Page 1
User Manual Original Instructions Industrial Computers for Hazardous Locations Series H Catalog Numbers 6181X-12P2SWX1DC, 6181X-12A2SWX1DC, 6181X-00N2SWX1DC, 6181X-12A2SW71DC, 6181X-00N2SW71DC, 6189X-MCLPS, 6189X-8GDDR3, 6189X-16GDDR3, 6189V-CFSSD8GB, 6189V-CFSSD16GB, 6189X-128GBSSD, 6189X-256GBSSD, 6189X-PCIRISER, 6189X-SUNSHIELD...
Page 2
Important User Information Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Preface This manual is a user guide for 6181X Series H display and non-display industrial computers for hazardous locations. It provides procedures to the following: • Install the computer. • Make computer connections. • Operate the computer. • Troubleshoot the computer. Summary of Changes This publication contains new and updated information as indicated in this table.
Guidelines, publication 1770-4.1 system. You can view or download publications at https://www.rockwellautomation.com/global/literature-library/overview.page. To order paper copies of technical documentation, contact your local Allen-Bradley® distributor or Rockwell Automation sales representative. Abbreviations This publication uses the following abbreviations. Abbr Meaning Abbr Meaning...
Chapter Features Topic Page Operating Systems Computer Options Computer Nameplate Information Hardware Features Operating Systems The following Microsoft®-licensed operating systems are available: • Windows® 7 Professional (64 bit), SP 1 • Windows 10 Internet of Things (IoT) Enterprise (64 bit) To obtain a copy of a factory system image, contact your local technical-support center or access the Rockwell Automation Product Compatibility and Download Center (PCDC) at...
Chapter 1 Features This table summarizes the accessories that are available for industrial computers for hazardous locations. Table 2 - Available Accessories Cat. No. Description 6189X-MCLPS Replacement mounting clips (10) 6189X-8GDDR3 8 GB DDR3 RAM memory for extended temperature 6189X-16GDDR3 16 GB DDR3 RAM memory for extended temperature 6189V-CFSSD8GB CompactFlash card, 8 GB single-level cell (SLC) solid-state drive (SSD)
Features Chapter 1 Hardware Features Figure 1 shows the hardware features of the industrial computers for hazardous locations. An integrated display computer with a resistive touch screen is shown for illustrative purposes. Figure 1 - Industrial Computer for Hazardous Locations Front, Side, and Back Views Bottom View Item...
Page 12
Chapter 1 Features Notes: Rockwell Automation Publication 6181X-UM002B-EN-P - November 2019...
Chapter Install the Computer Topic Page Before You Begin Parts List Installation Precautions Installation Guidelines Mounting Clearance Requirements Computer Dimensions Tools for Computer Installation Install the Computer Connect Power Connect to a Network Before You Begin Before you unpack the computer, inspect the shipping carton for damage. If damage is visible, immediately contact the shipper and request assistance.
Chapter 2 Install the Computer Installation Precautions Read and follow these precautions before you install the computer. Environment and Enclosure Information ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in IEC 60664-1), at altitudes up to 2000 m (6561 ft) without derating.
Install the Computer Chapter 2 Outdoor Installation When you use a 6181X integrated display computer outdoors, consider the following to maximize the field life of the front bezel and display: • Select the proper enclosure • Computer orientation Ultraviolet (UV) and infrared radiation can reduce the field life of any electronic device.
Chapter 2 Install the Computer Hazardous Locations This equipment is suitable for these location categories. IMPORTANT 6181X computers can only be used in non-hazardous locations in any Eurasian Conformity region. Computer Cat. Nos. Region Rating Temperature Range Model Non-display 6181X-00N2SW71DC, United States Class I Division 2, Groups A, B, C, D T4 -20 °C <...
Page 17
Install the Computer Chapter 2 Power Specifications 6181X-12A2SW71DC, 6181X-00N2SW71DC, 6181X-12A2SWX1DC, Attribute 6181X-00N2SWX1DC 6181X-12P2SWX1DC Input voltage, DC 18…32V DC Power consumption, max Non-display models 18…32V DC (SELV), 2.22…1.25 A, 40 W Display models 18…32V DC (SELV), 2.78…1.56 A, 50 W 18…32V DC (SELV), 3.32…1.87 A, 60 W Heat dissipation Non-display models 40 W (136 BTU/h)
Chapter 2 Install the Computer • Transient protection shall be provided that is set at a level not exceeding 140% of the peak rated voltage value at the supply terminals to the equipment. • The ambient temperature (external to enclosure) range is -20…+55 °C (-4…+131 °F), and that of the internal enclosure ambient temperature is -20…+70 °C (-4…+158 °F).
