Summary of Contents for IAC INDUSTRIES SMS S1 SMART MOBILE STATION
Page 1
SMS S1 SMART MOBILE STATION UE ASSEMBLY INSTRUCTIONS IAC INDUSTRIES 895 BEACON STREET BREA, CA 92821-2926 Phone (713) 990-8997 Fax (714) 990-0557 REVISON 112012 www.iacindustries.com...
Page 2
ATTENTION IAC Industries takes great care in the packing of it's products, however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order.
Page 4
SMS P1 Parts List ( See Page 3 ) Item Part# Description 21700101 SMS Upright Sub-assembly UE 60L 10422101 Worksurface 26D x 28L STD T-Mold 29601201 SMS Base Sub-Assembly Basic 29600411 SMS Worksurface Support RT 29600412 SMS Worksurface Support LT 44501008 LAN Wire Management Channel 27.88L Hardware Kit HWR501...
Page 5
SMS BASE / UPRIGHT ASSEMBLY SMS UPRIGHT SUB-ASSEMBLY ELECTRICAL OUTLETS SMS UPRIGHT POWERCORD LAMINATE PANELS REMOVED IN THE FRONT AND REAR SMS BASE POWERCORD SMS MAIN POWERCORD Install the casters to the SMS base. Thread the 1/2-13 hex nuts all the way onto the stems of the casters. Use a split lock washer (Item R) on each caster stem.
Page 6
SMS WORKSURFACE INSTALLATION Install 5/16-18 x .75 square head bolts (item H), 5/16 flat washer (item D), and 5/16-18 hex head keps nuts (item J) to the top support brackets items (4 and 5) as shown at left . Do not tighten this hardware. Make small pencil marks on the uprights desired working height.
Page 7
SMS CORD WRAP BARCKET AND CORD MANAGEMENT CHANNEL Install 5/16-18 x .75 square head bolts (item H), 5/16 flat washer (item D), and 5/16-18 hex head keps nuts (item J) to the cord wrap bracket (item L). Do not tighten this hardware.
ESD GROUNDING: ESD refers to the OPTIONAL static dissipative laminate used on the bench. The laminate has a conductive under layer that comes in contact with the factory installed grounding bolts in the worksurface. The ESD grounding kit, including the 10 ft. grounding wire must be attached and the bench must be properly grounded to your facility earth ground.
Page 9
SMS S2 SMART MOBILE STATION UE ASSEMBLY INSTRUCTIONS IAC INDUSTRIES 895 BEACON STREET BREA, CA 92821-2926 Phone (713) 990-8997 Fax (714) 990-0557 REVISON 112012 www.iacindustries.com...
Page 10
ATTENTION IAC Industries takes great care in the packing of it's products, however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order.
Page 12
SMS S2 Parts List ( See Page 3 ) Item Part# Description 21700101 SMS Upright Sub-assembly UE 60L 10422101 Worksurface 26D x 28L STD T-Mold 29601201 SMS Base Sub-Assembly Basic 29600411 SMS Worksurface Support RT 29600412 SMS Worksurface Support LT 44501008 LAN Wire Management Channel 27.88L 16428802...
Page 13
SMS BASE / UPRIGHT ASSEMBLY SMS UPRIGHT SUB-ASSEMBLY ELECTRICAL OUTLETS SMS UPRIGHT POWERCORD LAMINATE PANELS REMOVED IN THE FRONT AND REAR SMS BASE POWERCORD SMS MAIN POWERCORD Install the casters to the SMS base. Thread the 1/2-13 hex nuts all the way onto the stems of the casters. Use a 1/2" split lock washer (Item R) on each stem.
Page 14
SMS WORKSURFACE INSTALLATION Install 5/16-18 x .75 square head bolts (item H), 5/16 flat washer (item D), and 5/16-18 hex head keps nuts (item J) to the top support brackets items (4 and 5) as shown at left . Do not tighten this hardware. Make small pencil marks on the uprights desired working height.
