1.2. General Safety; 2. Introduction & Specification; 3. Contents & Assembly - Sealey SM2502 Instructions Manual

1.2 GENERAL SAFETY
 WARNING! Disconnect the drilling/milling machine from the mains power, and ensure the cutting tool or chuck is at a complete standstill
before attempting to change accessories, service or perform any maintenance.
 Maintain the drilling/milling machine in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 Locate the drilling/milling machine in a suitable area. Ensure the surface is flat and firm. Keep area clean and tidy and free from unrelated
materials, and ensure there is adequate lighting.
 Keep the drilling/milling machine clean for best and safest performance and check moving parts alignment regularly.
 WARNING! Before each use check that drill/chuck/cutting tool is secure and that it is not worn or damaged. If worn or damaged replace
immediately.
 WARNING! Keep guard and holding fixings in place, tight and in good working order. Check regularly for damaged parts.
A guard, or any other part, that is damaged must be replaced with a new one, to ensure that it operates properly and performs its intended
function, before the tool is used. The safety guard is a mandatory fitting where drilling/milling machine is used in premises covered by the Health &
Safety at Work Act.
 Remove adjusting keys and wrenches from the machine and its vicinity before turning it on.
 WARNING! Wear approved safety eye protection and, if oil mist is generated, respiratory protection.
 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
 Keep hands and body clear of the work table when operating the drilling/milling machine.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Always clamp workpiece securely to the table or hold securely in a vice which is firmly mounted to the table. NEVER hold a workpiece by hand.
 Keep children and unauthorised persons away from the working area.
 WARNING! DO NOT switch the drilling/milling machine on whilst the drill or cutting tool is in contact with the workpiece. Bring the drill or
cutting tool gradually to the workpiece. Avoid un-intentional starting of the drilling/milling machine.
 DO NOT force the drilling/milling machine to achieve a task it was not designed to perform.
 DO NOT allow untrained persons to operate the drilling/milling machine.
 DO NOT get the drilling/milling machine wet or use in damp or wet locations or areas where there is condensation.
 WARNING! DO NOT use drilling/milling machine where there are flammable liquids, solids or gases such as petrol, paint solvents, waste
wiping rags etc.
 DO NOT operate the drilling/milling machine if any parts are missing or damaged as this may cause failure and/or possible personal injury.
 DO NOT remove the safety guard whilst in use.
 DO NOT attempt to remove a workpiece until the drill or cutting tool has stopped rotating.
 DO NOT touch the workpiece close to the cut as it will be very hot. Allow to cool.
 DO NOT leave the drill or cutting tool operating unattended.
 DO NOT operate the drill or cutting tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 When not in use switch the drilling/milling machine off and isolate from the power supply.
2. INTRODUCTION & SPECIFICATION
Bench mounting mini drilling/milling machine with the flexibility to handle most materials. Features include a 350W motor, variable speed drive,
working table with T-slots to enable clamping of workpieces and Metric graduated compound scales. The machine also incorporates a tilting
column which allows drilling/milling of workpiece at ±45° from vertical. Supplied with 13mm chuck accessory kit for adjusting and setting. An
optional stand is available, order Model No. SM3002ST. See below for a comprehensive range of accessories.
Specification:
Drilling capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm
Face Mill capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mm
End Mill capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16mm
Headstock travel (Z) . . . . . . . . . . . . . . . . . . . . . . . . . 180mm
Cross axis (X). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mm
Longitudinal axis (Y). . . . . . . . . . . . . . . . . . . . . . . . . 220mm
Spindle rotary angle . . . . . . . . . . . . . . . . . . . . . . -45° / +45°
Output power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350Watts
Spindle taper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MT3
3. CONTENTS & ASSEMBLY
Contents / accessories description:(fig.1)
Mini drilling/milling machine.

1.
Large wrench
2. Drill chuck and taper shank
3. Oil can
4.
Locking pin
5. 4 Hex keys (3,4,5,6mm)
6. Socket head wrench
7.
3 double ended spanners 8-10,14-17,17-19
8. Chuck key.
9. 2 Handles
10. 'T' nuts
11. Fuse
12. Draw bar
© Jack Sealey Limited
Spindle speed - Low range . . . . . 0 to 1100 rpm + or - 10%
Spindle speed - High range . . . . . 0 to 2500 rpm + or - 10%
T - slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12mm
Weight (Net/gross) . . . . . . . . . . . . . . . . . . . . . . . . . . 50/68kg
Packing size . . . . . . . . . . . . . . . . . . . . . 560 x 500 x 740mm
Original Language Version
fig. 1
SM2502 Issue: 3(L) - 26/07/17