Interface Adjustment - CHD Elektroservis SY2-KBD Installation Manual

SY2- - - - KBD SY2 SY2 SY2 KBD KBD KBD
Figure 2.8.4 Figure 2.8.4
Figure 2.8.4 Figure 2.8.4
2.9 2.9

INTERFACE ADJUSTMENT

INTERFACE ADJUSTMENT
2.9 2.9 INTERFACE ADJUSTMENT INTERFACE ADJUSTMENT
There are two variable resistors on the interface board
labeled "OFFSET" and "RANGE" (fig. 2.9.1). They must be
adjusted before the interface is used. Adjustment
procedure is following
a) Connect MIDI output of your MIDI master keyboard (or
PC / sequencer / DAW) to MIDI input of the interface
b) Connect audio output of the instrument to a tuner or
to a frequency meter.
c) Set all controllers on the instrument's panels to a clear
sound without any modulation.
Rear panel:
• OUTPUT
OUTPUT switch to HIGH
OUTPUT OUTPUT
Top panel:
• PITCH
PITCH PITCH PITCH- - - - BEND BEND and PORT BEND BEND PORTAMENTO PORT PORT
• Tone selector switches
• Tone side selector
• TRANSPOSITION
TRANSPOSITION selector
TRANSPOSITION TRANSPOSITION
• TOUC
TOUCH CONTROL H CONTROL switches
TOUC TOUC H CONTROL H CONTROL
• FOOT CONTROL
FOOT CONTROL switches
FOOT CONTROL FOOT CONTROL
• VOLUME
VOLUME VOLUME VOLUME knob to middle position
Left panel:
• TUNE
TUNE knob to middle position
TUNE TUNE
• PULSE WIDTH
PULSE WIDTH knob
PULSE WIDTH PULSE WIDTH
• VIBRATO
VIBRATO - - - - DEPTH VIBRATO VIBRATO DEPTH knob DEPTH DEPTH
• ENVELOPE
ENVELOPE sliders
ENVELOPE ENVELOPE
• FILTER
FILTER sliders FILTER FILTER LOW PASS FREQUENCY LOW PASS FREQUENCY LOW PASS FREQUENCY LOW PASS FREQUENCY to HIGH
position) / LOW PASS LOW PASS RESONANCE
LOW PASS LOW PASS
2
It is suppossed that the interface is in "Factory Reset" status before the adjustment procedure. If it is not, send the F0 00 20 21 7F 52 50 03 7F 5C
F7 [hex] SysEx message to the intarface first. F7 [hex]
F7 [hex] F7 [hex]
3
Set transmitting MIDI Channel to number 1 on the master keyboard.
No part of this publication may be reproduced in any form without the written permission of CHD Elektroservis.
Installation Manual Installation Manual
Installation Manual Installation Manual
2 2 2 2
:
HIGH (left position)
HIGH HIGH
AMENTO AMENTO switches AMENTO
FLUTE / CLARINET FLUTE CLARINET tone on
FLUTE FLUTE CLARINET CLARINET
to SIDE I SIDE I (upper position)
SIDE I SIDE I
NORMAL switch on NORMAL
NORMAL NORMAL
all switches off
both switches off
maximum (fully clockwise) maximum
maximum maximum
minimum (fully counterclockwise) minimum minimum minimum
ATTACK, DECAY ATTACK DECAY, RELEASE RELEASE to SHORT
ATTACK ATTACK DECAY DECAY RELEASE RELEASE
RESONANCE and HIGH PASS RESONANCE HIGH PASS RESONANCE to MIN
RESONANCE RESONANCE HIGH PASS RESONANCE HIGH PASS RESONANCE
Copyright © 2019 CHD Elektroservis. All rights reserved.
3 3 3 3
.
both off off off off (upper position)
on (lower position), all others off
on on
on (lower position)
on on
off (upper position)
off off
off (upper position)
off off
SHORT (lower position) / SUSTAIN
SHORT SHORT
HIGH HIGH (upper position) / HIGH PASS FREQUENCY HIGH
11 11 11 11
Yamaha SY- - - - 2 (SY Yamaha SY 2 (SY- - - - 1) MIDI Interface 1) MIDI Interface
Yamaha SY Yamaha SY 2 (SY 2 (SY 1) MIDI Interface 1) MIDI Interface
Model 8 Model 8- - - - 439 / v. 1.00 Model 8 Model 8
Figure 2.8.5 Figure 2.8.5
Figure 2.8.5 Figure 2.8.5
Figure 2.9.1 Figure 2.9.1
Figure 2.9.1 Figure 2.9.1
off (upper position)
off off
SUSTAIN to MAX MAX (upper position)
SUSTAIN SUSTAIN MAX MAX
HIGH PASS FREQUENCY HIGH PASS FREQUENCY to LOW HIGH PASS FREQUENCY
MIN (lower position)
MIN MIN
F0 00 20 21 7F 52 50 03 7F 5C
F0 00 20 21 7F 52 50 03 7F 5C F0 00 20 21 7F 52 50 03 7F 5C
439 / v. 1.00 439 / v. 1.00 439 / v. 1.00
LOW (lower LOW LOW