Brush Bandit HB19 Operating & Parts Manual
  1. Manuals
  2. Brands
  3. Brush Bandit Manuals
  4. Grinder
  5. HB19
  6. Operating & parts manual

Brush Bandit HB19 Operating & Parts Manual

Stump grinder
Hide thumbs
Table of Contents

Advertisement

Quick Links

ATTENTION:
Depending on what replacement
parts you are ordering, we will
need the following information:
GRINDER COMPONENTS
Serial Number
Model Number of Grinder
ENGINE COMPONENTS
Brand
Engine Serial Number
Engine Spec. Number
CLUTCH COMPONENTS
Brand
Serial Number
Assembly of Clutch
BUILT WITH QUALITY
AND DESIGN FIRST
STUMP GRINDER
MODELS HB19/HB19SP/HB20SP
OPERATING & PARTS MANUAL
Model No: _________________
Serial No: _________________
DEALER:
Name: ____________________
Address: __________________
City/State: _________________
Phone No: _________________
Delivery Date: ______________
Engine Make: ______________
Serial No: _________________
Clutch Make: _______________
Model: _________ S/N _______
Copyright 8/07
BANDIT INDUSTRIES, INC.
REMUS, MICHIGAN, USA 49340
PHONE: (800) 952-0178 IN USA
PHONE: (989) 561-2270 OR 561-2272
FAX: (989) 561-2273 ~ SALES DEPT.
FAX: (989) 561-2962 ~ PARTS/SERVICE
E-MAIL: www.banditchippers.com
MANUFACTURED BY
6750 Millbrook Road

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HB19 and is the answer not in the manual?

Questions and answers

Related Manuals for Brush Bandit HB19

Summary of Contents for Brush Bandit HB19

  • Page 1 BUILT WITH QUALITY AND DESIGN FIRST STUMP GRINDER ATTENTION: Depending on what replacement MODELS HB19/HB19SP/HB20SP parts you are ordering, we will need the following information: OPERATING & PARTS MANUAL GRINDER COMPONENTS Serial Number Model Number of Grinder Model No: _________________...
  • Page 2 CALIFORNIA PROPOSITION 65 WARNING ADVERTENCIA Breathing diesel engine Respirar gases de escape de exhaust exposes you to motores diesel expone chemicals known to the quÍmicos conocidos por el estado State of California to cause de California como causales de cancer and birth defects or cáncer y defectos congénitos u other reproductive harm.

  • Page 3: Table Of Contents

    MODELS HB19/HB19SP/HB20SP TABLE OF CONTENTS TABLE OF CONTENTS PAGES INTRODUCTION & WARRANTY ............2 SERIAL NUMBER LOCATIONS ............SAFETY PROCEDURES ..............7 EQUIPMENT SPECIFICATIONS ............10 DECALS .................... 11 CONTROLS ..................19 MACHINE OPERATION ..............23 MAINTENANCE ................. 26 HYDRAULIC SECTION ............. 37 CUTTER WHEEL SECTION ............

  • Page 4: Introduction & Warranty

    INTRODUCTION & WARRANTY INTRODUCTION The purpose of this manual is to provide the user with specifications and procedures for the operation, maintenance and repair of this BANDIT product. As with any piece of equipment, safety should always be a constant thought while the machine is being operated, serviced or stored. In order to highlight this consideration, the material which addresses safety is proceeded by the following signal words: Degree of Potential Signal Word...

  • Page 6: Serial Number Locations

    MODELS HB19/HB19SP/HB20SP SERIAL NUMBER LOCATIONS TYPICAL GRINDER SERIAL NUMBER AND/OR WORK ORDER NUMBER LOCATIONS 1. Work Order Number NOTE: The engine information is located on the . Serial Number For HB9 engine block. The clutch information is & HB9SP located on the clutch plate.

  • Page 7: Safety Procedures

    MODELS HB19/HB19SP/HB20SP SAFETY PROCEDURES SAFETY PROCEDURES DANGER The words Danger, Warning, Caution, and DANGER Notice are used on the safety decals and throughout this manual, to make you aware of the safety Before starting the machine, take a minute to check a procedures.
  • Page 8 MODELS HB19/HB19SP/HB20SP SAFETY PROCEDURES SAFETY PROCEDURES DANGER DANGER Do not go near or in-line with the debris field of NEVER sit, stand, lay, climb or ride anywhere the stump grinder while in operation. While grinding on this machine while it is running, operating, or in stumps, the chips and portions of the stump fly from transit.
  • Page 9 MODELS HB19/HB19SP/HB20SP SAFETY PROCEDURES SAFETY PROCEDURES DANGER DANGER Never grind any materials that might contain wires, Do Not start to grind a stump unless you are completely sure there are not any power lines, water stones, nails, or other metal objects which may lines, sewer lines, phone lines, etc.