Install the Computer Chapter 2 Restricted Access Location Verify that restricted access locations for the equipment meet these conditions: • Access is gained only by service personnel or by users who have been instructed on the reasons for restrictions to a location and about any precautions to be taken.
Chapter 2 Install the Computer Consider a user-supplied fan, heat exchanger, or air conditioner for heat that is generated by other devices in the enclosure. 70 °C (158 °F) max 70 °C (158 °F) max inside enclosure inside enclosure 55 °C (131 °F) max outside enclosure Restricted Access Location...
Install the Computer Chapter 2 Figure 2 - Minimum Clearances (display model shown) Item Description Clearance, min 50 mm (2 in.) Right (for airflow) 50 mm (2 in.) Rear 50 mm (2 in.) Left (for airflow and drive access) 127 mm (5 in.) Bottom (for I/O port access and ventilation) 102 mm (4 in.) Air Flow Direction Right and left are based on facing a computer from inside an enclosure.
Install the Computer Chapter 2 Panel Mounting Guidelines Observe these guidelines when you install the computer in a panel: • Remove all electrical power from the panel before making the cutout. • Verify that there is adequate space behind the panel. For specific information, see Mounting Clearance Requirements on page 20.
Page 24
Chapter 2 Install the Computer Follow these steps to mount the integrated display computer in a panel. 1. Remove power from the panel. 2. Verify that the panel surface around the area to be cut is clean and free of debris.
Install the Computer Chapter 2 Mount the Non-display Computer on a Wall Use the four supplied screws to secure the non-display computer to a metal wall, such as a steel panel in an enclosure or equipment room. IMPORTANT Do not mount the non-display computer on a horizontal surface. Follow these steps to mount a non-display computer.
Chapter 2 Install the Computer Connect Power Display and non-display computers have a DC input terminal block for connection to an 18…32V DC power source. ATTENTION: When you connect power to the computer for the first time, these actions occur: •...
Install the Computer Chapter 2 4. Secure the ground wire to the functional ground screw by using a ring connector. Tighten the functional ground screw at the torque value listed in the table in Installation Guidelines on page Ring Connector Functional Ground Screw IMPORTANT When using the functional ground screw, connect the computer to...
Page 28
Chapter 2 Install the Computer Notes: Rockwell Automation Publication 6181X-UM002B-EN-P - November 2019...
Chapter Operate the Computer Topic Page Operating Guidelines Touch Screen Precautions Start the Computer Restart the Computer Shut Down the Computer Adjust the Display Brightness Operating Guidelines Follow these operating guidelines for your computer: • When the computer is panel mounted, operator access is limited to the front of the computer, which includes the display and the touch screen.
Chapter 3 Operate the Computer Touch Screen Precautions WARNING: If the LCD screen darkens or if the backlight is not functioning properly, the screen can be difficult to read and use of this screen could result in a potentially hazardous outcome. Do not use the LCD touch screen under these circumstances.
Operate the Computer Chapter 3 Restart the Computer Use either of the following methods to restart the computer: • From the Start menu, choose Restart. • Press CTRL+ALT+DEL on an attached keyboard and click Restart. During a restart, the computer does the following: •...
Page 32
Chapter 3 Operate the Computer Notes: Rockwell Automation Publication 6181X-UM002B-EN-P - November 2019...
Record the model and serial number, and any other pertinent information of new components for future reference. IMPORTANT We recommend that you use only Allen-Bradley® approved accessories and replacement parts. Voltage Precautions The computers contain line voltages. Disconnect all power to the computer before you install or remove components.
Chapter 4 Replace Components Electrostatic Discharge ATTENTION: Electrostatic discharge (ESD) can damage static-sensitive devices Precautions or microcircuitry. • Before you work on the computer, disconnect all power as detailed in Voltage Precautions on page • To help prevent damage, observe proper packaging and grounding techniques. Follow these precautions: •...
Replace Components Chapter 4 Post-configuration Follow these steps after you install or remove a hardware component. 1. Make sure that all components are installed according to instructions. 2. Make sure that no tools or loose parts are left inside the computer. 3.