Page 15
SMS CORD WRAP BARCKET AND CORD MANAGEMENT CHANNEL Install 5/16-18 x .75 square head bolts (item H), 5/16 flat washer (item D), and 5/16-18 hex head keps nuts (item J) to the cord wrap bracket (item L). Do not tighten this hardware.
SMS LOWER SHELF Installation nstall 5/16-18 x .75 square head bolts (item D), 5/16 flat washer (item A), and 5/16-18 hex head keps nuts (item E) to the top support brackets for the shelf (items 2 and 3) as shown . Do not tighten this hardware.
Page 18
ESD GROUNDING: ESD refers to the OPTIONAL static dissipative laminate used on the bench. The laminate has a conductive under layer that comes in contact with the factory installed grounding bolts in the worksurface. The ESD grounding kit, including the 10 ft. grounding wire must be attached and the bench must be properly grounded to your facility earth ground.
Page 19
SMS S3 SMART MOBILE STATION UE ASSEMBLY INSTRUCTIONS IAC INDUSTRIES 895 BEACON STREET BREA, CA 92821-2926 Phone (713) 990-8997 Fax (714) 990-0557 REVISON 112012 www.iacindustries.com...
Page 20
ATTENTION IAC Industries takes great care in the packing of it's products, however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order.
Page 22
SMS S3 Parts List ( See Page 3 ) Item Part# Description 21700101 SMS Upright Sub-assembly UE 60L 10422101 Worksurface 26D x 28L STD T-Mold 29601201 SMS Base Sub-Assembly Basic 29600411 SMS Worksurface Support RT 29600412 SMS Worksurface Support LT 44501008 LAN Wire Management Channel 27.88L 16428802...
Page 23
SMS BASE / UPRIGHT ASSEMBLY SMS UPRIGHT SUB-ASSEMBLY ELECTRICAL OUTLETS SMS UPRIGHT POWERCORD LAMINATE PANELS REMOVED IN THE FRONT AND REAR SMS BASE POWERCORD SMS MAIN POWERCORD Install the casters to the SMS base. Thread the 1/2-13 hex nuts all the way onto the stems of the casters. Use a 1/2 split lock washer (Item Q) on each stem.
Page 24
SMS WORKSURFACE INSTALLATION Install 5/16-18 x .75 square head bolts (item H), 5/16 flat washer (item D), and 5/16-18 hex head keps nuts (item J) to the top support brackets items (4 and 5) as shown at left . Do not tighten this hardware. Make small pencil marks on the uprights desired working height.
Page 25
SMS CORD WRAP BARCKET AND CORD MANAGEMENT CHANNEL Install 5/16-18 x .75 square head bolts (item H), 5/16 flat washer (item D), and 5/16-18 hex head keps nuts (item J) to the cord wrap bracket (item L). Do not tighten this hardware.
Page 26
SMS LOWER SHELF Assembly Drawing SMS Lower Shelf Parts List Item Part# Description 16426802 Wksf 22dx 28l Std Shelf SMS T mold 29600411 Brkt,SMS Wksf/Shelf Supt Right 29600412 Brkt,SMS Wksf/Shelf Supt Left Item Part# Description 900080 Washer, 5/16 Flat Black 900230 Screw, 1/4-20 x .625 PPH MS Black 900068...
Page 27
SMS LOWER SHELF Installation nstall 5/16-18 x .75 square head bolts (item D), 5/16 flat washer (item A), and 5/16-18 hex head keps nuts (item E) to the top support brackets for the shelf (items 2 and 3) as shown . Do not tighten this hardware.
Page 28
SMS LOCKER Installation Mount the long front hanger bracket (item R) to the bottom of the worksurface. There are threaded inserts 10-1/8" about 1-3/4" from the front edge of the worksurface. Use 1/-20 Phillips head screws and flat washers (item N and P) to secure the bracket to the worksurface.
Page 29
ESD GROUNDING: ESD refers to the OPTIONAL static dissipative laminate used on the bench. The laminate has a conductive under layer that comes in contact with the factory installed grounding bolts in the worksurface. The ESD grounding kit, including the 10 ft. grounding wire must be attached and the bench must be properly grounded to your facility earth ground.