  • Page 10: Equipment Specifications

    MODELS HB19/HB19SP/HB20SP EQUIPMENT SPECIFICATIONS EQUIPMENT SPECIFICATIONS Approximate Dimensions & Weights (Dimensions & weights will vary depending on optional equipment) Approx. Model HB19: 400 to 500 Lbs. (181 to 227 kg) Weight: Model HB19SP: 550 to 650 Lbs. (249 to 295 kg) Model HB20SP: 650 to 750 Lbs.

  • Page 11: Decals

    MODELS HB19/HB19SP/HB20SP DECALS DECALS WARNING WEAR EYE & PERSONAL PROTECTION EQUIPMENT Wear all personal protection equipment and follow all safety standards per ANSI and OSHA instructions. Bandit Copyright 8/07 PAGE ...
  • Page 12 MODELS HB19/HB19SP/HB20SP DECALS DECAL LOCATIONS - MODEL HB19 Decal locations may vary, these are general locations. 14,15,16,17,18,19 9,12,21,22 2,10,11 3,23,24 Bandit Copyright 8/07 PAGE ...
  • Page 13 MODELS HB19/HB19SP/HB20SP DECALS DECAL LOCATIONS - MODEL HB19 Modifications and/or additions of decals to this list will happen. Consult grinder dealer or manufacturer for most current decal package. LOCATION NUMBER DESCRIPTION SPD-0 Moving Parts Keep Hands... SPD-0 Flying Objects Stand Clear...
  • Page 14 MODELS HB19/HB19SP/HB20SP DECALS DECAL LOCATIONS - MODEL HB19SP Decal locations may vary, these are general locations. 16,17,18,19,20 9,13,22,23 3,4,5,24,25 2,10,11,21 Bandit Copyright 8/07 PAGE ...
  • Page 15 MODELS HB19/HB19SP/HB20SP DECALS DECAL LOCATIONS - MODEL HB19SP Modifications and/or additions of decals to this list will happen. Consult grinder dealer or manufacturer for most current decal package. LOCATION NUMBER DESCRIPTION SPD-0 Moving Parts Keep Hands... SPD-0 Flying Objects Stand Clear...
  • Page 16 MODELS HB19/HB19SP/HB20SP DECALS DECAL LOCATIONS - MODEL HB20SP Decal locations may vary, these are general locations. 17,18,19,20,22 4,5,6 3,32 1,13,14 9,21 29,30 12,24 7,25 26,27 2,8,9 Bandit Copyright 8/07 PAGE 6...
  • Page 17 MODELS HB19/HB19SP/HB20SP DECALS DECAL LOCATIONS - MODEL HB20SP Modifications and/or additions of decals to this list will happen. Consult grinder dealer or manufacturer for most current decal package. LOCATION NUMBER DESCRIPTION SPD-0 Moving Parts Keep Hands... SPD-0 Flying Objects Stand Clear...
  • Page 18 MODELS HB19/HB19SP/HB20SP DECALS DECALS Decals located on your Bandit equipment contain useful information to assist you in operating your equipment safely. Some of the decals on your machine and their location are shown in this section. It is very important that all decals remain in place and in good condition on your machine. Please follow the care and instructions given below: 1) You should use soap and water to keep your decals clean.
  • Page 19 CONTROLS CONTROL OPERATING PROCEDURES Parking Brake - (HB19 & HB19SP): The parking brake will keep the machine from moving forward or backwards, but still allow the machine to pivot. Push the brake lever forward (away from the operator) to release the brake. Pull the brake lever back (towards the operator) to activate the brake.