Chapter 4 Replace Components Replace a Solid-state Drive WARNING: The solid-state drive (SSD) bay on the side of all computer models is not hot-swappable. You must first shut down the computer before you can insert or remove an SSD tray from this bay. Do not connect or disconnect components unless power has been switched off and the area is known to be non-hazardous.
Replace Components Chapter 4 Load a CompactFlash Card The computers have one location to load a CompactFlash (CF) Type II card, which is the slot on the I/O port panel below the serial ports. This slot is functionally hot-swappable but only in a non-hazardous location. It is meant to be a data slot but it is bootable.
Chapter 4 Replace Components Install an Add-in Card IMPORTANT For hazardous locations, please note the following: • The integrated display computers with a resistive touch screen were evaluated for use with a PCIe add-in card. • The integrated display computer with a PCAP touch screen and non-display computers were evaluated for use with PCIe and PCI add-in cards.
Page 39
Replace Components Chapter 4 For a PCI add-in card: a. Remove the three screws that secure the add-in card tray. For the screw locations, see the figure in step b. Remove the add-in card tray. c. Remove the two screws that connect the factory-supplied PCIe riser card to the add-in card tray.
Chapter 4 Replace Components Replace or Add Memory The computers have two dual-channel DDR3 SO-DIMM slots that support up to 16 GB maximum system memory. Modules IMPORTANT Both memory slots must be populated with memory modules of the same capacity. All 6181X computers ship with a dual memory module configuration. All memory module upgrades in Table 2 on page 10 ship with heatsinks.
Replace Components Chapter 4 4. Remove the existing memory modules. a. Use your thumbs or two fingers to push open the lock levers, which release each memory module from its slot for easy removal; see step b. Gently pull out each memory module to remove it from its slot. c.
Chapter Set Up the UEFI Utility Topic Page Set-up Utility Overview Access the Set-up Utility Set-up Screen Overview Firmware Update Firmware Configuration Diagnostics AMI Rescue Hardware History Exit Set-up Utility Overview The set-up utility is a hardware configuration program that is built into the universal extensible firmware interface (UEFI).
Chapter 5 Set Up the UEFI Utility Access the Set-up Utility Follow these steps to access the set-up utility in your computer. 1. Start your computer. 2. During POST, you have two selections to access the set-up utility. Press Result Accesses a graphical interface of set-up environment.
Set Up the UEFI Utility Chapter 5 Firmware Update You can update your system firmware from the Firmware Update menu. Parameter Description Browse Click to navigate to the firmware file saved onto a media. Firmware file location Select or type the file name for the firmware file. Flash Click to start the BIOS programming.
Chapter 5 Set Up the UEFI Utility Firmware Configuration You can view and modify the various system parameters from the Firmware Configuration menu. On the left are six menu options that are stacked vertically. Menu Description Main Use this menu to view general computer information and for basic system configuration.
Set the system time. Format: HH:MM:SS (Hour:Minute:Second) Runtime Hours Records the total hours of computer runtime. Manufacturer System manufacturer Catalog Number Allen-Bradley® catalog number with series letter WIN Number Warranty information number Version-SYS System version, manufacture date Version-Board System board version information...
Chapter 5 Set Up the UEFI Utility Advanced Enable PXE Boot When PXE boot is enabled, a computer boots from a server on a network before it boots the operating system on the local storage drive. Parameter Description Enable PXE Boot Enables or disables boot option for legacy network devices.
Page 49
Set Up the UEFI Utility Chapter 5 CPU Configuration Parameter Description CPU Configuration Displays processor type and maximum speed. Processor Cores Displays processor core count. CPU Speed Displays maximum speed of the processor. 64 bit Displays 64 bit support status. Hyper-threading Enables or disables the hyper-threading technology.
Page 50
Chapter 5 Set Up the UEFI Utility SATA Configuration (AHCI and RAID modes) Parameter Description SATA Mode Selection Select an operation mode for the onboard SATA controller. Options: AHCI (default) or RAID SATA Port (0, 1) Indicates the SATA drive that is connected to the SATA connector. Port (0, 1) Enables or disables the SATA drive that is connected to the SATA port.
Page 51
Set Up the UEFI Utility Chapter 5 Super I/O Configuration Parameter Description Super I/O Chip Displays the Super I/O chipset information. Serial Port 1 Configuration Select to set parameters for serial port 1. Serial Port 2 Configuration Select to set parameters for serial port 2. Returns you to Firmware Configuration set-up screen;...
