Download Print this page
Hide thumbs Also See for Sabre S4:

Advertisement

Quick Links

INTRODUCTION
BEFORE YOU START
The Sabre S4 is a professional 1/10 scale touring car and should be built
only by persons aged 16 years or older with previous experience building
and operating R/C model cars. This is not a toy and is not intended for
use by beginners or by children without direct supervision of a responsible,
knowledgeable adult.
Read the instruction manual carefully before
building.
T.O.P. Racing shall not be liable for any loss, injury or damages, whether
direct, indirect, special, incidental, or consequential, arising from the use,
misuse, or abuse of this product and/or any product or accessory required
to operate this product.
GENERAL PRECAUTIONS
This product is not suitable for children under 16 years of age without
the direct supervision of a knowledgeable adult.
Assemble this kit only in places away from the reach of small children.
First-time builders and users should seek advice from people who have
building experience in order to assemble the model correctly and to
allow the model to reach its performance potential.
Exercise care when using tools and sharp instruments.
Take care when building, as some parts may have sharp edges.
Keep small parts out of reach of small children. Children must not
be allowed to put any parts in their mouth, or pull vinyl bag over their
head.
Immediately after using your model, do not touch equipment on the
model such as the motor and speed controller, because they generate
high temperatures. You may seriously burn yourself by touching them.
Follow the operating instructions for the radio equipment at all times.
Do not put fingers or any objects inside rotating and moving parts, as
this may cause damage or serious injury as your finger, hair, clothes,
etc. may get caught.
Be sure that your operating frequency is clear before turning on or running
your model, and never share the same frequency with somebody else at
the same time. Ensure that others are aware of the operating frequency
you are using and when you are using it.
Always turn on your transmitter before turning on the receiver in the car.
Always turn off the receiver before turning off your transmitter.
Keep the wheels of the model off the ground when checking the
operation of the radio equipment.
Disconnect the battery pack before storing your model.
To prevent any serious personal injury and/or damage to property, be
responsible when operating all remote controlled models.
The model car is not intended for use on public places and roads or
areas where its operation can conflict with or disrupt pedestrian or
vehicular traffic.
Do not use your model:
1.
Near real cars, animals, or people that are unaware that an RC car
is being driven.
2.
In places where children and people gather
3.
In limited indoor spaces
4.
In wet conditions
5.
In the street
6.
In areas where loud noises can disturb others such as hospitals and
residential areas
7.
At night or anytime your line of sight to the model may be obstructed
or impaired in any way.
To prevent any serious personal injury and/or damage to property, please
be responsible when operating all remote controlled models.
ELECTRICAL PRECAUTIONS
Insulate any exposed electrical wiring (using heat shrink tubing or
electrical tape) to prevent dangerous short circuits. Take maximum
care in wiring, connecting and insulating cables. Make sure cables
are always connected securely. Check connectors for if they become
loose. And if so, reconnect them securely. Never use R/C models with
damaged wires. A damaged wire is extremely dangerous, and can
cause short-circuits resulting in fire.
Low battery power will result in loss of control. Loss of control can
occur due to a weak battery in either the transmitter or the receiver
Weak running battery may also result in an out of control car if your
car's receiver power is supplied by the running battery. Stop operation
immediately if the car starts to slow down.
When not using RC model, always disconnect and remove battery.
Do not disassemble battery or cut battery cables.
battery short-circuits, approximately 300W of electrical power can be
discharged, leading to fire or burns. Never disassemble battery or cut
battery cables.
Use a recommended charger for the receiver and transmitter batteries
and follow the instructions correctly. Over-charging, incorrect charging,
or using inferior chargers can cause the batteries to become dangerously
hot.
Recharge battery when necessary. Continual recharging may
damage battery and, in the worst case, could build up heat leading to
fire. If battery becomes extremely hot during recharging, please ask
your local hobby shop for check and/or repair and/or replacement.
Regularly check the charger for potential hazards such as damage to the
cable, plug, casing or other defects. Ensure that any damage is rectified
before using the charger again. Modifying the charger may cause short-
circuit or overcharging leading to a serious accident. Therefore do not
modify the charger.
Always unplug charger when recharging is finished.
Do not recharge battery while battery is still warm. After use, battery
retains heat. Wait until it cools down before charging.
Do not allow any metal part to short circuit the receiver batteries or other
electrical/electronic device on the model.
Immediately stop running if your RC model gets wet as may cause short
circuit.
Please dispose of batteries responsibly. Never put batteries into fire.
EQUIPMENT RECOMMENDED (NOT INCLUDED)
Radio Transmitter
Radio receiver
Batteries for Transmitter
Electronic Speed Control
Steering Servo
Brushless Motor System
Pinion Gear (48 Pitch)
7.4V Li-Po Pack
190mm Body Shell
Touring Car Wheels, Tires and Inserts
TOOLS RECOMMENDED (NOT INCLUDED)
1.5mm, 2.0mm, 3.0mm Allen Wrench
5.0mm, 5.5mm & 7.0mm Hex Socket Wrench
Modelers Craft Knife
Small Cross Head Screw Driver
Turnbuckle Wrench
Calipers/Ruler
Camber Gauge
Battery Strapping Tape
Instant Glue/Thread Lock
Shock Oil
Gear, Diff. Grease, Joint Grease, Gear Diff Oil
Paint (for Bodyshell)
If the running
NOTE:
The Sabre S4 chassis uses the best available components.
replacement parts can be purchased from your local hobby or model
shop.
There are 2 versions of the Sabre S4 - Standard Chassis and Stiff
Chassis. Ask you local hobby shops for confirming which kit you would
like to purchase.
This instruction manual contains a blank setup sheet for your own setup
record.
Enjoy building and driving your Sabre S4!!
All
Page 1