  • Page 20: Controls

    MODELS HB19/HB19SP/HB20SP CONTROLS CONTROLS Models HB19 & HB19SP Basic Location of Controls and Adjustments LOCATION SHOWN NOT SHOWN Parking Brake Transmission (HB19SP Only) Hour Meter Bail Handle Drive Train Control (HB9SP Only) Engine Controls Wheel Nuts / Wheel Studs Handle Adjustment...
  • Page 21 MODELS HB19/HB19SP/HB20SP CONTROLS CONTROLS Model HB20SP Basic Location of Controls and Adjustments LOCATION SHOWN NOT SHOWN Hour Meter Pump Belt Engine Controls Bail Handle Drive Train Control Engine Controls Swivel Frame Lock Handle Adjustment Lug Nuts / Drive Wheel Motor Nuts...
  • Page 22 MODELS HB19/HB19SP/HB20SP CONTROLS CONSULT THE ENGINE MANUFACTURER’S MANUAL FOR SPECIFIC CONTROLS, OPERATION, & MAINTENANCE FOR TYPICAL ENGINES Ignition Switch: Turn the ignition switch key clockwise one stop (on position) to turn the electrical system on. The key should remain in the on position while the engine is running.

  • Page 23: Machine Operation

    MODELS HB19/HB19SP/HB20SP MACHINE OPERATION MACHINE OPERATION • Check all fluids before starting the machine. • Make sure to go through the daily start-up and maintenance procedures before operating the machine. • Clutch must be disengaged before starting if equipped. • Hold bail handle down to start engine. Engine will shut down when the bail handle is released.
  • Page 24 MODELS HB19/HB19SP/HB20SP MACHINE OPERATION MOVING A MACHINE WITHOUT POWER NOTICE FOR MODEL HB19SP: If the hydraulic valve bypass is pushed in (see Figure 1), the machine is ready to be moved under manual power. Pull the hydraulic valve bypass out to move the machine with power.
  • Page 25 MODELS HB19/HB19SP/HB20SP MACHINE OPERATION CUTTING AREA DANGER For optimum performance, the stump should be cut with the portion of the cutter wheel shown below. NEVER UNDERCUT THE STUMP. Undercutting the stump may cause severe kickback, vibration and component damage. NEVER CUT THE STUMP FROM THE TOP. The cutter wheel will throw debris up and toward the operator, instead of down and under the machine.
  • Page 26 MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION MAINTENANCE SECTION The Bandit is a very simple machine to maintain. If you will follow a regular scheduled preventative maintenance program you should have years of trouble free operation. DANGER Before attempting any type of maintenance disengage clutch, turn off engine, wait for the cutterwheel to come to a complete stop, install the cutterwheel lock pin, place cutterwheel on the ground, disconnect battery, and make sure the ignition key is in your possession.
  • Page 27 MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION DAILY START UP & MAINTENANCE cont. 7) Check cutter teeth bolts: 15) Check the fuel level: All cutter teeth bolts must be factory approved. Check the fuel level, running out and repriming is time Bolts must be replaced after a maximum of 4-5 consuming.
  • Page 28 1) Grease upper frame pivot bushings (Model 4) Check wheel nuts or studs: HB20SP Only): For Model HB19, keep wheel nuts tight, insure the Grease upper frame pivot bushings with  to  shots of cotter pin is installed, retorque, replace if needed.
  • Page 29 MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION 3 MONTH MAINTENANCE 1) Hydraulic oil filter (Model HB20SP Only): Must be replaced after FIRST 10 HOURS OF OPERATION, USE A 10 MICRON FILTER. After first change replace oil filter every 3 months or 400 hours.
  • Page 30 MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION DAILY START UP & MAINTENANCE CHECK LIST Each day before starting your machine these checks must be made: O.K. Repaired Check the safety decals and engine gauges, replace if damaged. Check, maintain, and service all safety equipment for proper operation.
  • Page 31 Grease or anti-seize handle bar pivot pins. Grease or anti-seize end of frame swivel lock (Model HB20SP Only). Check and grease wheel bearings (Model HB19 Only). Lubricate inner control cables and cable ends. Check and fill tires to rated pressures.

