Download Print this page

Advertisement

Available languages

Available languages

Quick Links

INTRODUCTION
BEFORE YOU START
The Rebel R-F01 is a professional 1/10 scale rear-wheel drive
competition car and should be built only by persons aged 16 years or
older with previous experience building and operating R/C model cars.
This is not a toy and is not intended for use by beginners or by children
without direct supervision of a responsible, knowledgeable adult. Read
the instruction manual carefully before building.
T.O.P. Racing shall not be liable for any loss, injury or damages, whether
direct, indirect, special, incidental, or consequential, arising from the
use, misuse, or abuse of this product and/or any product or accessory
required to operate this product.
GENERAL PRECAUTIONS
This product is not suitable for children under 16 years of age without
the direct supervision of a knowledgeable adult.
Assemble this kit only in places away from the reach of small children.
First-time builders and users should seek advice from people who
have building experience in order to assemble the model correctly and
to allow the model to reach its performance potential.
Exercise care when using tools and sharp instruments.
Take care when building, as some parts may have sharp edges.
Keep small parts out of reach of small children. Children must not
be allowed to put any parts in their mouth, or pull vinyl bag over their
head.
Immediately after using your model, do not touch equipment on the
model such as the motor and speed controller, because they generate
high temperatures. You may seriously burn yourself by touching them.
Follow the operating instructions for the radio equipment at all times.
Do not put fingers or any objects inside rotating and moving parts, as
this may cause damage or serious injury as your finger, hair, clothes,
etc. may get caught.
Be sure that your operating frequency is clear before turning on
or running your model, and never share the same frequency with
somebody else at the same time. Ensure that others are aware of the
operating frequency you are using and when you are using it.
Always turn on your transmitter before turning on the receiver in the
car. Always turn off the receiver before turning off your transmitter.
Keep the wheels of the model off the ground when checking the
operation of the radio equipment.
Disconnect the battery pack before storing your model.
To prevent any serious personal injury and/or damage to property, be
responsible when operating all remote controlled models.
The model car is not intended for use on public places and roads or
areas where its operation can conflict with or disrupt pedestrian or
vehicular traffic.
Do not use your model:
1.
Near real cars, animals, or people that are unaware that an RC car
is being driven.
2.
In places where children and people gather
3.
In limited indoor spaces
4.
In wet conditions
5.
In the street
6.
In areas where loud noises can disturb others such as hospitals
and residential areas
7.
At night or anytime your line of sight to the model may be
obstructed or impaired in any way.
To prevent any serious personal injury and/or damage to property, please
be responsible when operating all remote controlled models.
ELECTRICAL PRECAUTIONS
Insulate any exposed electrical wiring (using heat shrink tubing or
electrical tape) to prevent dangerous short circuits. Take maximum
care in wiring, connecting and insulating cables. Make sure cables
are always connected securely. Check connectors for if they become
loose. And if so, reconnect them securely. Never use R/C models with
damaged wires. A damaged wire is extremely dangerous, and can
cause short-circuits resulting in fire.
Low battery power will result in loss of control. Loss of control can
occur due to a weak battery in either the transmitter or the receiver
Weak running battery may also result in an out of control car if your
car's receiver power is supplied by the running battery. Stop operation
immediately if the car starts to slow down.
When not using RC model, always disconnect and remove battery.
Do not disassemble battery or cut battery cables. If the running
battery short-circuits, approximately 300W of electrical power can be
discharged, leading to fire or burns. Never disassemble battery or cut
battery cables.
Use a recommended charger for the receiver and transmitter batteries
and follow the instructions correctly. Over-charging, incorrect
charging, or using inferior chargers can cause the batteries to become
dangerously hot. Recharge battery when necessary. Continual
recharging may damage battery and, in the worst case, could build
up heat leading to fire. If battery becomes extremely hot during
recharging, please ask your local hobby shop for check and/or repair
and/or replacement.
Regularly check the charger for potential hazards such as damage to
the cable, plug, casing or other defects. Ensure that any damage is
rectified before using the charger again. Modifying the charger may
cause short-circuit or overcharging leading to a serious accident.
Therefore do not modify the charger.
Always unplug charger when recharging is finished.
Do not recharge battery while battery is still warm. After use, battery
retains heat. Wait until it cools down before charging.
Do not allow any metal part to short circuit the receiver batteries or
other electrical/electronic device on the model.
Immediately stop running if your RC model gets wet as may cause
short circuit.
Please dispose of batteries responsibly. Never put batteries into fire.
EQUIPMENT RECOMMENDED (NOT INCLUDED)
Radio Transmitter
Radio receiver
Batteries for Transmitter
Electronic Speed Control
Steering Servo for 1/10 scale, Low profie
540 Type Motor or Brushless Motor System
Pinion Gear (64P)
3.7V 1S / 7.4V 2S / 7.4V 2S shorty pack
1/10 Scale Body Shell
Front and Rear Tire Set
Front spoiler and rear wing (Tamiya F1 compatible)
TOOLS RECOMMENDED (NOT INCLUDED)
1.5mm, 2.0mm, 3.0mm Allen Wrench
5.5mm & 7.0mm Hex Socket Wrench
Modelers Craft Knife
Turnbuckle Wrench
Calipers/Ruler
Camber Gauge
Battery Strapping Tape
Instant Glue/Thread Lock
Shock Oil
Thrust Grease, Diff. Grease, Joint Grease
Paint (for Bodyshell)
NOTE:
The Rebel F1 chassis uses the best available components. All
replacement parts can be purchased from your local hobby or model
shops who carry our products.
This instruction manual contains a blank setup sheet for your own
setup record.
Enjoy building and driving your Rebel R-F01!!
Page 1

