Advertisement
Quick Links
Advertisement
Related Manuals for STACKHAUS MAGIC CORNER PRO
Summary of Contents for STACKHAUS MAGIC CORNER PRO
- Page 1 MAGIC CORNER PRO User Manual Play Setup Video English...
- Page 2 INTRODUCTION Introducing the Magic Corner Pro assembly manual. In this manual, we will show you how to assemble your own Magic Corner Pro. Before beginning the assembly, make sure that there is ample room for installing and assembling your product. Please check the following chart to ensure the product size exactly suits your cabinet based on the following dimensions.
- Page 3 PARTS & TOOLS CHECK LIST Ensure that the following parts are included with your Magic Corner Pro. These are crucial components that will be the mainframe of your entire assembly. The following tools are recommended for this installation. Cabinet x1...
- Page 4 PARTS & TOOLS CHECK LIST Ensure that the following parts are included with your Magic Corner Pro. These are crucial components that will be the mainframe of your entire assembly. The following tools are recommended for this installation. Part 7 x1...
- Page 5 Dimensions of your cabinet may vary, but should be within a set average height. Please refer to the next page for furhter information. Part 7 Part 7 is essential for the Magic Corner Pro’s functionality of opening and closing the com- partment.
- Page 6 Magic Corner Pro that best suites your cabinet’s measurements. The dimensions of the Magic Corner Pro are listed below. The measurements of the cabinet shown below are a minimum and does not necessarily reflect the final product’s dimensions.
- Page 7 INSTRUCTIONS Step 2 - Aligning the Drilling Template Locate the drilling template Begin Step Two by locating the Drilling Template and place it in the location you wish to pre-drill the holes. The template can be used to align for a left sided orientation, or a right sided orientation, depending on your preference.
-
Page 8: Step 3 - Installing The Inner Frame
INSTRUCTIONS Step 3 - Installing the Inner Frame Locate the inner frame components Begin Step Three by locating the inner frame components ( one Part 1b, one Part 2a, one Part 2b, and two Part 4 ) and attach them in the orientation shown. - Page 9 INSTRUCTIONS Step 4 - Installing the Side Swivel Frame Locate the Part 5 and Part 6 components and se- cure together Begin Step Four by locating the Part 5 and Part 6 components and align them, as shown. Secure the Part 6 component using one Part 10 screw. Extend the frame outward and align the newly formed assembly Extend the frame outward, as shown, so that the bar extends outward.
- Page 10 INSTRUCTIONS Step 5 - Installing the Spinning Bottom Part Locate the Spinning Bottom Part Locate the Part 7 component and aling it to the bottom of the assembly from the previous step. Make sure that Part 7 is aligned accordingly to ensure proper functionality of the product.
- Page 11 INSTRUCTIONS Step 6 - Attaching the Cabinet Door Locate the Cabinet Door and drilling template Locate the Cabinet Door, and align the Drilling Template to the cabinet door, as shown. Depending on your preference, you can install the door to open from the right side, or open from the left side. Pre-drill nine holes using a Power Drill with Drill Bit, and remove the template afterwards.
- Page 12 INSTRUCTIONS Step 6 - Attaching the Cabinet Door Push Part 6 into the grooved section Next, push Part 6 into the grooved section of the cabinet door so that it snugly fits into place. Locate Part 9 and push into place Locate one Part 9 piece and push downward so that it snaps into place and secures the lower extending rail section from the main frame, as shown.
- Page 13 INSTRUCTIONS Step 7 - Adjusting the Cabinet Door Adjust the cabinet door You can adjust the cabinet door by loosening up the screws shown in the following locations and move the cabinet door left, right, back and forth, and up and down until proper alignment is achieved. Use a Phillips screwdriver to loosen and tighten the screws to keep the desired adjustment.
- Page 14 INSTRUCTIONS Step 6 - Installing the Baskets Locate two Part 12 baskets Locate two Part 12 baskets and align them to the following locations shown Attach the baskets and secure on the hooks Attach the baskets onto the hooks and slowly push into place. Adjust the necessary height as needed for each basket.
-
Page 15: Technical Support
Technical support www.stackhaus.com.au info@stackhaus.com.au © StackHaus 2019, All Rights Reserved...
Need help?
Do you have a question about the MAGIC CORNER PRO and is the answer not in the manual?
Questions and answers