Page 30
SMS S4 SMART MOBILE STATION UE IAC INDUSTRIES 895 BEACON STREET BREA, CA 92821-2926 Phone (713) 990-8997 Fax (714) 990-0557 REVISON 112012 www.iacindustries.com...
Page 31
ATTENTION IAC Industries takes great care in the packing of it's products, however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order.
Page 33
SMS S4 Parts List ( See Page 3 ) Item Part# Description 21700101 SMS Upright Sub-assembly UE 60L 10422001 Worksurface 26D x 28L STD T-Mold 29601201 SMS Base Sub-Assembly Basic 29600411 SMS Worksurface Support RT 29600412 SMS Worksurface Support LT 16426802 Worksurface 22D x 28L Std Shelf SMS 44501008...
Page 34
SMS S4 Parts List ( See Page 3 ) Hardware Kit HWR521 Item Part# Description 900230 Screw, 1/4-20 x .625 PPH MS Black 900041 Bolt, 5/16-18 x .750 SQHD Black 900080 Washer, 5/16 Flat Black 900115 Nut, 5/16-18 Hex Keps Black 35111201 Brkt, CPU Holder Uprt MTD SMS Hardware Kit HWR031...
Page 35
SMS BASE / UPRIGHT ASSEMBLY SMS UPRIGHT SUB-ASSEMBLY ELECTRICAL OUTLETS SMS UPRIGHT POWERCORD LAMINATE PANELS REMOVED IN THE FRONT AND REAR SMS BASE POWERCORD SMS MAIN POWERCORD Install the casters to the SMS base. Thread the 1/2-13 hex nuts all the way onto the stems of the casters. Then thread the caster stems into the threaded inserts in the SMS base.
Page 36
SMS S4 Worksurface and Shelf Installation nstall 5/16-18 x .75 square head bolts (item F), 5/16 flat washer (item B), and 5/16-18 hex head keps nuts (item G) to the top support brackets for the worksurface and the shelf (items 2 and 3) as shown .
Page 37
SMS S4 Keyboard Tray and 12" Locker Installation Remove the keyboard tray. Pull the tray out until it stops. On the side of the drawer slides are plastic levers. Pull the left lever up while pressing the right lever down. This disengages the slides to allow the complete removal of the keyboard tray.
Page 38
SMS S4 Cord Wrap Bracket & Cord Management Channel The shelf is not shown as installed here. This allows the installation of the Cord Wrap Bracket and the LAN Wire Management Channel to be seen more clearly. Install 5/16-18 x .75 square head bolts (item F), 5/16 flat washer (item B), and 5/16-18 hex head keps nuts (item G) to the cord wrap bracket (item J).
Page 39
SMS S4 FPD Swing Arm Assembly Fig. A Fig. B See Fig A above: Uses Hardware Kit HWR531. Install 5/16-18 x .75 square head bolts (item T), 1/4 flat washer (item V), and 5/16-18 hex head Acorn nuts (item W) to the D4 Swing Arm Mtg Plt Assy (item 11).
Page 40
SMS S4 CPU Holder Assembly There are two CPU Holder Brackets (item S) in Hardware Kit HWR521. the Brackets mount to both sides of the upright. Install the square head bolts (item P), hex nuts (item R), and washers (item Q) as shown at left. Do not tighten this hardware.
Page 41
ESD GROUNDING: ESD refers to the OPTIONAL static dissipative laminate used on the bench. The laminate has a conductive under layer that comes in contact with the factory installed grounding bolts in the worksurface. The ESD grounding kit, including the 10 ft. grounding wire must be attached and the bench must be properly grounded to your facility earth ground.
Page 42
SMS S5 SMART MOBILE STATION UE IAC INDUSTRIES 895 BEACON STREET BREA, CA 92821-2926 Phone (713) 990-8997 Fax (714) 990-0557 REVISON 112012 www.iacindustries.com...
Page 43
ATTENTION IAC Industries takes great care in the packing of it's products, however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order.
