1. Manuals
  2. Brands
  3. Enerdrive Manuals
  4. Battery Charger
  5. ePower Industrial EPI-2430
  6. Operation / owner's manual

Enerdrive ePower Industrial EPI-2430 Operation / Owner's Manual

Multi stage battery charger
Hide thumbs Also See for ePower Industrial EPI-2430:
Table of Contents

Advertisement

Quick Links

Download this manual
Operation & Owner's Manual
24V, 36V & 48V Models
Rev: 1.2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ePower Industrial EPI-2430 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Enerdrive ePower Industrial EPI-2430

Summary of Contents for Enerdrive ePower Industrial EPI-2430

  • Page 1 Operation & Owner’s Manual 24V, 36V & 48V Models Rev: 1.2...
  • Page 2 CAUTION and WARNING statements. Disclaimer While every precaution has been taken to ensure the accuracy of the contents of this guide, Enerdrive assumes no responsibility for errors or omissions. Note as well that specifications and product functionality may change without notice.
  • Page 3 Shall in no event be liable to anyone for special, collateral, incidental, or consequential damages in connection with or arising out of purchase or use of these Enerdrive products. The sole and exclusive liability to Enerdrive, regardless of the form of action, shall not exceed the purchase price of the Enerdrive products described here in www.enerdrive.com.au...

  • Page 4: Table Of Contents

    6. WATERPROOFING INSTALLATION 7. SPECIFICATIONS 8. CHARGE PROFILE CHARGE PROFILE INSTRUCTIONS: CHARGE PROFILE TABLE: 9. WARRANTY 2 YEAR LIMITED WARRANTY: 3 YEAR PRO RATA SUPPORT PROGRAM: RETURN AND/OR REPAIR POLICY: LIMITATIONS: Page 4 Enerdrive ePOWER Industrial Battery Charger Owner’s Manual (Rev. 1.2)

  • Page 5: Introduction

    • Avoid moisture ingress. Never expose the unit to snow, water, etc. WARNING: EXPLOSION HAZARD! • DO NOT use the Enerdrive ePOWER Industrial Battery Charger in the vicinity of flammable fumes or gases (such as gas bottles or large engines).
  • Page 6 • Charger is not to be used by persons with reduced physical or mental capabilities or lack of knowledge and experience. Not to be operated or used by children. Page 6 Enerdrive ePOWER Industrial Battery Charger Owner’s Manual (Rev. 1.2)

  • Page 7: Product Description

    WARNING • Enerdrive recommends that all wiring be done by a skilled technician to ensure adherence to the best practice standards for on-board DC electrical installations. Failure to follow these instructions can damage the unit and could also result in personal injury or loss of life.

  • Page 8: Battery Capacity Indicators

    3 conductor, 1.5 mm² minimum, and rated appropriate for use in the country of destination. AC input type to the charger is, type IEC 60320 C14 plug. Page 8 Enerdrive ePOWER Industrial Battery Charger Owner’s Manual (Rev. 1.2)
  • Page 9 Interlock Cable ( When charger is charging, the interlock cables will form an open circuit with no voltage. When charger is not charging, the interlock cable will form a short circuit with no voltage) USB Terminal for Charge Profile settings www.enerdrive.com.au Page 9...

  • Page 10: Fault Indicator

    Check and assure that the correct output battery voltage is Battery voltage is too high connected. Battery voltage is too low Check that the correct output battery voltage is connected. Page 10 Enerdrive ePOWER Industrial Battery Charger Owner’s Manual (Rev. 1.2)

  • Page 11: Waterproofing Installation

    2. Connect the AC input cable into the charger ensuring the waterproofing ring is seated correctly 3. Firmly tighten the waterproofing clamp using a Phillips head screw driver *NOTE: Take care to not overtighten the waterproof clamp. www.enerdrive.com.au Page 11...

  • Page 12: Specifications

    Full Load AC Power Factor >0.98 Dimensions: 20.7x18.0x16.0 cm Weight 4.6kg Operating Temperature: - 30C ~ +50C Storage Temperature - 40C ~ +70C Note: Specifications are subject to change without notices. Page 12 Enerdrive ePOWER Industrial Battery Charger Owner’s Manual (Rev. 1.2)

  • Page 13: Charge Profile

    Please carefully follow the steps below to change the charge profile: - 1. Download and save the Battery Algorithm Listing from the download link www.enerdrive. com.au/Algorithm/ePOWER-algorithm.xlsx 2. Select a charge profile that matches the batteries you are using from the “Charge Profile Listing”...

  • Page 14: Charge Profile Table

    Flooded US. 12VXC2 Flooded Flooded US 305XC Flooded Flooded US 125 XC2 FLA Flooded US 145 XC2 FLA Flooded Crown Crown CR-235 FLA Flooded Crown Crown CR-245 FLA Flooded Page 14 Enerdrive ePOWER Industrial Battery Charger Owner’s Manual (Rev. 1.2)

  • Page 15: Warranty

    If such a unit is returned more than 30 days but less than two years from the purchase date, Enerdrive will repair the unit or, at its option, replace it, free of charge. If the unit is repaired, new or reconditioned replacement parts may be used, at manufacturer’s option.

This manual is also suitable for:

Epower industrial epi-3620Epower industrial epi-4815Epower epi-2430Epower epi-3620Epower epi-4815

Table of Contents