Advertisement

loading

Summary of Contents for T.O.P. Racing Sabre S4

  • Page 1 Near real cars, animals, or people that are unaware that an RC car EQUIPMENT RECOMMENDED (NOT INCLUDED) The Sabre S4 is a professional 1/10 scale touring car and should be built is being driven. only by persons aged 16 years or older with previous experience building In places where children and people gather •...
  • Page 2 * 組立ての際、 部品によっては端が鋭くなってますので、 注意して下さい。 塗料 (ボディー用) * バッテリーを分解したり、 バッテリーケーブルを切断したりしないで下さ * 小さな部品は、 小さなお子様の手の届かない場所に保管して下さい。 小さ   い。 もし駆動中のバッテリーがショートするとおよそ300Wの電力が放電 注意 :   なお子様が部品を飲み込んだり、 ビニール袋を頭から冠ったりしないよう   され火災や、 爆発を誘発します。 * Sabre S4 シャーシはベストな部品を使用します。 交換部品はお近く の模   注意下さい。 * 受信機、 送信機用バッテリーの充電には、 推奨された充電器を使用下さ 型店等、 弊社製品取扱い店でお求め下さい。   い。 必 * サーベルS4には2種類のバージョンがあります。 スタンダードシャーシ、 と * 使用後直後は、 大変高温度になってますので、 モーター、 スピードコントロ   ず、 充電器の取説マニュアルに従って正しく使用下さい。...
  • Page 3 BAG A BAG B PO-MGAS02 PO-MGBS01 TC-PMJS02 Gear Diff Case Small Bevel Gear TC-PML104 40T Pulley - One-Way ギアデフケース スモール べベルギア Bearing Cam 40T プーリー ワンウェイ ベアリングカム PO-MGBS01 Large Bevel Gear MP-TP-0004 ラージ べベルギア Spool Outdrive - Steel スプールアウトドライブ - スチール PO-MGAS02 PA-SP0208 40T Gear Diff Pulley TC-PML104 Steel Pin...
  • Page 4 BAG E x 1 TC-PDT007B Front Belt フロントベルト x 1 TC-SDT026BK Rear Belt リアベルト PA-SC0330 PA-LN00M3 Countersunk Stainless Steel Hex Screw M3 x 30 mm M3 Steel Nylon Lock Nut 皿ステンレス六角ビス M3 x 30 mm M3 スチールナイロンロックナット BAG G BAG F TC-SCHC038 Rear Shock Tower リアショックタワー...
  • Page 5 BAG K BAG I BAG J TC-PMMS02 Spring Adjust Nut Spacer x 6 TC-PSU005 スプリングアジャ ストナットスペーサ Tie Rod (Steel) M3 x 30mm TC-PSB012 14mm x 1 TC-SCH029RD タイロッド (スチール) M3 x 30mm Stabilizer Bar Bell Crank Bridge スタビライザーバー TC-PSH101RD ベルクランクブリッジ 1.2mm Shock Bottom Cap ショックボトムキャッ...
  • Page 6 BAG M PA-AP0001 PO-PXCH007RD Antenna Post TC-SCHC039 Alloy Servo Mount TC-PMPS01 TC-PMPS01 TC-PMPS01 アンテナポスト アロイ サーボマウント Battery Mount Plate Servo Arm Servo Arm Servo Arm バッテリーマウント プレート サーボアーム サーボアーム サーボアーム PA-SP0307 Futaba Hitec KO / Sanwa Bearing Flat Washer フラットワッシャー M3 x 7 x 0.5 x 10 PA-SB1005 PA-SB1510...
