AddSecure Iris Touch 2 Series Quick Installation & Maintenance Manual

Advertisement

IRIS Touch
Quick Installation &
Maintenance Guide
Version 1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Iris Touch 2 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for AddSecure Iris Touch 2 Series

  • Page 1 IRIS Touch Quick Installation & Maintenance Guide Version 1.0...
  • Page 2 Page 2 of 16 IRIS Touch Quick Installation & Maintenance Guide Version 1.0...
  • Page 3: Table Of Contents

    Contents Introduction ..........................4 Product Features ........................4 Package Contents ........................4 Board Configuration ........................ 5 Before You Start ........................6 Installing the IRIS Touch ......................7 6.1. Mounting ........................7 6.2. Power .......................... 7 6.3. Connections......................... 7 6.4. GSM SIM card (IRIS Touch 200 & 240) ................. 8 6.5.
  • Page 4: Introduction

    1. Introduction The IRIS Touch offers cost effective Alarm over IP (AoIP) for the commercial and residential sectors. All IRIS Touch diallers are certified as suitable for all Grade 4 systems with an Alarm Transmission System (ATS) configuration SP6 for single path, or ATS configuration DP4 for dual path (IRIS Touch 240 only).
  • Page 5: Board Configuration

    4. Board Configuration IRIS Touch RS232 SYS LED (TTL) Touch Screen Front tamper Dial capture port screw terminals RS232 RS485 Relays Pin inputs DC Power Micro SIM Card Ethernet Antenna SYS LED LED Colour Indication Not currently configured or indicating that there are some Yellow flashing current faults outstanding.
  • Page 6: Before You Start

    5. Before You Start Monitoring Centre (ARC) Make sure that the monitoring centre to which the IRIS Touch device will send alarm signals is equipped with the appropriate IRIS Secure Apps receiving system. The following information should be obtained from the monitoring centre. Dialler account number Monitoring centre IP address Ethernet Connection Details...
  • Page 7: Installing The Iris Touch

    6. Installing the IRIS Touch Use the following procedure to install your IRIS Touch dialler: 6.1. Mounting Choose a suitable location, taking into consideration the routing of cables: power, panel dialler interface cable. Remove the two case fixing screws under the slide cover and open the unit, remove the two PCB fixing screws and remove the PCB.
  • Page 8: Gsm Sim Card (Iris Touch 200 & 240)

    6.4. GSM SIM card (IRIS Touch 200 & 240) DO NOT FIT the SIM card until after you have performed the GPRS Network Scan detailed in the Section 6.8 “Configuration” you will be prompted when to insert the SIM card. 6.5.
  • Page 9: Configuration

    6.8. Configuration To configure your dialler, use one of the following methods:  Touch screen.  Alarm panel integration e.g. Honeywell Galaxy (RS485 connection). Note: For connections to Honeywell Galaxy on the serial integration ensure you configure the alarm panel first as this will transmit configuration to the IRIS Touch dialler. For more details on the alarm panel integration download the full panel installation manual from http://www.chironsc.com/downloads_security.html.
  • Page 10: Panel Configuration

    Once you have the required GPRS signal strength power down the dialler and insert the SIM card into the SIM card holder, then power the dialler back up. Go back into the ‘Installers Menu’ and enter in the installer code that you had setup beforehand and then select the Installation Wizard as indicated next.
  • Page 11: Maintenance

    7. Maintenance There is no requirement for any onsite maintenance on the IRIS Touch If you want to carry out a maintenance inspection please perform the following:  Confirm the status of the IRIS Touch unit.  Clear any faults on the dialler. ...
  • Page 12: Communication Paths Checks

    7.3. Communication paths checks You can test the communication paths for both polling and alarm communications using the ‘Test’ option in the Main installer menu, this will test all configured communication paths. Please refer to the IRIS Touch Engineer Manual for more details available from http://www.chironsc.com/downloads_security.html.
  • Page 13: Specifications

    8. Specifications Transmission paths Ethernet Standard ̶ UTP 10/100 Base T with auto-negotiation Connection ̶ Rj45 socket for CAT5 cabling IP addressing ̶ Dynamic (DHCP) or fixed Connection fault detection ̶ Loss of Ethernet synchronisation Standard Quad band GSM Quad band GSM ̶...
  • Page 14 Safety Care should be taken when connecting telecommunications equipment to ensure only like interfaces are connected to avoid safety hazards. SELV: SELV (Safety Extra-Low Voltage) is defined as a secondary circuit which is so designed and protected that under normal and single fault conditions the voltage between any two accessible parts does not exceed a safe value (42.4V peak or 60V dc maximum) The interfaces on the IRIS Touch have the following safety classifications: ...
  • Page 15 IRIS Touch Quick Installation & Maintenance Guide Version 1.0 Page 15 of 16...
  • Page 16 The future of security, secured IP by security professionals, for the professional security industry Installation and Service Engineer Support Telephone: +44 971 977 1133 (Calls are charged at 10p a minute from a BT landline. Calls from mobiles or other providers may be higher) Sales Enquiries: +41 435 080 870 Email: sales@chironsc.com www.chironsc.com...

This manual is also suitable for:

Iris touch 200Iris touch 220Iris touch 240

Table of Contents