Tap Equipment And Assembly - Marvel MO24BN Installation, Operation And Maintenance Instructions

This beer dispensing unit will support one half (
or one quarter ( ⁄ ) barrel. The double draft tower units can
1
4
support two sixth ( ⁄ ) barrels of beer. See chart below for
1
6
quantity of beer in each barrel size.
1/6 barrel
23 ⁄ "
5
16
Height
(59.2 cm)
9 ⁄ "
1
4
Diameter
(23.5 cm)
Gallons 5.16
#12 ounce
60
Glasses
Keg Size
5 gallon Corny
1/6 barrel
1/4 Barrel
1/2 Barrel
Table B
CAUTION
!
Information that follows on pages 11 through 18 does not
apply to models MO24BN, as these models do not include
any tap and tower equipment. Refer to your beer equip-
ment manufacturer information regarding to the installation
of this equipment.

Tap Equipment and Assembly

Your dispensing kit includes the following parts:
Polished stainless steel tower with clear beer line (single
or double dispense)
Tower Gasket
Phillips oval head screws
Knob for Tower (Faucet Handle)
Keg coupler(s)
CO regulator with red gas line(s) attached
2
Empty 5 pound CO tank
2
Plastic clamp(s) large and small
Faucet wrench
USING YOUR BEER DISPENSER
⁄ ) barrel
1
2
Barrel Sizes
1/4 Barrel 1/2 Barrel
14 ⁄ " 23 ⁄
13 5
16
(37.6 cm) (59.2 cm)
17" 17" to 17
(43.2 to 43 cm)
(43.2 cm)
7.75 15.5
82 163
Table A
#of kegs per
5 pound CO Tank
2
15 to 22
14 to 21
10 to 14
5 to 7
Tools required for installation:
Flat bladed screwdriver
Phillips screwdriver
Pliers
Adjustable wrench or a 1
⁄ " open end wrench
1
2
"
16
⁄ "
1
4
CO can be dangerous. If it becomes difficult to
2
breathe and/or your head starts to ache, a high
concentration of carbon dioxide may be present.
Leave the area immediately.
• The CO
regulator. Never connect the tank to the keg.
• The CO
upright position. Secure it with the chain pro-
vided.
• Never drop or throw the CO
• Keep the CO
• Ventilate the area after a CO
1. Remove shelving and packaged components from the
interior of the refrigerator before beginning the assem-
bly process.
2. Take your empty 5 pound CO
supply dealer to be filled. You can usually find them in
your "yellow pages" under "Welding Supply" or "Fire
Protection". One 5 pound tank can process many kegs
(see Table B).
3. Tower Mounting: DO NOT REMOVE INSULATION
INSIDE OF STAINLESS STEEL TOWER. INSULATION
KEEPS BEER IN CLEAR LINE COLD AND FRESH.
Mounting Tower to Refrigerator Top: Remove the
foam plug from the porthole and DO NOT reseal.
Clearance in porthole is necessary for cold air to flow
into the tower and keep the beer line cold.
Mounting Tower to Counter Top: Remove the foam
plug from the porthole and use to "bridge" the gap
between the top of the cabinet and the underside of the
counter. Leave adequate clearance for cold air to flow
into the tower and keep the beer line cold.
11
⁄ " open end wrench
1
8
WARNING
!
tank must always be connected to the
2
tank must be securely mounted in the
2
tank.
2
tank away from heat.
2
leak.
2
tank to your local gas
2