  • Page 32: Maintenance

    MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION MAINTENANCE SECTION BOLT TORQUE CHART (THESE TORQUES ARE BASED ON DRY, CLEAN THREADS) DESCRIPTION BOLT SIZE TORQUE (FT.-LBS.) TORQUE (Nm) Grinder Bearing Bolts /” -  NC Grinder Bearing Set Screw /6” -  NF Cutter Wheel Shaft Bolts 7/6”...
  • Page 33 MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION GREASE CHART - MODEL HB19 CHECK DESCRIPTION DAY MONTH YEAR PROCEDURE Cutter Wheel Bearings Purge bearing daily - wipe off excess Handle Bar Pivot Pins Grease or anti-seize - wipe off excess Wheel Bearings Grease - wipe off excess...
  • Page 34 MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION GREASE CHART - MODEL HB19SP CHECK DESCRIPTION DAY MONTH YEAR PROCEDURE Cutter Wheel Bearings Purge bearing daily - wipe off excess Handle Bar Pivot Pins Grease or anti-seize - wipe off excess Control Cables Lubricate the inner cables and ends...
  • Page 35 MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION GREASE CHART - MODEL HB20SP CHECK DESCRIPTION DAY MONTH YEAR PROCEDURE Cutter Wheel Bearings Purge bearing daily - wipe off excess Upper Frame Pivot Bushing 1 to 2 shots of grease - wipe off excess Handle Bar Pivot Pins...
  • Page 36 MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Engine will not start. . Loose ground cable. . Clean and tighten. (See Engine MFG. . Loose hot cable. . Clean and tighten. manual for further . Dead battery. . Recharge or replace.

  • Page 37: Hydraulic Section

    MODELS HB19/HB19SP/HB20SP HYDRAULIC SECTION HYDRAULIC SECTION WARNING DO NOT GO NEAR HYDRAULIC LEAKS! High pressure oil easily punctures skin causing serious injury, gangrene, or death. If injured, seek emergency medical help. Immediate surgery is required to remove oil. DO NOT use fingers or skin to check for leaks. Lower load or relieve hydraulic pressure before loosening fittings.
  • Page 38 MODELS HB19/HB19SP/HB20SP HYDRAULIC SECTION HYDRAULIC SECTION Alternate hydraulic oils are available, but they do not equal the performance or longevity of the “Hydrex XV” oil. Consult the following information supplied by the oil distributor. C E L C IU S...
  • Page 39 MODELS HB19/HB19SP/HB20SP HYDRAULIC SECTION HYDRAULIC SECTION THE BANDIT HYDRAULIC SYSTEM The Bandit is equipped with a very efficient, simple • Keep hydraulic oil clean. Dirty oil will cause excessive hydraulic system. Each component is capable of wear and loss of hydraulic power.
  • Page 40 MODELS HB19/HB19SP/HB20SP HYDRAULIC SECTION TROUBLE SHOOTING BEFORE ATTEMPTING ANY TYPE OF MAINTENANCE DISENGAGE CLUTCH, TURN OFF ENGINE, WAIT FOR THE CUTTER WHEEL TO COME TO A COMPLETE STOP, INSTALL THE CUTTER WHEEL LOCK PIN, DISCONNECT BATTERY, AND MAKE SURE THE IGNITION KEY IS IN YOUR POSSESSION.
  • Page 41 MODELS HB19/HB19SP/HB20SP HYDRAULIC SECTION MODEL HB20SP HYDRAULIC SCHEMATIC SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURER. LEFT DRIVE RIGHT DRIVE WHEEL WHEEL MOTOR MOTOR COUNTER BALANCE TIMING CYLINDER VARIABLE PUMP SUCTION RETURN SCREEN FILTER HYDRAULIC TANK Bandit...

  • Page 42: Cutter Wheel Section

    There are eight (8) teeth to a complete set on the A locking pin is provided to hold the cutter wheel model HB19, HB19SP, or HB20SP built during and in position during tooth removal and reinstallation. after 8/07. Four (4) straight teeth, two (2) left 45° teeth, Locking pin will only lock on outer teeth.
  • Page 43 There are twelve () teeth to a complete set on the A locking pin is provided to hold the cutter wheel model HB19, HB19SP, or HB20SP built before 8/07. in position during tooth removal and reinstallation. Two (2) straight teeth, five (5) left 45° teeth, and five Locking pin will only lock on outer teeth.
  • Page 44 MODELS HB19/HB19SP/HB20SP BELT SECTION BELT TENSION GENERAL RULES FOR TENSIONING 1. Check tensioning during the first 2-48 hours of run-in operation. . Over tensioning or under tensioning shortens belt and bearing life. . Keep belts free from foreign materials that may cause the belt to slip.
  • Page 45 MODELS HB19/HB19SP/HB20SP MAINTENANCE SECTION BELT TENSION Engine Puller Bolt For Models HB9 & HB9SP Engine Puller Bolt For Model HB0SP Worn or misaligned belts and sheaves in the power train Main Drive belts maximum of 5/32” deflection causes belt slippage, thus power loss. Keep the power with 0 lbs.

