FingerTec AdapTec-X Installer's Manual page 7

deTAiLs oF wiring
AdapTec-X supports  types of installations, Convenient or Secure. You can select between
modes by applying different wiring arrangements during installation. Under Convenient
mode, AdapTec-X will unlock doors immediately after receiving responses from FingerTec
devices. This feature is supported by all FingerTec models.
For installations using Secure mode, there will be a 1s time delay when unlocking the door
after verification at FingerTec devices. This delay is due to the 6-bit Wiegand transmission of
encrypted password from device to AdapTec-X. This is an optional security feature provided
by AdapTec-X for users who favor more security (slight delay) over convenience (no delays).
AdapTec-X works with FingerTec terminals via an encrypted Wiegand signal to control the
WelcomeCheck-In
01-01 09:00 Sun
door open-close mechanism. Please make sure you are using the following FingerTec models
that support the encrypted 6-bit Wiegand signal to work with the AdapTec-X to setup a
door lock system:
Q2i
suppor t@finger tec.com
suppor t@finger tec.com
Qi
12-01-01 SUN
suppor t@finger tec.com
1
Step
Look for the power input port on
the FingerTec terminal. Normally the con-
nection ports on the terminals are marked as
PWR/+1V (red wire) and GND (black wire).
2
Step
Convenient Installation: Look for the door
lock output port NO and GND from the
terminal.Secure Installation: Look for the
Wiegand output port, WDO (green), WD1
(white) and GND (black) from the terminal.
3
Step
Connect the wires from the terminals to
AdapTec Plus.
w
1 2 3
ESC
4 5 6
7 8 9
0
MENU OK
R2
WelcomeCheck-In
Sun
01-01 09:00
WelcomeCheck-In
Sun
01-01 09:00
Q2i
suppor t@finger tec.com
suppor t@finger tec.com
AC900
Q2i
suppor t@finger tec.com
suppor t@finger tec.com
H2i
suppor t@finger tec.com
Hi Face ID 
12-01-01 SUN
12-01-01 SUN
suppor t@finger tec.com
suppor t@finger tec.com
Q2i
suppor t@finger tec.com
w
w
WelcomeCheck-In
Sun
01-01 09:00
1 2 3
ESC
4 5 6
1
2
7 8 9
12-01-01 SUN
4 5
0 OK
MENU
7 8
w 0
1
2 3 ESC
4 5 6
7 8 9
R2
0 OK
MENU
Q2i
suppor t@finger tec.com
suppor t@finger tec.com
suppor t@finger tec.com
R Kadex m-Kadex
R2
Face ID  i-Kiosk 100 Plus
Convenient Installation: See diagram 1, page 8 for
12-01-01 SUN
details. Secure Installation: See diagram 2, page 8 for
details.
H2i
4
Step
Connect the wires from AdapTec-X
suppor t@finger tec.com
suppor t@finger tec.com
suppor t@finger tec.com
to the door lock system.
H2i
for details). (Ignore this if you only want to use the sys-
suppor t@finger tec.com
tem for time attendance purposes)
5
Step
Connect AdapTec-X to a 1VDC
rechargeable backup battery.
page 8 for details). (This is optional. Ignore this if you
do not need any backup power).
6
Step Connect AdapTec-X to a power
source (1VDC A).
w
WelcomeCheck-In
Sun
01-01 09:00
1 2 3
ESC
4
5 6
7
8 9
0 OK
MENU
R2
suppor t@finger tec.com
3 ESC
6
9
MENU OK
R2
H2i
suppor t@finger tec.com
H2i
(See diagram 1, page 8
(See diagram 1,