Page 52
Chapter 5 Set Up the UEFI Utility Hardware Monitor Parameter Description CPU temperature DIMM1 temperature DIMM2 temperature Vcore Temperature MB Temperature VCORE_S0_CPU V1D05_S0 V1D5_S0 V12D0_S0 VDDQ_S3_MEM V3D3_S0 V5D0_S0 Displays the current temperatures (in °C) and core voltages of various hardware components.
Set Up the UEFI Utility Chapter 5 Chipset Parameter Description Adjust Backlight Adjust the internal LCD light-emitting diode (LED) backlight brightness. Number range: 1…100 with 100 as full (100%) brightness; 70 is default. IMPORTANT: Increasing the brightness from the default setting reduces the life of the LED backlight, particularly at high temperatures.
Chapter 5 Set Up the UEFI Utility Boot Parameter Description Bootup NumLock State Enables or disables the Num Lock key on boot. Option: On (default) or Off Quiet Boot Enables or disables Quiet Boot option. Option: Enabled or Disabled (default) IMPORTANT: When enabled, this option hides the POST screen messages at computer startup.
Set Up the UEFI Utility Chapter 5 Security Parameter Description Administrator Password Sets the administrator password. Use this password to minimize assess risk from unauthorized or malicious sources. IMPORTANT: If you forget the administrator password, there are two ways to reset •...
Chapter 5 Set Up the UEFI Utility Diagnostics The Diagnostics menu runs the diagnostics utility to determine the cause of the system malfunction by testing computer components, such as the processor, memory, drives, video, and other hardware. Select a menu option by pressing the upor down arrow keys and pressing Enter when a menu is highlighted.
Set Up the UEFI Utility Chapter 5 AMI Rescue The AMI Rescue menu lets you back up the system image on your computer and restore that image. IMPORTANT The following instructions are for the built-in backup and restore utility, AMI Rescue.
Chapter 5 Set Up the UEFI Utility Make a Backup Follow these steps to back up the system image. IMPORTANT Attach a FAT32-formatted USB storage device to the computer before you perform these steps. Use a USB storage device that is appropriately sized for the amount of data being backed up.
Set Up the UEFI Utility Chapter 5 6. Click OK. 7. Click Exit. 8. In the Destination of Image File field, click Browse to locate the destination source. 9. From the List of Volumes menu, select the external USB drive. IMPORTANT Do not select Recovery;...
Page 60
Chapter 5 Set Up the UEFI Utility 3. In the Source of Image File field, click Browse to locate the image source. 4. From the List of Volumes menu, select Recovery. IMPORTANT Recovery is the default OS image source, which is the hidden partition on your internal storage drive.
Page 61
Set Up the UEFI Utility Chapter 5 7. From the List of Labels menu, select the default destination. IMPORTANT The Label name is similar or identical to the above example. 8. Click Advanced. 9. On the Select Partition screen, select all boxes for Disk 0 so the entire OS image is restored.
Chapter 5 Set Up the UEFI Utility 12. Click Restore Now to start the restoration process. IMPORTANT The following warnings can appear: If prompted, click Yes to continue. If prompted, click Yes to continue. If prompted, click No to continue. If prompted, click Yes to continue.
Page 63
Set Up the UEFI Utility Chapter 5 3. In the Source of Image File field, click Browse to locate the image source. 4. From the List of Volumes menu, select the USB storage drive. IMPORTANT Do not select Recovery; it is the OS image on the computer that you wish to restore.
Page 64
Chapter 5 Set Up the UEFI Utility 7. From the List of Labels menu, select the USB storage drive. IMPORTANT If no labels are visible, then the backed-up OS image folder must be moved to the root directory of the USB storage drive. The backup is automatically assigned a name based on the system date, such as ‘03172016_00.’...
Page 65
Set Up the UEFI Utility Chapter 5 12. Click Restore Now to start the restoration process. IMPORTANT The following warnings can appear: If prompted, click Yes to continue. If prompted, click Yes to continue. If prompted, click No to continue. If prompted, click Yes to continue.
Chapter 5 Set Up the UEFI Utility Hardware History You can view various hardware parameters from the Hardware History menu. It shows the total hours that the computer has been powered up, or runtime. It also displays the minimum and maximum temperatures (in °C) over the entire runtime. All displayed values are read-only, and the time stamp is 24-hour clock.
Set Up the UEFI Utility Chapter 5 Exit Use the Exit menu to close the UEFI set-up utility. Rockwell Automation Publication 6181X-UM002B-EN-P - November 2019...
