Roger Technology H70/104AC Instruction And Warnings For The Installer
Hide thumbs
Also See for H70/104AC:
- Instructions and warnings for installation (260 pages) ,
- Instruction and warnings for the installer (236 pages) ,
- Instructions and warnings (232 pages)
Advertisement
Quick Links
|
IS83 Rev.03
20/05/2015
ROGER CENTRALI DI CONTROLLO
centrale per 1 motore 230Vac
H70/104AC - H70/105AC
IT -
Istruzioni e avvertenze per l'installatore
- pag.2
EN -
Instruction and warnings for the installer
- pag.22
DE -
Anleitungen und Hinweise für den Installateur
- S.42
ES -
Instrucciones y advertencias para el instalador
- pag.63
FR -
- page 84
PT -
Instruções e advertências para o instalador
- pág.105
automazioni evolute
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Roger Technology H70/104AC
Summary of Contents for Roger Technology H70/104AC
- Page 1 IS83 Rev.03 20/05/2015 ROGER CENTRALI DI CONTROLLO centrale per 1 motore 230Vac H70/104AC - H70/105AC IT - Istruzioni e avvertenze per l’installatore - pag.2 EN - Instruction and warnings for the installer - pag.22 DE - Anleitungen und Hinweise für den Installateur - S.42...
- Page 2 6.2.1 6.2.2 6.2.3 TEST mode PHOTOCELL TEST mode Maintenance Disposal H70/104AC H70/105AC This manual is only intended for personnel considered of interest to the end user. This manual refers to controls panels H70/104AC single-phase asynchronous 230Vac motor. SHOCK HAZARD WARNINGS...
- Page 3 230Vac ± 10% 50Hz 1300W CONNECTABLE MOTORS 230Vac RATED POWER MOTOR 600W GATE OPEN LIGHT POWER OPERATING TEMPERATURE DEGREE OF PROTECTION IP00 PRODUCT DIMENSIONS Figure 1 outputs COS2 Figures 2 and 3 COS1 Earth 27,28 COM 9,10 LAM H70/104AC o 24Vac H70/105AC H70/104AC...
-
Page 4: Important Notes
H70/105AC motor +5Vdc the motor 24Vac Do not connect Inputs FC1 and FC2 IMPORTANT NOTES mode Inputs FT1 and FT2 standard. parameter FT1 ignored during opening FC1 -> FCA FC2 -> FCC FC1 -> FCC FC2 -> FCA For H70/104AC... - Page 5 IF THE PHOTOCELLS 1 IS NOT INSTALLED IF THE PHOTOCELLS 2 IS NOT INSTALLED Inputs COS1 and COS2 standard. STATUS CONTROLS STATUS SAFETY PROTECTIONS Radio receiver plug-in COS1 COS2 POWER STOP ALWAYS ON SAFETY PROTECTIONS DISABLED BY PARAMETER COMMANDS AND SAFETY PROTECTIONS STATUS MODE: NO SAFETY PROTECTIONS appears...
-
Page 6: Standard Parameter
6.2.1 Changing a parameter 6.2.2 Restoring standard factory parameters entered the password to protect your data. NOTE: Changing the numerical value of the STANDARD VALUE ON PARAMETER FUNCTION DESCRIPTION DISPLAY AND VALUE “generator” mode generators open stop close stop open stop close ... open close open close open close stop open Torque during slowdown... - Page 7 6.2.3 TEST mode safety protection terminal WARNING! block number in a state of until the safety protection Name of the active input goes back to resting) SIMPLIFIED MODE (displayed for 5 seconds) highest Sb = unlock priority 18 = ST 17 = COS1 16 = COS2 15 = FT1...
- Page 8 down as set in parameter Press PROG (o PP): stops without encoder and with safety edge WARNING! and closing. must Programming is interrupted (with error message Press PROG (or PP): starts to open starts WARNING!
- Page 9 without encoder and without safety edge WARNING!! First press PROG (o PP): Second press PROG (o PP) Third press PROG (o PP) programming is complete. PHOTOCELL TEST mode mode.
- Page 10 WARNING! Depending on the selected mode, standard voltage is restored.
- Page 11 PASSO-PASSO (PP) OPENS – CLOSES – STOPS – OPENS Man present Gate open light Length travelled in slowdown...
- Page 12 3 seconds 6 seconds. SECONDS SECONDS...
- Page 13 SECONDS DISABLED SECONDS Torque level during start-up...
- Page 14 Pressure surge DISABLED TIME IN SECONDS average slowdown...
- Page 15 parameter Mode if photocell FT1 is interrupted when opening Mode if photocell FT1 is interrupted when closing does not permit opening permits opening OPENS WHEN IT IS OBSCURED Mode if photocell FT2 is interrupted when opening Mode if photocell FT2 is interrupted when closing does not permit opening permits opening OPENS WHEN IT IS OBSCURED...
- Page 16 TENTHS OF A SECOND...
- Page 17 NOT PRESENT NOT PRESENT NOT PRESENT PEDESTRIAN OPEN CLOSE STOP...
- Page 18 Durata luce di cortesia ACTIVE DURING THE ENTIRE OPERATION SECONDS OF ILLUMINATION AFTER THE END OF THE OPERATION Restoring standard factory values Version HW Year of manufacture FW version . For...
- Page 19 Days the control unit is on Password Change password view parameter parameter Disposal connected. Maintenance Warning: consider replacing it.
Need help?
Do you have a question about the H70/104AC and is the answer not in the manual?
Questions and answers