Advertisement

loading

Summary of Contents for T.O.P. Racing Rebel R-F01

  • Page 1 • Pinion Gear (64P) T.O.P. Racing shall not be liable for any loss, injury or damages, whether At night or anytime your line of sight to the model may be • 3.7V 1S / 7.4V 2S / 7.4V 2S shorty pack direct, indirect, special, incidental, or consequential, arising from the obstructed or impaired in any way.
  • Page 2 組立て前には、 この取扱い説明書を読んで下さい に至るショートを起こす可性があります。 • ピニオンギア( 64ピッチ) • 低いバッテリーパワーはコントロールロスを招きます。 • 3.7V 1S/ 7.4V 2S/ 7.4V 2S ショートパック T.O.P. Racingでは、 直接、 間接、 特別、 偶発的、 結果的あらゆる使用上、 又は誤 • 送信機や、 受信機のパワーが落ちると制御が効かなくなります。 車が減 スケール用 ボディー • 1/10 使用、 不正使用により発生する損害、 怪我、 ダ 速し始めましたら、 すぐに操作中止下さい。 • フロント、 リア用 タイヤセット...
  • Page 3 BAG 1 BAG 2 x 2 PA-BM2506BK x 2 PC-RFCH010RD x 2 PC-RMCS05 x 2 PC-RMAS02 PC-RMAS01 Button Head Screw Front Cross Brace Tube Upper Hinge Pin Clip - 0.5mm Upper Eyelet Front Suspension Arm ボタンヘッ ドネジ フロントクロスブレスチュー フ x 2 PA-SS1818BK アッパーヒンジピンクリッ...
  • Page 4 BAG 6 BAG 8 BAG 11 x 4 AW-S100RD PC-RMBS01 x 2 PA-SS0308BK PC-RMAS07 Collar 3 x 5.5 x 1t Ball Cup 8.75mm Set Screw M3 x 8mm カラー 3 x 5.5 x 1t x 2 PC-RMDS04 ボールカッ プ 8.75mm イモネジ...
  • Page 5 BAG 13 BAG 14 x 4 AW-HBS004H x 1 PA-BM0306BK Ball Stud SS-KM01BK x 2 PA-CM0306BK x 4 PC-RCH019 ボールスタッ ト Button Head Screw x 2 PC-RFCHC008 Countersunk Screw M3 x 6mm Servo Saver - Mid Size ボタンヘッドネジ Body Post Roll Pin サーボセーバー...
  • Page 6 ロアーフロントサスペンション / LOWER FRONT SUSPENSION BAG 1 Button Head Screw ボタンヘッドネジ PA-BM2506BK M2.5 x 6mm Button Head Screw M2.5 x 6mm make 2 左 右 ボタンヘッ ドネジ M2.5 x 6mm 2個作成 LEFT RIGHT PA-BM2508BK Button Head Screw ボタンヘッドネジ Button Head Screw M2.5 x 8mm M2.5 x 8mm ボタンヘッ...
  • Page 7 サスペンション (続き) / SUSPENSION (cont’d) Front Cross Brace Insert フロントクロスブレースインサート Damper O-Ring 30-deg ダンパーOリング 30度 M3 Nut M3 ナット BAG 4 PA-CM0308BK Countersunk Screw 皿ビス Countersunk Screw M3 x 8mm M3 x 8mm 皿ビス M3 x 8mm Ultra Wide Collar 皿ビス...
  • Page 8 リア シャーシ / REAR CHASSIS Button Head Screw ボタンヘッドネジ Pivot Ball M3 x 6mm 注意 : ピボッ トボールの動きがしぶくならない程度 ピボットボール にピボッ トスクリューネジを締めます。 Note: Tighten the Pivot Socket Screw as far as it does not bind the free movement of the Pivot Ball. Countersunk Screw 皿ビス...
  • Page 9 リアサスペンションマウント / REAR SUSPENSION MOUNT クロスブレース / CROSS BRACE BAG 7 注意 : カーボン材の破損を防ぐために、 2箇所の穴を M3ねじ切り Ball Stud で事前処理します。 その際穴の半分の深さだけ にして下さい。 そう ボールスタット AW-HBS004H make 2 でないと、 穴が緩くなり過ぎます。 2個作成 Ball Stud Ball Stud Spacer Note: To avoid breakage of the carbon material, pre-tapp the ボールスタットスペーサー...
  • Page 10 リア サスペンション組立て / REAR SUSPENSION ASSEMBLY BAG 7 PA-CM2506BK Countersunk Screw Countersunk Screw M2.5 x 6mm 皿ビス 皿ビス M2.5 x 6mm M2.5 x 6mm PA-CM0306BK Countersunk Screw M3 x 6mm 皿ビス M3 x 6mm Countersunk Screw 皿ビス M3 x 6mm Ball Stud ボールスタット...
  • Page 11 リアアクスル 組立て / REAR AXLE ASSEMBLY BAG 11 PA-BM2508BK Button Head Screw M2.5 x 8mm Button Head Screw ボタンヘッ ドネジ M2.5 x 8mm ボタンヘッドネジ M2.5 x 8mm AW-S100RD Collar 3 x 5.5 x 1.0t Flanged Ball Bearing カラー 3 x 5.5 x 1.0t フランジボールベアリンク...
  • Page 12 リア デフ / REAR DIFFERENTIAL BAG 12 x 12 PO-CDB112BK Ball Bearing 1/4 x 3/8 ボールベアリンク 1/4 x 3/8 Ceramic Diff. Ball 1/8” セラミックデフボール 1/8” Ceramic Diff. Ball 1/8” セラミックデフボール 1/8” PA-SB0168 Ball Bearing 1/4 x 3/8 ボールベアリンク 1/4 x 3/8 Ball Bearing 1/4 x 3/8 ボールベアリンク...
  • Page 13: Steering Assembly

