AddSecure IRIS-4 160 Quick Installation And Maintenance Manual

AddSecure IRIS-4 160 Quick Installation And Maintenance Manual

Hide thumbs Also See for IRIS-4 160:

Advertisement

AIRBORNE
IRIS-4 160
DC MEDIUM
Quick Installation and
Hurtigmanual/
Maintenance Guide
Snabbguide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IRIS-4 160 and is the answer not in the manual?

Questions and answers

Summary of Contents for AddSecure IRIS-4 160

  • Page 1 AIRBORNE IRIS-4 160 DC MEDIUM Quick Installation and Hurtigmanual/ Maintenance Guide Snabbguide...
  • Page 2: Table Of Contents

    IRIS-4 160 1. IntRoDuCtIon IRIS-4 160 The IRIS-4 160 offers a new concept in Alarm over backup for mains over 15 hours support in the case Quick Installation and IP (AoIP) providing cost effective AoIP for the of mains power source failure . This backup is pro- Maintenance Guide residential sector .
  • Page 3: Package Contents

    4g/3g/2g SIM Card and access Point name ⑭ = SIM card holder If the installation uses 4G/3G/2G then a SIM card will be required . The IRIS-4 160 will also need to be given ⑮ = 4G/3G/2G antenna a 4G/3G/2G ‘Access Point Name’ (APN) and other possible configurations as shown below . Obtain these from ⑯...
  • Page 4: Installing The Iris-4 160 Dialler

    PCB (retained by in length. PCB chip antenna . The IRIS-4 160 requires 4 x 1 . 5 V NiMh AA size two clips to left and right off the board) . Position the • 4G/3G/2G enabled systems: 4G/3G/2G antenna rechargeable batteries (not included) .
  • Page 5: 4G/3G/2G Sim Card

    Premier on the serial integration, as these will tions made should be as shown below . The IRIS-4 160 dialler has four pin inputs that can be transmit configuration to the IRIS-4 160 dialler. used to generate messages, These can be:...
  • Page 6 Connecting to this should turn the SYS LED solid ‘purple’ and using the web browser connect to the Android and Window phones. IRIS-4 160 web interface by browsing to ‘iris . l ocal’ . Android operating system and Microsoft Windows phones will require the IRIS Connect App .
  • Page 7 If the signal strength is below or close to minimum range, requests operator name and records the signal then try to reposition the IRIS-4 160 or use an exter- strength . This will take a few minutes to complete .
  • Page 8: Panel Configuration

    IRIS-4 160 web interface by browsing to ‘iris . l ocal’ . there is no need to change any settings on the reported .
  • Page 9: Confirm Current Status

    Monitoring Centre that all is working correctly . IRIS-4 160 before it may be necessary to download/ “Trouble report” menu . Please refer to the IRIS-4 160 install some application software to connect via Engineering Manual for more details available from On first entry to the reflash option, which could be the Wi-Fi Web browser, please refer to Section 6.9...
  • Page 10: Specifications

    IRIS-4 160 transmission paths IRIS-4 160 IRIS-4 160 Alarm transmission PIN Inputs interface to alarm panel Maximum input voltage range 0V to +24V Note: Quick Installation and Input ‘low’ (alarm) threshold < 1V Cabling must not Maintenance Guide Input ‘high’ (restore) threshold > 2V exceed 3 meters Internal pull-up impedance 10K to 3 .
  • Page 11 Laddkort • Plastkabinett, sabotasjesikret. • Plastkapsling, sabotagesäker. Mål (BxHxD): 170x160x60 mm Mått (BxHxD): 170x160x60 mm The interfaces on the IRIS-4 160 have the following safety classifications: • 1stk. NiMH 2200 mAh batteri • 1st. NiMH 2200 mAh batteri • Dial capture interface: SELV suitable for connection to the TNV interface of single line telecommunications equipment such as telephones, alarm panels, etc .

Table of Contents