Page 45
SMS S5 Parts List ( See Page 3 ) Item Part# Description 21700101 SMS Upright Sub-assembly UE 60L 10422001 Worksurface 26D x 28L STD T-Mold 29601201 SMS Base Sub-Assembly Basic 29600411 SMS Worksurface Support RT 29600412 SMS Worksurface Support LT 44501008 LAN Wire Management Channel 27.88L 35000801...
Page 46
SMS S5 Parts List ( See Page 3 ) Hardware Kit HWR521 Item Part# Description 900230 Screw, 1/4-20 x .625 PPH MS Black 900041 Bolt, 5/16-18 x .750 SQHD Black 900080 Washer, 5/16 Flat Black 900115 NUT, 5/16-18 HEX KEPS BLACK 35111201 Brkt, CPU Holder Uprt MTD SMS Hardware Kit HWR522...
Page 47
SMS BASE / UPRIGHT ASSEMBLY SMS UPRIGHT SUB-ASSEMBLY ELECTRICAL OUTLETS SMS UPRIGHT POWERCORD LAMINATE PANELS REMOVED IN THE FRONT AND REAR SMS BASE POWERCORD SMS MAIN POWERCORD Install the casters to the SMS base. Thread the 1/2-13 hex nuts all the way onto the stems of the casters. Then thread the caster stems into the threaded inserts in the SMS base.
Page 48
SMS Worksurfcae Installation Install 5/16-18 x .75 square head bolts (item H), 5/16 flat washer (item D), and 5/16-18 hex head keps nuts (item J) to the top support brackets items (4 and 5) as shown at left . Do not tighten this hardware. Make small pencil marks on the uprights desired working height.
Page 49
SMS S5 Keyboard Tray Installation There are threaded inserts in the bottom of the worksurface that align with the slots in the top of the Keyboard Tray Case (item 7). Place the Keyboard Tray Case against the bottom of the worksurface. Align the slots and the inserts.
Page 50
SMS S5 Cord Wrap Bracket & Cord Management Channel The shelf is not shown as installed here. This allows the installation of the Cord Wrap Bracket and the LAN Wire Management Channel to be seen more clearly. Install 5/16-18 x .75 square head bolts (item F), 5/16 flat washer (item B), and 5/16-18 hex head keps nuts (item G) to the cord wrap bracket (item J).
Page 51
SMS FPD Mounting Front UPR MTD Assembly Drawing For 75MM Mounting Hole Pattern (2.95") For 100MM Mounting Hole Pattern (3.94") SMS FPD Mounting Front Upr MTD Parts List Item Part# Description 38480001 D4 FPD Pivot Swivel Sub-Assy 38450301 SMS FPD Monitor Mtg Brkt Sub-Assy Front Hardware Kit HWR522 Item Part#...
SMS FPD Mounting Front UPR MTD Installation Install 5/16-18 x .75 square head bolts (item B), 5/16 flat washer (item C), and 5/16-18 hex head keps nuts (item D) to the monitor bracket(item 2) . Do not tighten this hardware. Install the Monitor bracket by installing the square head bolts (item 2) into the milled slots in the front nut channels of...
Page 53
SMS S5 CPU Holder Assembly There are two CPU Holder Brackets (item S) in Hardware Kit HWR521. the Brackets mount to both sides of the upright. Install the square head bolts (item P), hex nuts (item R), and washers (item Q) as shown at left. Do not tighten this hardware.
ESD GROUNDING: ESD refers to the OPTIONAL static dissipative laminate used on the bench. The laminate has a conductive under layer that comes in contact with the factory installed grounding bolts in the worksurface. The ESD grounding kit, including the 10 ft. grounding wire must be attached and the bench must be properly grounded to your facility earth ground.
Page 55
SMS S8 SMART MOBILE STATION UE IAC INDUSTRIES 895 BEACON STREET BREA, CA 92821-2926 Phone (713) 990-8997 Fax (714) 990-0557 REVISON 112012 www.iacindustries.com...
Page 56
ATTENTION IAC Industries takes great care in the packing of it's products, however damage can occur during shipment. Check all packages and parts for any signs of damage. If damage is evident STOP and contact the carrier that delivered your order.