    ステアリング組立て / STEERING ASSEMBLY BAG 13 make 2 AW-S2650RD 2個作成 Ball Stud Spacer Button Head Screw ボタンヘッドネジ ボールスタッ トスペーサー M2.5 x 10mm Ball Cup - 16mm Tie Rod - 45mm Ball Cup - 16mm AW-HBS004H ボールカッ プ - 16mm タイロッ ド - 45mm ボールカッ...
  • Page 14 BAG 14 PA-FN00M3 M3 Nut M3 ナット PA-LN00M4 *NOTE: Sold Separately *注意 : 別売 M4 Steel Lock Nuts M4 スチールロックナット PA-CM0306BK Button Head Screw ボタンヘッドネジ Countersunk Screw M3 x 6mm M3 x 10mm 皿ビス M3 x 6mm PA-CM0308BK M4 Steel Lock Nuts M4 スチールロックナット...
  • Page 15 BAG 15 AW-M5100RD Collar 5 x 7 x 1.0t カラー 5 x 7 x 1.0t AW-M5050RD Collar 5 x 7 x 0.5t カラー 5 x 7 x 0.5t PA-SB0805 Ball Bearing 5 x 8 x 2.5mm ボールベアリンク 5 x 8 x 2.5mm Ball Bearing 5 x 8 x 2.5mm ボールベアリンク...
  • Page 18: Option Parts List

    Rebel F1 Standard Part List Option Parts List Suspension Linkage Drive Shaft PC-RFCH011 Inline Front Axle AW-HBS004H 4.3 Ball Stud PA-DR0003 Lightweight Diff. Ring (2pcs) PC-RCH011RD Dampner Tube PC-RLK002 Tie-Rod 40mm (2pcs) Chassis Ball Bearing PC-RCH012 Dampner Rod PC-RMBS02 Ball Cup - 16mm (5pcs) PC-PMQS04 Body Post Set PO-CBST08...
  • Page 19 オプションパーツリスト 標準パーツリスト Rebel F1 サスペンション リンケージ ドライブシャフト インライン フロントアクスル PC-RFCH011 4.3 ボールスタット AW-HBS004H 軽量デフリング (2 個) PA-DR0003 ダンパーチュー フ タイロッド 40mm (2 個) PC-RCH011RD PC-RLK002 シャーシ ダンパーロット PC-RCH012 ボールカッ プ - 16mm (5 個) PC-RMBS02 ボールベアリング ボディポスト フロントクロスブレスチュー フ サーボセーバーミドルサイズ ホール付き PC-PMQS04 PC-RFCH010RD SS-KM01BK セラミックボールベアリングセット...