Download Print this page
Aruba 9004-MNT-19 Installation Manual
Aruba 9004-MNT-19 Installation Manual

Aruba 9004-MNT-19 Installation Manual

Advertisement

Quick Links

This document provides installation instructions for mounting the 9004 gateway in a two-post
19-inch Telco rack. The rack mount tray supports installation of two 9004 gateway units.
Package Contents
Rack mount tray
Eight M3 x 5 mm flat head screws
Four M6 x 15 mm Phillips pan head screws
Four rubber clamps
Aruba 9004-MNT-19 Kit Installation Guide (this document, printed)
Rack Mount Installation
This mounting option allows mounting the 9004 gateway in a two-post 19-inch Telco rack.
Required Tools and Equipment
The following tools and equipment are required for installing a 9004 gateway:
Rack mount tray (x1) for rack mount installation
M3 x 5 mm flat head screws (x8) for securing the gateway on the rack mount tray
M6 x 15 mm Phillips pan head screws (x4) for rack mount
Suitable screwdrivers for all screw types provided in the box (not included in the kit)
Some racks require screws that differ from those included with the 9004 gateway accessory kit. Ensure that
you have the correct screws before installing the 9004 gateway.
Installation Steps
To install a 9004 gateway into a two post 19-inch rack:
1. Align the 9004 gateway to the screw hole provided on the rack mount tray.
Ensure that the front panel of the 9004 gateway is facing towards the front side of the rack mount tray.
2. Align the screws under the rack mount tray and tighten the screws to secure the 9004 gateway on
the rack mount tray. See
0512128-03
|
September 2019
Aruba 9004-MNT-19 Kit
Figure
1.
Installation Guide
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 9004-MNT-19 and is the answer not in the manual?

Questions and answers

Summary of Contents for Aruba 9004-MNT-19

  • Page 1 Four M6 x 15 mm Phillips pan head screws  Four rubber clamps  Aruba 9004-MNT-19 Kit Installation Guide (this document, printed)  Rack Mount Installation This mounting option allows mounting the 9004 gateway in a two-post 19-inch Telco rack.
  • Page 2 Figure 2 Attaching Rubber Clamp to the DC Power Adapter 5. Place the power adapter on the rack mount tray aligning it with the placement tabs provided. See Figure Figure 3 Power Adapter Mounting Aruba 9004-MNT-19 Kit | Installation Guide...
  • Page 3 7. Connect the DC power plug into the DC power connector provided on the back panel of the 9004 gateway. 8. Mount the rack mount tray within the two-post 19-inch rack using four M6 x 15 mm Phillips pan head screws and a suitable screwdriver. See Figure Aruba 9004-MNT-19 Kit | Installation Guide...
  • Page 4 Figure 6 Rack Mount Installation Rack mount installation of the 9004 gateway is now complete. Aruba 9004-MNT-19 Kit | Installation Guide...
  • Page 5: Contacting Support

    Security Incident Response Team (SIRT) Site: https://www.arubanetworks.com/support-services/security- bulletins/ Email: aruba-sirt@hpe.com © 2019 Aruba, a Hewlett Packard Enterprise company All rights reserved. www.arubanetworks.com Hewlett Packard Enterprise Company 3333 Scott Boulevard Santa Clara, California 95054 Phone: 408.227.4500 Fax: 408.227.4550 Aruba 9004-MNT-19 Kit | Installation Guide...