  • Page 46: Lubrication & Coolant

    2) Engine Coolant: Refer to engine manufacturers manual specifications. 3) Wheel Bearings (Model HB19 Only): Check and grease wheel bearings with an EP-2 Lithium grease. Wipe off excess grease. Excessive grease will attract dirt. 4) Hydrostatic Transmission (Model HB19SP Only): Change hydrostatic transmission oil yearly or every 00 hours.
  • Page 47 MODELS HB19/HB19SP/HB20SP ELECTRICAL SECTION KOHLER ENGINE SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. Bandit Copyright 8/07 PAGE 7...
  • Page 48 MODELS HB19/HB19SP/HB20SP ELECTRICAL SECTION HONDA ENGINE SPECIFIC SCHEMATIC FUNCTION MAY VARY DEPENDING ON OPTIONS OR COMPONENT MANUFACTURE. Bandit Copyright 8/07 PAGE 8...

  • Page 49: Replacement Parts Section

    MODELS HB19/HB19SP/HB20SP REPLACEMENT PARTS REPLACEMENT PARTS SECTION Depending on what replacement parts you are ordering the following information will be needed: GRINDER COMPONENTS ENGINE COMPONENTS CLUTCH COMPONENTS Serial Number Brand Brand Model Number of Grinder Engine Serial Number Serial Number Engine Spec.
  • Page 50 MODELS HB19/HB19SP/HB20SP CUTTER WHEEL COMPONENTS Bandit NOTE: Parts may not be exactly as shown. Copyright 8/07 PAGE 0...
  • Page 51 MODELS HB19/HB19SP/HB20SP CUTTER WHEEL COMPONENTS LOCATION PART NUMBER DESCRIPTION 900-4906-73 1/2”-13NC x 1 3/4” Hex Head Bolt 900-909-8 /” Mill Carb Washer 900-9-08 Cutter Wheel Bearing 900-4901-76 1/2”-13NC Lock Nut 900-4908-87 7/16”-20NF Lock Nut 00-0006 Cutter Wheel Shaft 7 a.
  • Page 52 MODELS HB19/HB19SP/HB20SP FRAME COMPONENTS MODEL HB19 MODEL HB9 LOCATION PART NUMBER DESCRIPTION 900-4907-44 Cutter Head Lock Pin 900-9-7 Cotter Key 900-909-08 ”-8NC Castle Nut 4 a. 901-100014 4.80” x 8” Turf Tire and Solid White Rim With Brake Drum Hub Assembly 900-5907-58 4.80”...
  • Page 53 MODELS HB19/HB19SP/HB20SP FRAME COMPONENTS MODEL HB19SP PRE ??/?? MODEL HB9SP LOCATION PART NUMBER DESCRIPTION 900-4907-44 Cutter Head Lock Pin 900-9-68 /”-0NF Wheel Stud 3 a. 900-5906-01 6-12 Traction Tire and White Spoke, 4 Bolt Rim Assembly 900-907-7 6- Traction Tire Only 900-5907-59 12”...
  • Page 54 MODELS HB19/HB19SP/HB20SP FRAME COMPONENTS MODEL HB20SP Bandit NOTE: Parts may not be exactly as shown. Copyright 8/07 PAGE ...
  • Page 55 MODELS HB19/HB19SP/HB20SP FRAME COMPONENTS MODEL HB20SP MODEL HB0SP LOCATION PART NUMBER DESCRIPTION 900-4907-44 Cutter Head Lock Pin 900-4906-11 3/8”-16NC x 1” Carriage Bolt 900-4906-62 3/8” Lock Washer 900-4906-60 3/8”-16NC Lock Nut 200-200038 Swivel Frame Lock Assembly 900-9- Ball Knob 900-90-66...
  • Page 56 MODELS HB19/HB19SP/HB20SP HANDLE BAR COMPONENTS Bandit NOTE: Parts may not be exactly as shown. Copyright 8/07 PAGE 6...
  • Page 57 Handle Bar Assembly 3 a. 900-4904-90 Spring Lock For Handle Bar (Not Shown) 900-7900-96 Rubber Cap For Spring Lock 4 a. 900-4909-47 Brake Cable - Model HB19 900-4912-63 Brake Cable - Model HB19SP 900-9-6 Cable Clamp - Model HB9SP 900-9-6 Spacer 900-9-66...
  • Page 58 MODELS HB19/HB19SP/HB20SP ENGINE & BELT COMPONENTS MODELS HB19/HB19SP DIRECT DRIVE MOTOR Bandit NOTE: Parts may not be exactly as shown. Copyright 8/07 PAGE 8...
  • Page 59 00-0000 Engine Tensioner Assembly - Model HB9SP 900-4908-80 3/8”-16NC x 4” Engine Puller Bolt 12 a. 200-200004 Beltshield Back Assembly - Model HB19 201-200000 Beltshield Back Assembly - Model HB19SP 00-0006 Engine Shaft Spacer - Model HB9SP 900-9- Hydrostatic Engine Sheave - Model HB9SP...
  • Page 60 MODELS HB19/HB19SP/HB20SP ENGINE & BELT COMPONENTS MODEL HB20SP Bandit NOTE: Parts may not be exactly as shown. Copyright 8/07 PAGE 60...
  • Page 61 MODELS HB19/HB19SP/HB20SP ENGINE & BELT COMPONENTS MODEL HB20SP LOCATION PART NUMBER DESCRIPTION 900-69-  CCA Battery 900-7901-35 Plastic Battery Liner Box - Black 900-97- Wire Clip 900-9-96 /” NPT Cap - Oil Drain Hose 00-00000 Engine Oil Drain Hose 900-9-6...