  • Page 7 SPOOL & GEAR DIFFERENTIAL \ スプール&ギアデフ BAG A Ball Bearing ベアリング PA-BM2504BK 10 x 15 x 4mm Button Head Screw SPOOL FINISHED ボタンヘッドネジ スプール完成 Button Head Screw M2.5 x 4mm ボタンヘッドネジ M2.5 x 4mm Ball Bearing ベアリング 10 x 15 x 4mm *NOTE: Add gear diff grease here (Not Included) *NOTE: Add gear diff grease here (Not Included) Large Bevel Gear...
  • Page 8 CENTER PULLEY ASSEMBLY \ センタープーリー 組立て PA-SCM205BK Chess Head Screw CENTER PULLEY ASSM. FINISHED Chess Head Screw チェスヘッドネジ チェスヘッ ドネジ センタープーリー組立て完成 Ball Bearing M2 x 5mm ベアリング 2 x 5mm 5 x 10 x 4mm PA-SB1005 Ball Bearing Chess Head Screw チェスヘッドネジ...
  • Page 9 NOTE : Default BEARING CAM marker position NOTE : Default BEARING CAM marker position 注意 : 初期設定 ベアリングカム マーカー位置 注意 : 初期設定 ベアリングカム マーカー位置 PA-SC0330 Countersunk Stainless Steel Hex Screw M3 x 30 mm 皿ステンレス六角ビス M3 x 30 mm PA-LN00M3 M3 Steel Nylon Lock Nut M3 スチールナイロンロックナット...
  • Page 10 SUSPENSION ARMS / サスペンションアーム PA-SS0308BK Set Screw イモネジ M3 x 8mm Front Arm 1.8mm フロントアーム NOTE : Assemble the left arms symmetrically to the right ones. 注意 : サスペンションアーム 左アームを右側に対して対称に組立 Rear Arm 1.8mm リアアーム SUSPENSION ASSEMBLY / サスペンション組立て Make 4 4個作成...
  • Page 11 FRONT SUSPENSION ASSEMBLY / フロントサスペンション組立て Make 2 Make 2 x 2 PO-SDT008 2個作成 2個作成 46mm Universal Bone *NOTE: Apply lubricant Set Screw 46mm ユニバーサルボーン “注意 : 潤滑剤塗布 イモネジ PO-DT0011 M3 x 3mm Steel Pin Universal Pin スチールピン ユニバーサル ピン 2 x 10mm 2 x 10mm Ball Bearing PA-SB1005...
  • Page 12 STERRING & LINKAGES / ステアリング/リンケージ PA-SS0306BK Set Screw イモネジ M3 x 6mm Set Screw Set Screw イモネジ イモネジ M3 x 6mm M3 x 6mm STERRING & LINKAGES / ステアリング/リンケージ Steering Link (make 2) Rear Camber Link (make 2) Front Camber Link (make 2) Servo Link ステアリングリンク...
