Table of Contents
Advertisement
Quick Links
FCC Part 15 C Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
WARNING!
CHOKING HAZARD - Small parts.
Not suitable for children under 3 years.
Conforms to safety requirements of FCC.
This product is manufactured by AMAX Industrial Group
12645 Memorial Drive Suite F1 #388 Houston, TX 77024
Propel™ and Propel RC™ are the licensed trademarks of Rooftop Group LTD Singapore.
2008 All rights reserved. Visit us at www.propelrc.com
MAXIMUM™ is the property of Eastern Design Group, USA.
2017 All rights reserved.
11
WARNING: Never leave product charging unattended for extended periods of
time. Always disconnect TWISTER™ from charger immediately after the
TWISTER™ is fully charged. Please refer to enclosed safety instructions.
TWISTER™
Made in China
V 1.0
TWISTER
High Performance Stunt Drone
INSTRUCTION BOOKLET
PACKAGE CONTAINS:
2.4G Wireless Controller
USB Charging Cord
Colors and styles may vary slightly
™
Spare Parts
Instruction Booklet
BC
Advertisement
Table of Contents
Related Manuals for Propel Trampolines TWISTER
Summary of Contents for Propel Trampolines TWISTER
- Page 1 WARNING: Never leave product charging unattended for extended periods of time. Always disconnect TWISTER™ from charger immediately after the WARNING! TWISTER™ is fully charged. Please refer to enclosed safety instructions. CHOKING HAZARD - Small parts. Not suitable for children under 3 years.
-
Page 2: Table Of Contents
Caution: The USB charging socket fits the plug only in one way. Do not force it. Connect the TWISTER™ charging cord to your computer’s USB port or a USB wall charger (See diagram B). 3. Average charging time is about 50-60 minutes. The flashing red LED indicator turns ON when battery is fully charged. -
Page 3: Twister™ Quadrocopter Diagram
• Make sure to be in a large space with an open radius of at least 50 feet. ON/OFF Button • Make sure the empty space has no obstacles or bodies of water. Set your TWISTER™ on a clean flat surface before take-off. Power Indicator DO NOT ATTEMPT TO FLY YOUR TWISTER™... -
Page 4: Automatically Take Off / Land
• If your TWISTER™ banks to the left, push and release the R TRIM button repeatedly until the banking stops and proper flight is maintained. • If your TWISTER™ banks to the right, push and release the L TRIM button in the same manner until the problem is resolved. -
Page 5: Basic Flight Control
If the TWISTER™ becomes unstable during the course of fly your TWISTER™ it is best to start with a large space until you get used to the basic controls. As you flying, you may need to calibrate the internal gyros. To do master flying your TWISTER™... -
Page 6: Twister™ Warnings
Stand away from the TWISTER™ to reduce the risk of getting into the flight path. Warn spectators that you will be flying your TWISTER™ so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the TWISTER™.
Need help?
Do you have a question about the TWISTER and is the answer not in the manual?
Questions and answers