Related Manuals for TOPMAQ WWBA1650 Series
Summary of Contents for TOPMAQ WWBA1650 Series
- Page 1 Operator’s Manual Band Saw CAUTION : Read and follow all Safety Rules and Operating Instructions before First Use of this Product. Keep this manual with tools. 1612-MJ9-B/J...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Product Specifications ......................3 Safety ............................3 Accessories and Attachments ....................6 Carton Contents ........................6 Installation ..........................8 Adjusting...........................10 Operation ..........................13 Maintenance..........................15 Assembly Diagram……......................16... -
Page 3: Product Specifications
PRODUCT SPECIFICATIONS Attention: Please choose proper power source, voltage and frequency that are shown in the label for your band saw. BAND SAW Motor Power 300W 228mm Throat Width Cutting Capacity 90mm 50Hz 635 m/min Cutting Speed 750 m/min 60Hz Blade Size 1575 mm(Length) X 3-10mm(Width) Table size... - Page 4 If devices are provided for the connection for dust extraction and collection facilities ensure these are connected and properly used. 11. Do not abuse the cord. Never carry the tool by the cord of yank it to disconnect it from the socket, Keep the cord away from heat, oil and sharp edges.
- Page 5 Select the correct saw blade for the material to be cut. Do not use saw blades manufactured from high speed steel. To reduce the emitted noise, always be sure that the blade is sharp and clean. 10. Do not cut metals such as nails and screws. Inspect for and remove all nails, screws and other foreign matter form the workpiece before operation.
-
Page 6: Accessories And Attachments
WARNING: Improper connection of equipment grounding conductor can result in the risk of electrical shock. equipment should be grounded while in use to protect operator from electrical shock. -Check with a qualified electrician if you do not understand grounding instructions or if you are in doubt as to whether the tool is properly grounded. - Page 7 TABLE OF LOOSE PARTS Unpack carton; check you machine to see parts listed below: Band saw Fence Table assembly Miter gauge 8-10mm wrench Hex wrench (4mm, 6mm) 2pcs Lifting handle Hook with nut (△) Push stick (△) 10. Feet (not shown) (△) Alternative assembly parts .
-
Page 8: Installation
INSTALLATION Attach the foot to band saw For the model with dust drawer Put down the machine on a timber according to the fig. Attach foot A & B to band saw by using pan head screw and washer. ... - Page 9 3. Mounting table assembly Remove the D-nut, washers, and wing screw on the saw table. Slide the saw table past the blade and through the slot moving to the frame, pulling the angle adjustment knob away from the saw frame, Align the teeth on the saw table bracket into the teeth on the angle adjustment knob. Release the knob.
-
Page 10: Adjusting
Fix the band saw to a workbench by using four thread forming screws (not provide). Place the fence and miter gauge onto the table. Fence Miter gauge Thread forming screw Thread forming screw ADJUSTING WARNING: Always be sure that the tool is switched off and unplugged before any adjustments. Tilting table ... - Page 11 After adjusting, retighten the tracking lock knob and close the cover. Upper cover Tracking set knob Lower cover Adjusting the blade tension Warning: Too much tension can cause the band saw blade to break. Too little tension can cause the driven band saw wheel to slip and the saw blade to stop.
- Page 12 Locking knob Adjusting knob Guide bearing Saw blade Align the lower blade guide The lower blade guide needs to be readjusted after every band saw blade change or tracking adjustment. Through the hole (B) and (E), use hex wrench to loosen socket bolts, adjust guide block (D) and thrust bearing (C) just like adjusting upper blade guide.
-
Page 13: Operation
Changing the band saw blade. Warning: Saw blade is dangerous. Be sure to wear gloves when handing saw blade in situations such as removing from packaging, mounting or replacing blade. Remove the D-nut, washers, and wing screw on the saw table. D-nut ... - Page 14 When cutting round stock, firmly secure it. Before starting work, check saw blade, upper and lower blade guard are in proper working order. Replace damaged parts immediately Assume correct work position (the band saw blade’s teeth must point towards the operator). ...
-
Page 15: Maintenance
Connecting to dust collector The band saw provides a dust port. It should be connected with dust collector when sawing wood. Dust port For the model with dust drawer If you do not have dedicated band saw extraction, there is another chance to get rid of the saw dust. Most of debris except usual dust drifts would fall through a grating into the dust drawer. -
Page 16: Assembly Diagram
Assembly Diagram △Alternative assembly parts . Your machine may not have this assembly part.
Need help?
Do you have a question about the WWBA1650 Series and is the answer not in the manual?
Questions and answers