  • Page 13 LINKAGES / リンケージ x 11 PA-BM0306BK Buttom Head Screw Front camber Link Buttom Head Screw ボタンヘッドネジ フロントキャンバーリンク ボタンヘッドネジ M3 x 6mm M3 x 6mm Steering Link ステアリングリンク Rear Camber Link リアキャンバーリンク Buttom Head Screw ボタンヘッドネジ M3 x 6mm Buttom Head Screw ボタンヘッ...
  • Page 14 STABILIZER BAR INSTALLATION/ スタビライザーバー取付け PA-HBS0508 Make 4 Ball Stud (Steel) Ball Cup FINISHED 4個作成 ボールカッ プ ボールスタッド (スチール) 完成 10.5mm 5.3 x 8mm PA-SS0303BK Collar カラー Ball Stud (Steel) ボールスタッド (スチール) 2.5mm M3 x 3mm 5.3 x 8mm TC-PMHS01 Ball Cup ボールカッ プ Ball Cup 14.5mm ボールカッ...
  • Page 15 SHOCK ASSEMBLY (MAKE 4) / ショック組立て (4個作成) 2mm E-Clip Shock Top Cap 2mm E- クリッ プ ショックトッ プキャッ プ Note: You could choose from a variety of shock piston to suit your needs. 注意 : さまざまなショックピストンから必要に応じて選ぶ Shock Bottom Cap ショックボトムキャッ プ Shock Piston 1.0mm hole 1.2mm hole...
  • Page 16 BUMPER & BODY POSTS / バンパー & ボディーポスト TC-PMQS01 Lower Bumper ローアーバンパー Bumper Assm. バンパー組立て M3 Nut M3 ナット PA-FN00M3 Lower Bumper M3 Nut ローアーバンパー M3 ナッ ト Button Head Screw ボタンヘッドネジ PA-BM0306BK Countersunk Screw M3 x 10mm Button Head Screw 皿ビス ボタンヘッ...
  • Page 17 SERVO INSTALLATION / サーボ取付け AW-M300RD Ultra Wide Collar ウルトラワイドカラー 3 x 7 x 3.0mm PA-SS0310BK Set Screw Set Screw イモネジ イモネジ Flat Washer M3 x 10mm フラットワッシャー M3 x 10mm M3 x 7 x 0.5 PA-SP0307 Flat Washer フラットワッシャー M3 x 7 x 0.5 Collar カラー...
  • Page 18 MOTOR & BATTERY GUIDE INSTALLATION / モーター & バッテリーガイド取付け PA-CM0310BK Countersunk Screw 皿ビス M3 x 10mm AW-BW31RD Small Bevel Washer スモール べベルワッシャー PA-SP0307 Flat Washer フラットワッシャー M3 x 7 x 0.5 PA-LN00M3 M3 Steel Nylon Lock Nut M3 スチールナイロンロックナット M3 Lock Nut M3 ロックナット Flat Washer フラットワッシャー...
  • Page 19 Your Sabre S4 is now ready to RUN!!! Sabre S4 走行用意!!! Page 19...
  • Page 22: Optional Parts List

    OPTIONAL PARTS LIST / オプションパーツリスト Chassis / シャーシ Shock Spring / ショックスプリング シリーズ フォームバンパー  (軽量) Gamma Shock Spring (14 x 1.5 x 5.50) 393gf/mm , 22.0lb/in Foam Bumper - Light Weight TC-PCH20L Gamma Shock Spring (14 x 1.5 x 5.50) 393gf/mm , 22.0lb/in PS-TR15550 オプション ステアリングポスト...