Chapter 5 Set Up the UEFI Utility Upgrade to a New UEFI Sometimes a new UEFI (BIOS) is released to enhance the performance of your computer or to correct an anomaly. In such cases, you can download BIOS upgrades at the Rockwell Automation® Product Compatibility and Download Center (PCDC) website at http://compatibility.rockwellautomation.com/ Pages/home.aspx.
Chapter Troubleshoot the System Topic Page Hardware Monitoring Troubleshooting Diagnostics Load the System Defaults Clear the CMOS Ship or Transport the Computer Dispose of the Computer Hardware Monitoring The built-in hardware monitor of the computer tracks the operating threshold levels of the voltage and temperature sensors. Follow these steps to determine whether an operating threshold has been reached.
Chapter 6 Troubleshoot the System Troubleshooting WARNING: Before performing any maintenance procedures, review the safety information in Hazardous Locations on page 16 for equipment that is used in hazardous locations. Follow these steps to identify and isolate an issue with the computer. 1.
Troubleshoot the System Chapter 6 Follow these steps to save diagnostic reports. Use the arrow keys on a keyboard to navigate between UEFI menus and menu selections. 1. Select Generate Report in the Options menu and press Enter. 2. Select Report destination and press Enter. 3.
Chapter 6 Troubleshoot the System Clear the CMOS You must clear the system configuration values that are stored in the CMOS if the following conditions are present: • The system configuration has been corrupted • An incorrect setting has caused error messages to be unreadable •...
Troubleshoot the System Chapter 6 6. Use a conductive tool (such as a screwdriver) to make contact between the two pins for 10 seconds. 7. Follow the steps for Post-configuration on page IMPORTANT When you clear the CMOS, all UEFI settings return to their defaults. UEFI settings other than default must be reconfigured after clearing the CMOS.
Page 74
Chapter 6 Troubleshoot the System Notes: Rockwell Automation Publication 6181X-UM002B-EN-P - November 2019...
Chapter Use a Touch Screen Topic Page Touch Screen Technology Touch Screen Operation Calibrate the Resistive Touch Screen Touch Screen Technology 6181X integrated display computers have either resistive or PCAP touch screens. Resistive Touch Screen Displays The Cat. Nos. 6181X-12A2SW71DC and 6181X-12A2SWX1DC integrated display computers are shipped with the resistive touch screen displays.
Chapter 7 Use a Touch Screen Touch Screen Operation Resistive touch screens are activated when you apply pressure to the touch screen with your finger. You can operate a resistive touch screen while gloves are worn. PCAP touch screens are activated with conductive touch of a human finger. You can operate a PCAP touch screen while gloves are worn.
Chapter Maintain the Computer Topic Page Clean the Computer Rinse with clean water. Clean the Computer It is important to maintain your computer. Periodically clean the display, heatsink and vent holes, and remove any grease or paint. Clean the Integrated Display Follow these steps to clean the display.
Chapter 8 Maintain the Computer Remove Paint and Grease from the Bezel Follow these steps to remove paint and grease from the bezel of computers that are properly mounted in NEMA Type 4/4X or IEC IP66 enclosures. 1. Remove paint splashes and grease by rubbing lightly with isopropyl alcohol.
Page 79
Index accessories 33 Firmware Configuration add-in card 38 Advanced 48 Boot 54 Chipset 53 Main 47 Save & Exit 55 BIOS Setup utility Security 55 access 44 Setup screen 44 hardware features 11 calibrating touch screen 76 hardware diagnostics 69 cleaning the computer hardware monitor 69 chassis 77...
Page 80
Index panel cutout dimensions 23 Setup menu panel mounting AMI Rescue 57 Diagnostics 56 guidelines 23 Exit 67 parts list 13 Firmware Configuration 46 PCI 38 Firmware Update 45 power system applying 26 defaults 71 precautions 26 turn on 30 turn on 30 voltage precaution 33 Power On Self Test 30...
Page 81
Index Notes: Rockwell Automation Publication 6181X-UM002B-EN-P - November 2019...
Page 82
Index Notes: Rockwell Automation Publication 6181X-UM002B-EN-P - November 2019...
Page 84
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, LAN/1, and Rockwell Automation are trademarks of Rockwell Automation, Inc. EtherNet/IP is a trademark of ODVA, Inc. Intel is a trademark of Intel Corporation. Microsoft and Windows are trademarks of Microsoft Corporation.