Subscribe to Our Youtube Channel
Related Manuals for elho 10.2 Series
Summary of Contents for elho 10.2 Series
- Page 1 Series 10.2-10.4 ELHO Rake V-Twin 750 ELHO 941013 68910 BENNÄS ENGLISH Finland www.elho.fi Email: elho@elho.fi...
-
Page 2: Ec Declaration Of Conformity
Industrivägen 6 68910 Bennäs FINLAND We, the manufacturer of: ELHO V-TWIN 750 Rakes Serial number 10.2-10.4 Declare, that these machines fulfill the essential part of the following directives: 2006/42/EC In the design of the machines the following standards and regulations have been followed for... - Page 3 This limited warranty does not cover damages to the machine or its components caused, according the judgement of ELHO, by unsuitable hydraulics or electrical connections. As the use of ELHO products is outside of our control, we can only guarantee quality and do not accept liability in respect of performance.
-
Page 4: Identification Of Machine
Series Paint To ensure a long lifetime of the ELHO machines also the paint and painting process used at the manufacturing fulfil most strict international painting standards. However also a god paint surface might be damaged or scratched during transport and use. - Page 5 EC Directive 86-1888-EEC and UK Noise at Work Regulations 1989 place responsibilities on employers and employees to assess and control noise at the workplace. Bystander noise level of the ELHO V-TWIN 750 can exceed 87 dB (A) particularly if operated at full speed in an enclosed space.
-
Page 6: Technical Information
We reserve the right to alter specification details, dimensions, etc., without notice or liability. All data stated above is approximate. As ELHO rakes are supplied to many countries the detail specification may vary refer to local price list for specification offered and... - Page 7 VTwin - 750 Dimensions of V-Twin 750 Lifting of the machine The lifting points are marked with labels on the machine.
-
Page 8: Safety Instructions
Reduce speed when turning and driving on uneven ground. Use only original ELHO spare parts. The machine's construction must not be changed and the machine must only be used for mowing and swath laying grass crops. - Page 9 EC Directive 86-1888-EEC and UK Noise at Work Regulations 1989 place responsibilities on employers and employees to assess and control noise at the workplace. Bystander noise level of the ELHO V-TWIN 750 can exceed 87 dB (A) particularly if operated at full speed in an enclosed space.
- Page 10 1. This sign ask you to stop the engine, switch off the power, remove the start key and read the instructions before service or maintenance on the machine. he ELHO V-Twin are hydraulic driven. 2. This sign ask remain you t Take therefore particular care before any work on the machine as there might be full power also behind stopped or blocked rotors 3.
- Page 11 VTwin - 750 2.2.1 Safety sign positions on the machine...
- Page 12 VTwin - 750...
-
Page 13: Stop The Tractor
It is important that the greatest care is taken when starting up a new machine. Incorrect assembly, wrong operation etc. may cause damage, which is not covered by the ELHO warranty. The ELHO V-Twin 750 is connected to the 3-P linkage of the tractor (Kat II ). See § 5 Connecting to the tractor. - Page 14 Particular important this is for the wheel bolts. 4. Assembly The ELHO V-Twin rakes are generally delivered assembled and tested from the factory. Therefore no assembly work should be needed. Just check that the machine is delivered without transport damages.
- Page 15 Connect the hydraulic hoses. Start with ensuring a good connection for the free return line. The ELHO V-Twin rake is equipped with hydraulic couplings according to ISO 5676. It is unfortunately common that hydraulic quick-release couplings on different brands do not always suit each other to 100% although they are made to the same nominal size and mechanically fit in each other.
- Page 16 VTwin - 750 6. Adjustments 6.1 Raking height adjustment Normal setting is tine end 5 cm above the ground. Keep the setting as high as possible while still picking up crop. To set the initial raking height: • Open the rake on a level firm surface. •...
-
Page 17: Swath Width
VTwin - 750 6.3 Swath width. The swath width is set by crank E. Adjust left and right hand baskets to equal width. Do not mow the baskets more in than the rubber bumper still is outside the elbow F. Risk of interference between the hydraulic motor and the frame. - Page 18 VTwin - 750 6.6 Basket speed The basket speed is adjusted with the oil flow divider A. Normal basket speed is 80 - 100rpm. The slower the speed, the more gentle raking. Do not increase the basket speed over 110 rpm. Risk for major damage to the tine bars.
- Page 19 (not covered by the warranty). The maximum road speed for the ELHO V-Twin rake is 30 km/h. Observe the local legislation for transport on roads. In certain countries it may be necessary to equip the machine with a SMV triangle or rear lights and reflectors when driving on public roads.
-
Page 20: Maintenance
VTwin - 750 8. Maintenance To ensure a long and trouble free use of the machine, keep the machine clean and follow the maintenance instructions below. It is particular important to keep the hydraulic oil of the tractor clean and in god condition. Change the oil and the oil filter according the tractor manufacturers instruction . - Page 21 VTwin - 750 ELHO V-Twin Lubrication scheme...
-
Page 22: Lubrication Scheme
VTwin - 750 8.1 Lubrication scheme Grease daily with god quality grease 1 Basket front hub 2 pcs. 2 Basket shaft articulations 4 pcs. 3 Caster wheel swivels 4 pcs. Grease every 20 hours 4 Basket centre swivel point 2 pcs. 5 Basket lift cylinder bolts 4 pcs. - Page 23 VTwin - 750 Maintenance of Hydro Balance As the Hydro Balance system might be under pressure, always remove the system pressure before maintenance or repair. To remove the system pressure: • Connect only the hose nr. 5 (basket lift) to the tractor hydraulic. •...
-
Page 24: Optional Equipment
VTwin - 750 9. Optional equipment. 9.1 Rear light kit 114132 (Standard in several countries) The rear light kit is bolted to the foreseen mounting holes in the upper surface of the rear frame according picture below. The electrical connection is according ISO standard 1724. - Page 25 VTwin - 750 9.2.2 Content of the VT 750 S-kit To be able to perform the above described operation, the main components of the S-kit are: A. Hydraulic control unit B. Steering rod with wheel cylinder and limiter. C. Left hand bascet compensator cylinder. D.
- Page 26 VTwin - 750 • Set the machine in work position as normal. • Pull the rope connected to the hydraulic control unit of the VT 750 S-kit to open the hydraulic connections to the wheel cylinder and the left hand basket compensator cylinder.
- Page 27 VTwin - 750 9.3 Optional fingers 114129 The optional finger kit consist of 7+7 pcs steel fingers A (left and right) and 1 + 1 pcs. bars A (left & right). The fingers are mounted under the tine bare bearing bolts according the figure,.
- Page 28 VTwin - 750 9.4 Rake basket holding valve kit Order Nr. 114125 The rake basket holding valve kit make it possible to use the baskets individually. It is particular useful to; (A), - reposition a single short swath to be able to join it with the next pass, and so reduce driving damages of an heavy harvesting machine.
- Page 29 VTwin - 750 9.5 Hydraulic pump unit for rotor drive 114150 The hydraulic pump unit for the rotor drive consist of a tank, a gearbox with an hydraulic pump as well as necessary valves. The unit is mounted as in fig. At A there is already provided holes for the mounting bolts in the attachment frame.
- Page 30 VTwin - 750 Attachment I Hydraulic hose from relief valve for left basket cylinder The hydraulic hoses from the lift cylinders are dismantled has to be connected to T-junction (6). from the block and connected with a T-junction (2). The holes are plugged (3&...
Need help?
Do you have a question about the 10.2 Series and is the answer not in the manual?
Questions and answers