Download Print this page
Sealey SMS2003 Instructions

Sealey SMS2003 Instructions

Saw blade sharpener - bench mounting 110w

Advertisement

Quick Links

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. safety
1.1.

electrical safety

warning! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely Portable
Appliance Tested. (PAT)
electrical safety information, it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
do not pull or carry the appliance by the power cable.
8
do not pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
do not connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.

general safety

warning! disconnect the saw blade sharpener from the mains power, and ensure that the cutting disc is at a complete standstill
before attempting to service or perform any maintenance.
maintain the saw blade sharpener in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Locate the saw blade sharpener in a suitable work area. Bolt securely to the workbench through the four holes on the base. Ensure
9
that the surface is flat and capable of supporting the weight of the sharpener (see fig.1). Keep the area clean and tidy and free from
unrelated materials, and ensure that there is adequate lighting.
Keep the saw blade sharpener clean for best and safest performance and check moving parts alignment regularly.
9
warning! Before each use check that the grinding stone is secure and that it is not worn or damaged. Test the grinding stone by
running it for a minute prior to its use. note: only competant persons should attempt to change grinding stones.
ensure that replacement stones are not damaged in any way - cracks or deformations etc. Also check the mounting flanges to check tha
9
they are not deformed, burred or chipped. do not over tighten a stone and never tamper with a stone in order to adapt it to a different
size holder.
warning! never operate the sharpener without the grinding wheel cover in place.
ensure that replacement grinding wheels meet the speed rating of the tool.
9
warning! This machine is designed to sharpen saw blades. do not attempt to sharpen any other tools and do not attempt to
grind any other objects.
warning! Wear approved safety eye protection, ear defenders and gloves.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
© Jack Sealey limited
saw blade sharpener - bench mounting
110w
model no:
Wear protective
Wear ear
gloves
protection
Original Language Version
sms2003
Wear a mask
Recommended fuse rating
5 Amp
SMS2003 | Issue 3 HF 07/03/18

Advertisement

loading

Summary of Contents for Sealey SMS2003

  • Page 1: Electrical Safety

    IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 The surface which is to be ground must be parallel to the corresponding side of the grinding stone. (See figs 3 & 4). Original Language Version SMS2003 | Issue 3 HF 07/03/18 © Jack Sealey limited...
  • Page 3 In case of set teeth, only grind every second tooth and then reverse the angle to grind the remaining teeth. 4.11.4. When grinding the tooth back make sure the grinding stone and saw blade are orientated as shown in fig.3. Original Language Version SMS2003 | Issue 3 HF 07/03/18 © Jack Sealey limited...
  • Page 4 Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey group, Kempson way, suffolk business park, bury st edmunds, suffolk. ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...