Drilling Of Holes For Midi Sockets; Midi Sockets Mounting - CHD Elektroservis SY2-KBD Installation Manual

SY2 SY2- - - - KBD SY2 SY2 KBD KBD KBD
c) All instrument's parts and boards needed for the interface installation are now accessible (fig. 2.1.3).
2.2 2.2

DRILLING OF HOLES FOR MIDI SOCKETS

DRILLING OF HOLES FOR MIDI SOCKETS
2.2 2.2 DRILLING OF HOLES FOR MIDI SOCKETS DRILLING OF HOLES FOR MIDI SOCKETS
The interface has both MIDI input and output. Only MIDI input is necessary for the basic interface operation.
MIDI output has not to be installed – see chapter 3.1. Nevertheless, having both MIDI input and output (MIDI-IN
and MIDI-THRU/OUT sockets) is more convenient for an easy integration in a more advanced MIDI system.
a) The suitable place for the MIDI sockets montage is on the right side of the metal panel on rear side of the
instrument (fig. 2.2.1). You have to drill six holes to the panel.
b) Drill two holes with diameter 16 mm and four holes with diameter 3,2 mm to the metal panel as shown on
fig. 2.2.2 (all dimensions are in mm). Use sharp drills and work carefully
other parts and cables inside the instrument are not damaged
Figure 2.2.1 Figure 2.2.1
Figure 2.2.1 Figure 2.2.1
c) Clean the edge of the holes with small rasp or tip of bigger drill from both sides of the panel after the holes
are drilled.
c) Clean all iron sawdust and raspings from the inside of the instrument Clean all iron sawdust and raspings from the inside of the instrument, they can cause short circuits or serious
Clean all iron sawdust and raspings from the inside of the instrument Clean all iron sawdust and raspings from the inside of the instrument
electrical damage if left inside the instrument. Please clean the instrument carefully!
2.3 2.3

MIDI SOCKETS MOUNTING

MIDI SOCKETS MOUNTING
2.3 2.3 MIDI SOCKETS MOUNTING MIDI SOCKETS MOUNTING
a) Pull flat connectors of MIDI cables (from the interface accessory) through 16 mm holes in the metal panel
from outer side and insert DIN sockets into the holes. Both MIDI cables are identical and can be swapped.
Figure 2.3.1 Figure 2.3.1
Figure 2.3.1 Figure 2.3.1
1
If you want to be sure that the instrument parts will not be damaged during the drilling, you can remove the switch and the connectors from the
panel and then you can remove the whole metal panel from the instrument. Now, it is allowed to drill the panel outside the instrument. After all
holes are drilled and cleaned, the panel can be placed back to the instrument.
No part of this publication may be reproduced in any form without the written permission of CHD Elektroservis.
Installation Manual Installation Manual
Installation Manual Installation Manual
Copyright © 2019 CHD Elektroservis. All rights reserved.
work carefully so that the cover is not scratched and
work carefully work carefully
1 1 1 1
are not damaged !
are not damaged are not damaged
5 5 5 5
Yamaha SY- - - - 2 (SY Yamaha SY 2 (SY- - - - 1) MIDI Interface 1) MIDI Interface
Yamaha SY Yamaha SY 2 (SY 2 (SY 1) MIDI Interface 1) MIDI Interface
Model 8- - - - 439 / v. 1.00 Model 8 Model 8 Model 8
Figure 2.2.2 Figure 2.2.2
Figure 2.2.2 Figure 2.2.2
Figure 2.3.2 Figure 2.3.2
Figure 2.3.2 Figure 2.3.2
439 / v. 1.00 439 / v. 1.00 439 / v. 1.00