Related Manuals for Cobalt Digital Inc OGCP-9000
Summary of Contents for Cobalt Digital Inc OGCP-9000
- Page 1 OGCP-9000 Remote Control Panel Product Manual Cobalt Digital Inc. 2506 Galen Drive Champaign, IL 61821 Voice 217.344.1243 • Fax 217.344.1245 www.cobaltdigital.com OGCP-9000-OM (V2.5)
- Page 2 Furthermore, Cobalt Digital Inc. reserves the right to make changes to any products herein to improve readability, function, or design. Cobalt Digital Inc. does not assume any liability arising out of the application or use of any product or circuit described herein.
- Page 3 Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Warning Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Page 4 (Français) Consignes de sécurité importantes Lisez ces consignes. Conservez ces consignes. Observez tous les avertissements. Suivez toutes les consignes. N'utilisez pas cet appareil près de l'eau. Nettoyez l'appareil avec un chiffon sec uniquement. Avertissement N'installez pas l'appareil près d'une source de chaleur (radiateurs, bouches d'air, poêle, amplificateurs, etc.).
-
Page 5: Table Of Contents
Device and Parameter Submenu Overview ..........3-3 Selecting a Device ..................3-5 Displaying and Adjusting Device Parameters ..........3-6 System Information/User Interface Functions..........3-8 Loudness Metering Option ............... 3-12 Troubleshooting....................3-13 In Case of Problems.................. 3-14 OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... - Page 6 Overview ........................ A-1 Changing the Control Panel Network Settings ............A-2 Changing Frame Network Settings and/or Card Assignments....... A-5 Uploading a Configuration File to the Control Panel ........ A-5 Editing a Configuration File............... A-7 OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
-
Page 7: Chapter 1 Introduction
• Chapter 2, “Installation and Setup” – Provides instructions for installing the OGCP-9000 Remote Control Panel, and connecting the OGCP-9000 Remote Control Panel to the system in which it is intended to operate. • Chapter 3, “Operating Instructions” – Provides instructions for using the OGCP-9000 Remote Control Panel to monitor and control parameter values for cards. -
Page 8: Manual Conventions
Manual Conventions ® The OGCP-9000 is totally compatible with the openGear control software DashBoard™; any changes made with either system are reflected on the other. This chapter contains the following information: • Manual Conventions, p. 1-2 • Safety Summary, p. 1-4 •... -
Page 9: Labeling Symbol Definitions
Symbol (WEEE 2002/96/EC) For product disposal, ensure the following: • Do not dispose of this product as unsorted municipal waste. • Collect this product separately. • Use collection and return systems available to you. OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... -
Page 10: Safety Summary
Do not edit or alter the file contents preceding the ## start of Device Definitions ## section. CAUTION When performing the firmware update, use only the files provided by Cobalt Digital Inc. CAUTION and obtained as described here. - Page 11 • 3.75 x 2.25 in. W x H (95 x 57 mm) • 500 cd/m , 300:1 contrast ratio. Adjustable brightness. Controls • Eight control knobs; flexible function based on operating mode. • Numeric keypad and control buttons OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL...
-
Page 12: Warranty And Service Information
(1) year. Cobalt Digital Inc.'s (“Cobalt”) sole obligation under this warranty shall be limited to, at its option, (i) the repair or (ii) replacement of the product, and the determination of whether a defect is covered under this limited warranty shall be made at the sole discretion of Cobalt. -
Page 13: Contact Cobalt Digital Inc
Name and address of your local dealer • Product information and pricing • Technical support • Upcoming trade show information Phone: (217) 344-1243 Fax: (217) 344-1245 Web: www.cobaltdigital.com General Information: info@cobaltdigital.com Technical Support: support@cobaltdigital.com OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... - Page 14 This page intentionally blank OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
-
Page 15: Chapter 2 Installation And Setup
Place the Control Panel in rack mounting position. Start four 10-32 x 3/4 machine screws and nylon washers which secure the Control Panel to the rack. Evenly tighten the four Control Panel securing screws. OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... -
Page 16: Connecting The Control Panel Cabling
RJ-45 10/100 Ethernet connection to frame LAN TIA/EIA-232-F Connector DB-9 TIA/EIA-232 serial control/alarm port. Special use. Not used for typical installation. USB Connector Reserved for future use Figure 2-1 Control Panel Rear Panel Connectors OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5) - Page 17 Apply power to the cord connected to the Control Panel. ® Upon power-up verify that the COBALT opening screen (shown below) is shown on both Control Panel front panel screens. This verifies the Control Panel self-test. Proceed to Chapter 3,“Operating Instructions”. OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL...
