Related Manuals for Litepanels Gemini 2x1 Soft
Summary of Contents for Litepanels Gemini 2x1 Soft
- Page 1 Gemini Effects Guide Rev. C - November 2019 For use with: Gemini 2x1 Soft Firmware Rev B2 and later Gemini 1x1 Soft Firmware Rev A0 and later...
-
Page 2: Table Of Contents
Emergency! ..............................3 Fire ................................3 Fireworks ............................... 4 Hue Burst ..............................5 Lite-ning ................................ 6 Paparazzi ............................... 6 Party Lites ..............................7 Pulsing (Ramp Up/Ramp Down) ........................8 Squares (Sharp Pulses) ..........................9 Strobe ................................10 TV/Monitor ..............................11 litepanels.com... -
Page 3: Introduction
DMX Control Many parameters for individual effects can be adjusted or triggered via DMX, allowing remote operation and control. For details on specific channel assignments and values, consult the Gemini DMX Guide. litepanels.com... -
Page 4: Emergency
COLOR MIX: Larger intensities lower the HUE value RATE: Smaller values used for larger flames, larger values used for smaller flames. Ex. Candle RATE = 80 DEPTH: Smaller values used for smaller flames, larger values used for larger flames litepanels.com... -
Page 5: Fireworks
100 = Large number of bursts Random SUSTAIN TRIG Trigger the bursts Select the fade time of the bursts manually, regardless of PRESS SHORT = Burst decays quickly the FREQ setting MED = Burst decays moderately LONG = Burst decays slowly Notes: litepanels.com... -
Page 6: Hue Burst
LOOP MODE = Bursts repeat as determined by OFF TIME setting Notes: GAP formula for muzzle flashes: GAP= ((1/(RPMs/60)) - 0.036)x1000 Typical GAP settings for muzzle flashes: 833RPM = 36 GAP 700RPM = 50 GAP 600RPM = 64 GAP litepanels.com... -
Page 7: Lite-Ning
Select LOOP MODE or MANUAL change MODE PRESS 50ms = Short flash MANUAL MODE = Trigger a flash 100ms = Med flash manually LOOP MODE = Flashes are output 150ms = Long flash continuously BULB = Flash with decay Notes: litepanels.com... -
Page 8: Party Lites
Blend = Color is continuously changes output from the HUE color wheel COLORS TRIG Press to trigger a color Select colors used in the show while change in PULSING or CHASE modes Red/White/Blue PRESS Red/Green/Blue 6-Color 12-Color Random Notes: litepanels.com... -
Page 9: Pulsing (Ramp Up/Ramp Down)
2000 = Slow Ramp MODE TRIG Press to trigger the Select LOOP MODE or MANUAL pulses manually at any MODE. time MANUAL MODE= Trigger the PRESS Change Row Pulses manually only. LOOP MODE= Pulses repeat as determined by OFF T setting. Notes: litepanels.com... -
Page 10: Squares (Sharp Pulses)
Press to activate the Select LOOP MODE pulses manually at any or MANUAL MODE time PRESS Change Row MANUAL MODE = Activate the pulses with BUMP Only LOOP MODE = Pulses repeat as determined by OFF TIME setting Notes: litepanels.com... -
Page 11: Strobe
The DUTY setting can be used to create non-symmetrical flashing patterns where the light is, for example, ON for a very short portion of each time interval and OFF for a longer portion. This allows very precise control of the flash pattern. litepanels.com... -
Page 12: Tv/Monitor
Select the general CCT of the effect. WARM= Less than 3800K Change at any time (+- Green) due to Scene Changes or MOTION NEUT= 3800K < CCT < 4900K PRESS SML – Small COOL= > 4900K MED – Medium LRG – Large Notes: litepanels.com...