Advertisement
6.1 Assembling the components
Some parts of the mower come disassembled. For
quick and easy assembly, read and follow the
instructions below.
Important! You will need the following additional
tools (not supplied) for assembly, and also for
maintenance work:
A 1 liter measuring jug (oil/petrol resistant)
A petrol can
neck)
Household wipes (to wipe up oil/petrol residue;
A petrol suction pump (plastic, available from
DIY stores)
An oil can with hand pump (available from DIY
stores)
Assembly
1.
to the mower housing and set the desired
working height. 3 different working heights
are available. Each peg on the lower push bar
can be inserted into a hole situated directly
opposite to it, on the mower housing, for
example A-A (Fig. 3). The lower push bar must
the cover (Fig. 3a/Item 23) and attach the push
bar (5) using the square head screws (15) and
the star screws (18) as shown in Figure 3a.
2.
Fasten the top push bar to the bottom push bar
using a screw (Fig. 3b/Item 16) and a star screw
(Fig. 3b/Item 18) on each side. Make sure that
the lobes of the screws are folded towards the
inside so that the high speed clamping function
remains operational.
3.
Insert the grip of the starter cord (Fig. 3c/Item
4) into the hook provided for that purpose as
shown in Figure 3c.
4.
Fasten the cords to the push bar with the
supplied cable ties (Fig. 3d/Item. 13).
5.
The debris bag should be assembled as shown
in Figure 3e. For this, insert the upper lugs of
the debris bag carefully into the openings on
the lower debris bag.
6.
hand and hook in the grass bag (Fig. 4/Item 7)
as shown in Figure 4
6.2
Setting the cutting height.
Important! Adjust the cutting height only when
the engine is switched off and the plug boot has
been pulled.
AFTER SALES SUPPORT
AFTER SALES SUPPORT
1300 922 271
service.australia@einhell.com
1300 922 271
service.australia@einhell.com
Before you begin to mow, check to ensure
that the blade is not blunt and that none of
the fasteners are damaged. T o prevent any
imbalance, replace blunt and/or damaged
blades as a set only (if applicable). T o carry out
the spark plug boot.
The cutting height is centrally adjusted with the
cutting height adjustor lever (Fig. 7/Item 9). Up
to 5 different cutting heights can be selected.
Pull the adjustor lever out and select the desired
cutting height. The lever snaps into the desired
position.
Operation
Important! The engine does not come with oil in it.
Add 590 ml of engine oil before starting the engine
the rst time. The engine cannot be started without
suf cient oil. Over lling the oil will destroy the engine.
Before starting the engine, ll in petrol as this is also
not supplied upon delivery.
Before you start mowing, you should run through
this operation several times in order to ensure that
the machine is working properly.
Whenever you need to perform any kind of
adjustment and/or repair work on your lawn mower,
wait until the blade has come to a complete stop.
Always switch off the engine before carrying out any
adjustments, maintenance or repairs.
In order to avoid any unintentional start-ups of the
lawn mower, it comes equipped with an engine
brake (Fig.1/ Item 1).
7.1 Operating the Lawn Mower
1.
Before starting the engine, check the oil level on
the dip stick by opening the oil ller cap
(Fig. 1/ Item 11) and top up if required.
2.
Fill the tank with petrol when it is empty, using
funnel and measuring vessel. Make sure that the
petrol is clean. Note: Use only unleaded petrol
as fuel. Warning: Never use more than one safety
petrol can. Do not smoke when refuelling. Switch
off the engine before refuelling and allow the
engine to cool down for a few minutes.
3.
Important! Before you start the engine, move the
Engine Start/ Stop lever (Fig. 5b/ Item 1) several
times to be sure that the stop cable is properly
working. To start the engine, pull the throttle lever
(Fig. 6/ Item 3) all the way to the 'Choke setting'
(Fig. 6). Push the primer (Fig. 1/Item 12) three times.
Pull the Engine Start/ Stop lever (Fig. 5b/Item 1) in
the 'Engine START' position as shown in Fig. 5b.
Make sure the drive lever (Fig. 5b / Item 19) is in
the 'Drive OFF' position as shown in Fig. 5b. Then
pull the starter cable (Fig. 1/ Item 4).
12
MODEL NUMBER: RG-PM 48 S B&S, 08/12
12
MODEL NUMBER: RG-PM 48 S B&S, 08/11
7
Hide quick links:
Advertisement
