6 Nm (4.4 lbf ft) – Screw, radiator holder 9 Nm (6.6 lbf ft) Screw, rear ABS sensor wheel (125 8 Nm (5.9 lbf ft) Loctite...
Page 15
TECHNICAL DATA Loctite ® 243™ Screw, top steering head M16x1.5 53 Nm (39.1 lbf ft) – Lambda sensor M18x1.5 19 Nm (14 lbf ft) – Swingarm bearing adjusting ring M22x1 Tighten and ensure that there is no play – Nut, steering head M30x1 Step 1 55 Nm (40.6 lbf ft)
Page 16
SUBSTANCES Super unleaded (ROZ 95/RON 95/PON 91) Standard/classification – DIN EN 228 (ROZ 95/RON 95/PON 91) Guideline – Only use unleaded super fuel that matches or is equivalent to the specified fuel grade. – Fuel with an ethanol content of up to 10 % (E10 fuel) is safe to use. Info Do not use fuel containing methanol (e.