  • Page 62: Chip Guard Components

    200-300026 Skirt Mount Bracket 200-300016 Rear Side Rubber Skirt (Pre 8/07) 5 a. 201-300027 Outside Rear Skirt Mount - Model HB19 200-300015 Outside Rear Skirt Mount - Model HB19SP 6 a. 201-300023 Outside Rear Rubber Skirt - Model HB19 200-300018...
  • Page 63 MODELS HB19/HB19SP/HB20SP CHIP GUARD COMPONENTS MODEL HB20SP LOCATION PART NUMBER DESCRIPTION 00-00-9 Drive Frame Chip Guard 00-00-9 Main Chip Guard NOTE: Nuts, bolts, washers, and all other components can be ordered by physical description. Bandit NOTE: Parts may not be exactly as shown.

  • Page 64: Hydraulic Components

    MODELS HB19/HB19SP/HB20SP HYDRAULIC COMPONENTS MODEL HB20SP Drive Wheel Motor: 900-3928-25 Castle Nut Only: 900-4913-97 Woodruff Key Only: 900-4914-01 Hydraulic Pump: 900-3938-24 Rodless Timing Cylinder: 900-3938-83 (Start /07) Timing Cylinder (Pre 2/07): N/A Bandit NOTE: Parts may not be exactly as shown.
  • Page 65 MODELS HB19/HB19SP/HB20SP HYDRAULIC COMPONENTS MODEL HB20SP Counter Balance: 900-3918-65 Relief Only: 900-3929-09 Return Filter Assembly: 900-3938-23 (Includes Filter Element) Filter Element Only: 900-3938-96 Suction Screen: 900-3900-07 Bandit NOTE: Parts may not be exactly as shown. Copyright 8/07 PAGE 6...
  • Page 66 MODELS HB19/HB19SP/HB20SP HYDRAULIC COMPONENTS MODEL HB20SP COUNTER BALANCE DRIVE DRIVE WHEEL WHEEL MOTOR MOTOR HYDRAULIC PUMP HYDRAULIC TANK TIMING CYLINDER LOCATION PART NUMBER DESCRIPTION  a. 900-98- Return Filter Assembly (Includes Filter Element) 900-98-96 Filter Element Only 200-200031 1 1/2 Gallon Steel Hydraulic Tank...

  • Page 67: Service Record

    MODELS HB19/HB19SP/HB20SP SERVICE RECORD SERVICE RECORD DATE DESCRIPTION AMOUNT Bandit Copyright 8/07 PAGE 67...
  • Page 68 MODEL HB19SP ONLY...
  • Page 87 www.ogura-clutch.com...
  • Page 88 www.ogura-clutch.com...
  • Page 89 www.ogura-clutch.com...
  • Page 90 www.ogura-clutch.com...
  • Page 91 www.ogura-clutch.com...
  • Page 92 www.ogura-clutch.com...

This manual is also suitable for:

Hb19spHb20sp

Table of Contents