Process Parameters Menu; Process; Material; Diameter - Cebora EVO SPEED STAR 380 TS Manual

7.1 "PROCESS PARAMETERS" MENU.
Submenu "Process Parameters" is accessed through the"
Main Menu" or directly by means of key T7 (PAR). Here
are listed all the parameters that the operator may modify
according to the selected welding process (leds L10, L11,
L12).
In the "Process Parameters" you may save directly by
pressing key T6 (MEM)(see par. 7.2.1).

7.1.1 "Process".

yellow band but you also scroll all available processes.
The welding that can be selected are:
MIG Pulse synergic MIG/MAG welding (upon re-
quest art. 231).
MIG Synergic MIG/MAG welding.
MIG HD High deposit synergic MIG/MAG welding.
MIG Root Synergic MIG/MAG welding for drooping ver-
tical welding
MIG Man Traditional MIG/MAG welding.
TIG Welding process with non-meltable electrode
suited for all types of metals; aluminium, mag-
nesium and brass excluded. The arc strikes
by contact without high frequency.
MMA Welding process with coated, meltable elec-
trode.
7.1.2 "Material" (only in synergic MIG/MAG processes).
With this item you select the type of welding wire mate-
rial.
7.1.3 "Diameter" (only in synergic MIG/MAG processes).
The welding wire diameters are related to the selected

material.

7.1.4 "Gas" (in MIG/MAG processes).
Gas types that can be used are related to the selected
material.
7.1.5 "Arc Length Corr" -Arc length correction.
(Available in synergic MIG/MAG, MIG Root).
Arc length corr.
WARNING:
the adjusting page, which is similar for all parameters with
28
he fi rst parameter is the
welding process.
pressing key T12 you
enter the Process Selec-
tion page.
By means of keys T10
and T11, you select the
item highlighted by the
It allows to correct the
Volt Arc length by
means of keys T10 and
T11 or knobM2.
MIN MAX DEF.
-9.9V 9.9V 0.0V
an adjusting range , shows:
- The parameter name being corrected.
- The value and the unit.
- The adjusting range.
- The abbreviations:
MIN = minimum adjustment.
MAX = maximum adjustment.
DEF = preset value.
7.1.6 "Inductance Corr" - Impedance value correction.
(available in all MIG/MAG synergic welding pro-
cesses, MIG HD excepted)
By Allows correction of the impedance value.
Impedance value corr
7.1.7 "Start Mode" -selecting the welding start mode.
2T (active in MIG/MAG and TIG processes).
The machine begins welding when the torch trigger is
pressed, and stops when released.
4T (active in MIG/MAG and TIG processes).
To begin welding press and release the torch trigger;
to stop welding press and release it again.
3L (active in synergic MIG/MAG processes).
Welding starts when the torch trigger is pressed; the
welding current set by means of "Start current" will
be used. This current will be kept as long as the torch
trigger is held down; when it is released the current
returns to the preset value in the time set as "Slope
time" and it is kept until the torch trigger is pressed
again. When the torch trigger is pressed again, the
welding current will connect to the third current ("Cra-
ter- fi ller c rrent-") set with parameter "Crater Cur-
rent" according to the time set by "Slope time" and
it will be maintained until the torch trigger is released.
When the torch trigger is released welding stops.
3L adjustments
Start current
Slope time
Crater Current

7.1.8 "Spot".

(only in MIG/MAG 2T or 4T processes).
OFF (preset)
ON
The following adjustments are available when "ON" is se-
lected:
Spot time
Pause time
7.1.9 "HSA" "Automatic Hot Start".
(only in MIG/MAG synergic 2T or 4T processes).
This function is blocked when function 3L is activated and
works only with synergic processes.
Specially well suited for "hot" start when welding alumi-
num.
OFF (preset).
ON.
Key T5.
Key T7.
Key T6.
MIN MAX DEF.
-9.9 9.9 0.0
MIN MAX DEF.
10% 200% 135%
0.1 s 10 s 0.5 s
10% 200% 60%
MIN MAX DEF.
0.3 s 25 s 1.0 s
OFF 5 s OFF