- Page 18 This page intentionally blank OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
-
Page 19: Chapter 3 Operating Instructions
Note: • Values displayed at any time is the actual value as set on the card. OGCP_9000DL.PNG • Units characters (such as “dB” or “deg”) are displayed per ordered configuration preference and may not appear on some control panel displays. Figure 3-1 Basic Display/Knob Function OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... - Page 20 Rotate the knob to adjust the value of the displayed parameter. The parameter change is received by the device, with the current value displayed being the actual value as effected by the device. Figure 3-2 OGCP-9000 Remote Control Panel Controls and Displays OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
-
Page 21: Network Setup
Select devices (cards) and monitor/adjust the card parameters as described in this section. Device and Parameter Submenu Overview Each device has its user parameters organized into submenu groups, as shown in the example on the next page. OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... - Page 22 (Device list numbers 1 through 9 only.) When parameters are currently displayed jump directly to a different device by simply entering the device list number of the new device. Figure 3-3 Device and Parameter Submenu Overview OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
-
Page 23: Selecting A Device
The currently displayed parameter associated control knob submenu and its list order number device and its list order is shown here (“Phase”, being 1 of 8 parameters is shown here shown in this example) OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... -
Page 24: Displaying And Adjusting Device Parameters
3376_3377AL.PNG This display now shows submenu 2 items for the selected device. The parameter group 2 list order number and title is displayed (in this example, “2 HD and SD Scaler Settings”) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5) - Page 25 • Press the knob adjacent to the parameter (or press the key) to apply the change. Note: Out-of-range entries are indicated by red text being displayed. Press Cancel key to clear the entry. OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL...
-
Page 26: System Information/User Interface Functions
) appears, this indicates values cannot be changed in the currently displayed screen. Where the “P” icon ( ) appears, this indi- cates to press the adjacent knob to open the value for editing. OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5) - Page 27 Exit the Current Network Settings screen as follows: • Press the key to go to other Control Panel Submenu Select Submenu choices. • Press the key to exit the Control Panel Submenu. Select Device OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL...
- Page 28 Select Submenu key to save the changes and go to other User Interface submenu choices. • Press the key to save the changes and exit the User Select Device Interface submenu screen. 3-10 OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
- Page 29 • Greater settings allow for greater spans in value (major and minor) increment or decrement while knob is being rotated. • Lesser settings allow for smaller spans in value increment or decrement while knob is being rotated. 3-11 OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL...
-
Page 30: Loudness Metering Option
See “+LM Audio Loudness Meter Software” on our web site or catalog for more information. Note: Host card(s) and control panel(s) use separate option licensing as shown below. Figure 3-4 Typical Loudness Metering Display with Option +LM-P 3-12 OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5) -
Page 31: Troubleshooting
“Supplemental Information” for Control Panel configuration instructions. • Make certain the Control Panel Ethernet cable is properly connected and showing activity on the LAN switch. Use ping- to check the connection. 3-13 OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... -
Page 32: In Case Of Problems
The Cobalt Digital Inc. Technical Support Department will continue to provide advice on any product manufactured by Cobalt Digital Inc., beyond the warranty period without charge, for the life of the equipment. See Contact Cobalt Digital Inc., p. 1-7 in Chapter 1, “Introduction“for contact information. 3-14 OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5) -
Page 33: Appendix A Supplemental Information
Should the need arise to change any of the following, use the instructions in this appendix. • Changing the Control Panel Network Settings, p. A-2 • Changing Frame Network Settings and/or Card Assignments, p. A-5 OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... -
Page 34: Changing The Control Panel Network Settings
Press the Select Device key and then press the key. Press the key. The Control Panel Submenu selection Select Submenu screen is now displayed. Rotate any knob to select 2 Configure Network Settings OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5) - Page 35 Control Panel is to communicate with. Save changes by pressing the Select Device Select Submenu key. Saving Changes and Restarting is displayed. The Control Panel now ® restarts (followed by the power-up COBALT opening screen). OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL...
- Page 36 Rotate any knob to select 10.3 1 Current Network Settings Press any knob in to display current network settings. An 10.4 example of this display is shown below. 3398_3399LB.PNG OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
-
Page 37: Changing Frame Network Settings And/Or Card Assignments
Open a browser window and enter the Control Panel IP address on a computer connected to the frame LAN (“192.168.0.249” in the example shown below). When the screen shown below appears on the computer, click on Configuration File Upload. OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... - Page 38 The browser can now be closed. CAUTION Do not power down the Control Panel or disturb the upload until it is complete. Improper upload will result if upload is not allowed to properly complete. OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
-
Page 39: Editing A Configuration File
Panel by adding configuration content to the downloaded configuration file as follows: Note: For additional reference if desired, Figure A-3 on page A-10 shows an exam- ple configuration file and the resulting Control Panel configuration setup. OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL... - Page 40 Enter the banner text to be displayed for the Control Panel Select Device screen ( in Figure A-2). Enter any text as desired to help identify the Control Panel and its specific function. OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
- Page 41 • A saved configuration can be used to identically configure additional Control Panels if desired. OGCP-9000-OM (V2.5) OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL...
- Page 42 9361 9361 9061 Device 2 slot 5 slot 6 slot 7 slot 9 9821 slot 4 Device 1 OGCP-9000 9061 slot 2 3366_3392.JPG Figure A-3 Example Configuration File and Resulting Setup A-10 OGCP-9000 REMOTE CONTROL PANEL PRODUCT MANUAL OGCP-9000-OM (V2.5)
- Page 44 Cobalt Digital Inc. 2506 Galen Drive Champaign, IL 61821 Voice 217.344.1243 • Fax 217.344.1245 www.cobaltdigital.com OGCP-9000-OM (V2.5) Printed in USA...