Table of Contents
Advertisement
1330-ED / 1530-ED
1330-ED
Serial # 213301001 - Up
1530-ED
Serial # 215301001 - Up
1OP1330EN
February 2018
Global Machinery Group, Inc.
Operator's Manual
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . inside cover
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
California Proposition 65 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Alert Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Electrocution Hazard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tip-over Hazards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Fall Hazards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Collision Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Additional Safety Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Battery Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls & Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Component Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Platform Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lower Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Workplace Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operating Instructions & Function Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Prestart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Functions Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Shutdown Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Battery Charging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Frequent and Annual Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Pre-Start Inspection Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Frequent Inspection Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Annual Inspection Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Transport and Lifting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Lifting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Advertisement
Table of Contents
Related Manuals for GMG 1330-ED
Summary of Contents for GMG 1330-ED
-
Page 1: Table Of Contents
Annual Inspection Report ..........25 1330-ED / 1530-ED Troubleshooting . -
Page 2: Specifications
—Specifications— 1330-ED 1530-ED EIGHTS Working Height* 19.1' 20.7" 6.5m Platform Height 13.1' 14.7" 4.5m Stowed Height Rails Up 77" 1.95m 79.9" 2.03m Rails Folded 59" 1.5m 62.6" 1.59m Platform Floor 33.7" .86m 36.6" .93m Guardrail Height 43.3" 1.1m 43.3" 1.1m Toeboard Height 6"... - Page 3 This Operator’s Manual has been designed to provide you, the owner, user or operator, with the instructions and operating procedures essential to properly and safely operate your GMG Aerial Work Platform for positioning personnel, along with their necessary tools and materials, to overhead work locations.
-
Page 4: Safety
GMG designs aerial work platforms to safely and reliably position personnel, along with their necessary tools and materials, at overhead work locations. The owner/user/operator of the machine should not accept responsibility for the operation of the machine unless properly trained. -
Page 5: Electrocution Hazard
1330-ED / 1530-ED Safety Fall Protection Operators must comply with employer, job site and governmental rules regarding the use of personal protective equipment. If required by your employer or job site, use personal fall protection equipment (PFPE) when operating this machine. -
Page 6: Tip-Over Hazards
NEVER alter or disable any machine components. NEVER replace any part of the machine with items of different weight or specification. NEVER modify or alter the work platform without written permission from GMG. 13307 NEVER place ladders or scaffolds in the platform or against any part of the machine. -
Page 7: Fall Hazards
1330-ED / 1530-ED Safety Fall Hazards DO NOT sit, stand or climb on the platform guard rails. Maintain a firm footing on the platform floor at all times. DO NOT exit the platform when elevated Keep the platform floor clear of debris. -
Page 8: Additional Safety Hazards
1330-ED / 1530-ED Safety Additional Safety Hazards Explosion and Fire Hazards DO NOT operate the machine in hazardous locations or locations where potentially flammable or explosive gases or particles may be present. Damaged Machine Hazards Conduct a thorough prestart inspection of the machine and test all functions before each work shift to check for damage, malfunction and unauthorized modification. -
Page 9: Controls & Components
1330-ED / 1530-ED Controls & Components Controls & Components Component Locations Platform Controls Guardrails Manuals Case Deck Extension Release Platform Entry Gate Maintenance Lock Lift Cylinder Tie-Down / Tie-Down / Lift Points Lift Points Forklift Pocket Chassis Lower Control Entry Ladder... -
Page 10: Platform Controls
1330-ED / 1530-ED Controls & Components Platform Controls 13332 ALWAYS be aware of the machine’s position and of your surroundings before activating any control function. CONTROL DESCRIPTION Function Enable Switch Squeeze to enable DRIVE, STEER, and LIFT functions from the Control Handle. -
Page 11: Lower Controls
1330-ED / 1530-ED Controls & Components Lower Controls Lower Controls 13333 ALWAYS be aware of the machine’s position and of your surroundings before activating any control function. CONTROL DESCRIPTION LED Display Indicates the state of the battery charge and displays diagnostic codes when necessary. -
Page 12: Workplace Inspection
1330-ED / 1530-ED Workplace Inspection Workplace Inspection DO NOT operate this machine until you have read and understood this manual, have performed the Workplace Inspection, Pre-Start Inspection and Routine Maintenance, and have completed all the test operations detailed in the Operating Instructions section. -
Page 13: Operating Instructions & Function Tests
1330-ED / 1530-ED Operating Instructions & Function Tests Operating Instructions & Function Tests DO NOT operate this machine until you have read and understood this manual, have performed the Workplace Inspection, Prestart Inspection and Routine Maintenance, and have completed all the test operations detailed in the Operating Instructions section. - Page 14 1330-ED / 1530-ED Operating Instructions & Function Tests Test Up/Down Functions Check the area above and around the machine for obstructions and electrical power lines before operating the machine. A buzzer with different sound frequency is controlled by the central system. The descent alarm sounds at 120 beeps per minute.
- Page 15 1330-ED / 1530-ED Operating Instructions & Function Tests Test Function Enable and Up/Down Functions Check the area above and around the machine for obstructions and electrical power lines before operating the machine. 18 Press the Lift function select button. 19 DO NOT hold the Function Enable Switch on the control handle.
