Scheppach BCH5300BP Translation From The Original Instruction Manual page 28

4. Assemble and disassemble the cutting head
grass trimmer / nylon cutting head. Fig. 19 - 20
• Release the nut.
Line up the two holes of flange and shield, use
one screw driver to hold the flange as below and
turn the socket wrench clockwise, the nut will be
released.
• Fit the Nylon cutting head.
Remove another shield after release the nut. Still
hold the flange, take the Nylon cutting head on the
shaft and rotate counter-clockwise, the Nylon cut-
ting head is fitted. Fig. 20
• Release the Nylon cutting head.
Use screw driver to hold flange and then rotate the
Nylon cutting head clockwise, it will be replaced.
Brush cutter / Cutter blade
• Fit the blade. Fig. 16 - 18
Take the outer flange off after release the nut, then
put the blade (4), outer flange (25), shield (24) and
nut according to priority as below picture. Note
the blade rotation direction needs be same as be-
low picture. Use screw driver to hold flange and
tighten nut counter-clockwise, ensure the nut is
tightened enough.
• Release blade. Use screw driver to hold flange and
release nut, the blade can be took off.
5. Assemble the safe guard. Fig. 21 23
• Fix the safe guard with hex key and wrench en-
closed as stardard accessories for tighting the nuts
enough. Please see the below pictures showing.
m Warning! Use only original manufacturer's re-
placement parts, accessories and attachments. Fail-
ure to do so can cause poor performance, possible
injury and may void your warranty. Never use the
machine without the guard assembled!
m Warning!
Please make sure the cutting head has been assem-
bled correctly before use!
Note: The packaging material is made of recycle
materials. Dispose of packaging materials in accord-
ance with regulations.
6. Fit the belt. Fig. 25 - 29
• Wear the shoulder strap. Fig. 25 - 27
• Balance the machine when the tool is switched off.
• When standing in a normal working posture, the
blade should touch the ground during normal work-
ing position.
• To fit the backpacks to your body size adjust the
straps at the carrying strap. Fig. 29
• Safety button at the carrying strap Fig. 28
ATTENTION! In an emergency, the safety button
(m) can be pressed from the harness. The machine
then detaches immediately from the carrying strap
and falls to the ground.
28 GB
OPERATION
When working with the equipment, the appropriate
plastic guard hood for cutting blade mode or cutting
line mode must be fi tted to prevent objects being
thrown out by the equipment.
The integrated blade in the cutting line guard hood
automatically cuts the line to the optimum length.
Fig. 24
Filling with fuel
m Danger of injury! Fuel is explosive!
Turn off and cool the motor down before filling
the tank with fuel. You must observe all safety
instructions relating to handing fuel.
m Risk of device damage!
The device is supplied without motor or gear-
box oil.
ATTENTION! Before operating, you must fill it
with fuel.
• Unscrew the tank cap (B) and remove it. Fig. 32
• Pour in the fuel carefully. Avoid spilling!
• Screw the tank cap on firmly by hand.
Draining fuel. Fig. 47
• Hold a collection container beneath the fuel drain
bolt.
• Unscrew the tank cap (B) and remove it.
• Allow the fuel to run out completely.
• Screw the tank cap on firmly by hand.
Start on the unit
Do not start the unit until it has been completely as-
sembled.
m Danger of injury!
Do not operate the device unless you did not
find any faults. If a part has become defective,
make sure to replace it before you use the device
again.
Check before use!
• Check the safe condition of the device:
• Check the device for leaks.
• Check the device for visual defects.
• Check that all parts of the device have been se-
curely fitted.
• Check that all safety devices are in proper condi-
tion.
m Danger of injury!
Before starting work, always check the ground and
remove all objects which could be thrown by the de-
vice.
Start Fig. 30 - 34 + 48
Once the machine has been set up properly, start the
engine as follow:
1. Set the equipment down on a hard, level surface.