Page 58
SMS S8 Parts List ( See Page 3 ) Item Part# Description 21700101 SMS Upright Sub-assembly UE 60L 10422101 Worksurface 26D x 28L STD T-Mold 29601201 SMS Base Sub-Assembly Basic 29600411 SMS Worksurface Support RT 29600412 SMS Worksurface Support LT 44501008 LAN Wire Management Channel 27.88L 35000801...
Page 59
SMS S8 Parts List ( See Page 3 ) Hardware Kit HWR521 Item Part# Description 900230 Screw, 1/4-20 x .625 PPH MS Black 900041 Bolt, 5/16-18 x .750 SQHD Black 900080 Washer, 5/16 Flat Black 900115 NUT, 5/16-18 HEX KEPS BLACK 35111201 Brkt, CPU Holder Uprt MTD SMS Hardware Kit HWR522...
Page 60
SMS BASE / UPRIGHT ASSEMBLY SMS UPRIGHT SUB-ASSEMBLY ELECTRICAL OUTLETS SMS UPRIGHT POWERCORD LAMINATE PANELS REMOVED IN THE FRONT AND REAR SMS BASE POWERCORD SMS MAIN POWERCORD Install the casters to the SMS base. Thread the 1/2-13 hex nuts all the way onto the stems of the casters. Then thread the caster stems into the threaded inserts in the SMS base.
Page 61
SMS S8 Worksurface and Shelf Installation nstall 5/16-18 x .75 square head bolts (item F), 5/16 flat washer (item B), and 5/16-18 hex head keps nuts (item G) to the top support brackets for the worksurface and the shelf (items 2 and 3) as shown .
Page 62
SMS S8 Keyboard Tray Installation There are threaded inserts in the bottom of the worksurface that align with the slots in the top of the Keyboard Tray Case (item 7). Place the Keyboard Tray Case against the bottom of the worksurface. Align the slots and the inserts.
Page 63
SMS S8 Drawer to Keyboard Tray Installation Line the slots on the top of the drawer assembly (Item 11) with the slots on the bottom of the keyboard tray assembly (item 7). Using nuts and washers (Items G and R) on the inside on the keyboard tray and screws and washers from (Items F and G) inside of the drawer, attach the drawer to the bottom of the keyboard tray.
Page 64
SMS S8 Cord Wrap Bracket & Cord Management Channel The shelf is not shown as installed here. This allows the installation of the Cord Wrap Bracket and the LAN Wire Management Channel to be seen more clearly. Install 5/16-18 x .75 square head bolts (item F), 5/16 flat washer (item B), and 5/16-18 hex head keps nuts (item G) to the cord wrap bracket (item J).
Page 65
SMS FPD Mounting Front UPR MTD Assembly Drawing For 75MM Mounting Hole Pattern (2.95") For 100MM Mounting Hole Pattern (3.94") SMS FPD Mounting Front Upr MTD Parts List Item Part# Description 38480001 D4 FPD Pivot Swivel Sub-Assy 38450301 SMS FPD Monitor Mtg Brkt Sub-Assy Front Hardware Kit HWR522 Item Part#...
Page 66
SMS FPD Mounting Front UPR MTD Installation Install 5/16-18 x .75 square head bolts (item V), 5/16 flat washer (item W), and 5/16-18 acorn head keps nuts (item X) to the monitor bracket (item 2) . Do not tighten this hardware. Install the Monitor bracket by installing the square head bolts (item 2) into the milled slots in the front nut channels of...
Page 67
SMS S8 CPU Holder Assembly There are two CPU Holder Brackets (item S) in Hardware Kit HWR521. the Brackets mount to both sides of the upright. Install the square head bolts (item P), hex nuts (item R), and washers (item Q) as shown at left. Do not tighten this hardware.
Page 68
ESD GROUNDING: ESD refers to the OPTIONAL static dissipative laminate used on the bench. The laminate has a conductive under layer that comes in contact with the factory installed grounding bolts in the worksurface. The ESD grounding kit, including the 10 ft. grounding wire must be attached and the bench must be properly grounded to your facility earth ground.