-
Page 16: Operating Instructions
1330-ED / 1530-ED Operating Instructions & Function Tests Test Limited Drive Speed 33 Press the Lift function select button. 34 Press the Function Enable Switch. Raise the platform approximately 4.2 ft /1.3 m from the ground. 35 Press the Drive function select button. - Page 17 1330-ED / 1530-ED Operating Instructions & Function Tests Operation from Ground Check the area above and around the machine for obstructions and electrical power lines before operating the machine. Drive and steer functions are not available from the ground controls.
- Page 18 1330-ED / 1530-ED Operating Instructions & Function Tests To Drive Control 1 Press the Drive function select button. Handle 2 Press and hold the Function Enable Switch on the control handle. • Increase speed: Slowly move the control handle off center.
- Page 19 1330-ED / 1530-ED Operating Instructions & Function Tests Driving On A Slope DO NOT drive the machine on a slope with the platform elevated. The platform must be in the fully stowed position before driving on a slope. Determine the slope and side slope ratings for the machine and determine the slope grade.
- Page 20 1330-ED / 1530-ED Operating Instructions & Function Tests Operation from Ground with Controller Use extreme caution when operating the machine with the controller from the ground Maintain safe distances between operator, machine and fixed objects. Be aware of the direction the machine will travel when using the controller.
-
Page 21: Shutdown Procedure
Charge the battery in a well-ventilated area. Use proper AC input voltage for charging as indicated on the machine. Use only GMG authorized batteries and chargers. IMPORTANT— Be sure to disconnect the charger from the outlet before attempting to operate the unit. -
Page 22: Maintenance
1330-ED / 1530-ED Maintenance Maintenance DO NOT operate this machine until you have read and understood this manual, have performed the Workplace Inspection, Pre-Start Inspection and Routine Maintenance, and have completed all the test operations detailed in the Operating Instructions section. -
Page 23: Routine Maintenance
1330-ED / 1530-ED Maintenance Routine Maintenance NEVER perform work or inspection on the machine with the platform elevated without first blocking the scissor assembly with the Maintenance Lock. See page 18 for instructions. IMPORTANT—The operator may perform only maintenance items on the Pre-Start Inspection Checklist. Frequent and Annual maintenance must be performed by qualified service technicians. -
Page 24: Lubrication
1330-ED / 1530-ED Maintenance Lubrication Operator may perform routine maintenance only. Lubrication listed as Scheduled Maintenance must be performed by a qualified service technician. FULL 13327 Lubrication ITEM SPECIFICATION FREQUENCY Hydraulic Mobile Fluid DTE 10, DTE 13M or AW32 Routine Maintenance... -
Page 25: Pre-Start Inspection Checklist
1330-ED / 1530-ED Maintenance Pre-Start Inspection Checklist The operator must conduct a Pre-Start Inspection of the machine before each work shift. DO NOT use a damaged or malfunctioning machine. Initial Description Be sure that the operator's manual is complete, legible and in the storage container located in the platform. -
Page 26: Frequent Inspection Checklist
1330-ED / 1530-ED Maintenance Frequent Inspection Checklist This checklist must be used at 3-month intervals or every 150 hours of machine use, whichever occurs first. Failure to do so could result in death or serious injury. Frequent Maintenance Inspections should be conducted by qualified service technicians only. Photocopy this page for reuse. Keep inspections records up to date. -
Page 27: Annual Inspection Report
1330-ED / 1530-ED Maintenance Annual Inspection Report Annual Inspection Report Date Serial Number Global Machinery Group, Inc. Model Number 3428 Bullock Lane, San Luis Obispo, CA 93401 USA Date Of Last Inspection 800-301-0499 • 805-303-2066 • Fax: 805-293-6211 Date Placed In Service... -
Page 28: Troubleshooting
• Obvious fluid leak or damaged component? • Wires disconnected, broken, or loose? • Diagnostic panel on? • Fault Code present at platform control box? Refer to service manual or contact GMG Technical Support. Page 26 1OP1330 – February 2018... -
Page 29: Transport And Lifting Instructions
Truck drivers are responsible for loading and securing machines, and should be properly trained and authorized to operate GMG machinery. Drivers are also responsible for selecting the correct and appropriate trailer according to government regulations and company policy. Drivers must ensure that the vehicle and chains are strong enough to hold the weight of the machine (see the serial number plate for machine weight). - Page 30 1330-ED / 1530-ED Transport and Lifting Instructions Driving or Winching onto or off of a Transport Vehicle Always attach the machine to a winch when loading or unloading from a truck or trailer by driving. Read and understand all safety, control, and operating information found on the machine and in this manual before operating the machine.
-
Page 31: Lifting Instructions
1330-ED / 1530-ED Transport and Lifting Instructions Lifting Instructions Only qualified riggers shall rig and lift the machine. Ensure that the crane, loading surfaces, spreader bars, cables, chains and straps are of sufficient capacity to withstand the machine weight. See the serial plate for the machine weight. - Page 32 Global Machinery Group, Inc. Global Machinery Group, Inc. 3428 Bullock Lane San Luis Obispo, CA 93401 USA Phone: +1.805.303.2066 Toll Free (USA/Canada): 800.303.0499 www.goGMG.com...
Need help?
Do you have a question about the 1330-ED and is the answer not in the manual?
Questions and answers