Advertisement
7. TROUBLESHOOTING
SYMPTOM
Motor overheats / no power
Spindle bearing getting hot.
Unbalanced table travel.
Spindle shakes during use.
Vertical fine feed not functioning.
8. OPTIONAL ACCESSORIES
42 PIECE CLAMPING KIT
Part No. SM2502CK
MILL CHUCK SET (MT3)
CHUCK DIAMETERS
4,6,8,10,12,14,16MM
Part No. SM2502MCS
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
POSSIBLE CAUSE
Feed is too fast.
Faulty switch or motor.
Overload protection has operated.
No lubrication.
Spindle bearing too tight.
Excessive play in table movement.
Cut depth too deep for cutting tool.
Spindle bearing gap is too wide.
The chuck is loose.
Cutter is blunt.
Workpiece is loose.
Clutch is loose.
Worm and worm shaft are worn.
Hand wheel fixing is loose.
Drill feed still engaged.
QUICK VICE
(WIDTH 100MM)
Part No. SM2502QV
2 FLUTE HSS END MILL
(SINGLES AND SET)
SM2502EM04
SM2502EM06
SM2502EM08
SM2502EM10
SM2502EM12
SM2502EM14
SM2502EM16
SM2502EMSET
01284 703534
Original Language Version
CORRECTIVE ACTION
Decrease feed speed.
Replace faulty part. ( See parts list ).
Return speed switch to 'I' position and restart (See sec.4.10)
Apply grease.
Loosen the bearing.
Adjust the mitre strips. ( Refer to section 6.6 ).
Decrease the depth of the cut.
Reduce the gap or replace the bearing.
Re-seat the chuck in the arbor.
Sharpen or replace the cutter.
Secure the workpiece.
Tighten the clutch.
Replace worn parts. ( See parts list ).
Realign and tighten fixing.
Push drill feed hub inwards (See section 4.1)
INDEXABLE CARBIDE END MILL
(DIAM 4MM)
(DIAM 6MM)
(DIAM 8MM)
(DIAM 10MM)
(DIAM 12MM)
(DIAM 14MM)
(DIAM16MM)
(4 TO 16MM)
sales@sealey.co.uk
(MT3)
Part No. SM2502ICEM
COLLET (MT3)
(SINGLES AND SET)
SM2502C04
(DIAM 4MM)
SM2502C06
(DIAM 6MM)
SM2502C08
(DIAM 8MM)
SM2502C10
(DIAM 10MM)
SM2502C12
(DIAM 12MM)
SM2502C14
(DIAM 14MM)
SM2502C16
(DIAM16MM)
SM2502CSET
(4 TO 16MM)
www.sealey.co.uk
SM2502 Issue: 3(L) - 26/07/17
Advertisement
